Agilent Technologies U5303A User guide

Agilent Technologies
PCIe High-Speed Digitizer
2 Channels, 12-bit, up to 3.2 GS/s, DC up to 2 GHz
bandwidth, with on-board signal processing
U5303A
Startup Guide

Notices
© Agilent Technologies, Inc.
No part of this manual may be reproduced in
any form or by any means (including
electronic storage and retrieval or
translation into a foreign language) without
prior agreement and written consent from
Agilent Technologies, Inc. as governed by
United States and international copyright
laws.
Manual Part Number
U5303-90001
Edition
Wednesday, June 11, 2014
Sales and Technical Support
To contact Agilent for sales and technical
support, refer to the “support” links on the
following Agilent web resources:
nhttp://www.agilent.com/find/embed
ded
nwww.agilent.com/find/assist
(worldwide contact information for
repair and service)
Information on preventing damage to your
Agilent equipment can be found at
www.agilent.com/find/tips.
Regulatory Compliance
This product has been designed and tested
in accordance with accepted industry
standards, and has been supplied in a safe
condition. To review the Declaration of
Conformity, go to
http://regulations.corporate.agilent.com
/DoC/search.htm.
Warranty
The material contained in this document is
provided “as is,” and is subject to being
changed, without notice, in future editions.
Further, to the maximum extent permitted by
applicable law, Agilent disclaims all
warranties, either express or implied, with
regard to this manual and any information
contained herein, including but not limited to
the implied warranties of merchantability
and fitness for a particular purpose. Agilent
shall not be liable for errors or for incidental
or consequential damages in connection with
the furnishing, use, or performance of this
document or of any information
contained herein. Should Agilent and the
user have a separate written agreement with
warranty terms covering the material in this
document that conflict with these terms, the
warranty terms in the separate agreement
shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in
accordance with the terms of such license.
Restricted Rights Legend
If software is for use in the performance of a
U.S. Government prime contract or
subcontract, Software is delivered and
licensed as “Commercial computer software”
as defined in DFAR 252.227-7014 (June
1995), or as a “commercial item” as defined
in FAR 2.101(a) or as “Restricted computer
software” as defined in FAR 52.227-19 (June
1987) or any equivalent agency regulation or
contract clause. Use, duplication or
disclosure of Software is subject to Agilent
Technologies’ standard commercial license
terms, and non-DOD Departments and
Agencies of the U.S. Government will receive
no greater than Restricted Rights as defined
in FAR 52.227-19(c)(1-2) (June 1987). U.S.
Government users will receive no greater
than Limited Rights as defined in FAR
52.227-14 (June 1987) or DFAR 252.227-
7015 (b)(2) (November 1995), as applicable
in any technical data.
Safety Notices
The following safety precautions should be
observed before using this product and any
associated instrumentation.
This product is intended for use by qualified
personnel who recognize shock hazards and
are familiar with the safety precautions
required to avoid possible injury. Read and
follow all installation, operation, and
maintenance information carefully before
using the product.
If this product is not used as specified, the
protection provided by the equipment could
be impaired. This product must be used in a
normal condition (in which all means for
protection are intact) only.
The types of product users are:
nResponsible body is the individual or
group responsible for the use and
maintenance of equipment, for ensur-
ing that the equipment is operated
within its specifications and oper-
ating limits, and for ensuring oper-
ators are adequately trained.
nOperators use the product for its
intended function. They must be
trained in electrical safety pro-
cedures and proper use of the instru-
ment. They must be protected from
electric shock and contact with haz-
ardous live circuits.
nMaintenance personnel perform
routine procedures on the product to
keep it operating properly (for
example, setting the line voltage or
replacing consumable materials).
Maintenance procedures are
described in the user documentation.
The procedures explicitly state if the
operator may perform them. Other-
wise, they should be performed only
by service personnel.
nService personnel are trained to
work on live circuits, perform safe
installations, and repair products.
Only properly trained service per-
sonnel may perform installation and
service procedures.
Agilent products are designed for use with
electrical signals that are rated
Measurement Category I and Measurement
Category II, as described in the International
Electrotechnical Commission (IEC) Standard
IEC 60664. Most measurement, control, and
data I/O signals are Measurement Category
I and must not be directly connected to
mains voltage or to voltage sources with
high transient over-voltages. Measurement
Category II connections require protection
for high transient over-voltages often

associated with local AC mains connections.
Assume all measurement, control, and data
I/O connections are for connection to
Category I sources unless otherwise marked
or described in the user documentation.
Exercise extreme caution when a shock
hazard is present. Lethal voltage may be
present on cable connector jacks or test
fixtures. The American National Standards
Institute (ANSI) states that a shock hazard
exists when voltage levels greater than 30V
RMS, 42.4V peak, or 60VDC are present. A
good safety practice is to expect that
hazardous voltage is present in any unknown
circuit before measuring.
Operators of this product must be protected
from electric shock at all times. The
responsible body must ensure that operators
are prevented access and/or insulated from
every connection point. In some cases,
connections must be exposed to potential
human contact. Product operators in these
circumstances must be trained to protect
themselves from the risk of electric shock. If
the circuit is capable of operating at or
above 1000V, no conductive part of the
circuit may be exposed.
Do not connect switching cards directly to
unlimited power circuits. They are intended
to be used with impedance-limited sources.
NEVER connect switching cards directly to
AC mains. When connecting sources to
switching cards, install protective devices to
limit fault current and voltage to the card.
Before operating an instrument, ensure that
the line cord is connected to a properly-
grounded power receptacle. Inspect the
connecting cables, test leads, and jumpers
for possible wear, cracks, or breaks before
each use.
When installing equipment where access to
the main power cord is restricted, such as
rack mounting, a separate main input power
disconnect device must be provided in close
proximity to the equipment and within easy
reach of the operator.
For maximum safety, do not touch the
product, test cables, or any other
instruments while power is applied to the
circuit under test. ALWAYS remove power
from the entire test system and discharge
any capacitors before: connecting or discon-
necting cables or jumpers, installing or
removing switching cards, or making internal
changes, such as installing or removing
jumpers.
Do not touch any object that could provide a
current path to the common side of the
circuit under test or power line (earth)
ground. Always make measurements with dry
hands while standing on a dry, insulated
surface capable of withstanding the voltage
being measured.
The instrument and accessories must be
used in accordance with its specifications
and operating instructions, or the safety of
the equipment may be impaired.
Do not exceed the maximum signal levels of
the instruments and accessories, as defined
in the specifications and operating
information, and as shown on the instrument
or test fixture panels, or switching card.
When fuses are used in a product, replace
with the same type and rating for continued
protection against fire hazard.
Chassis connections must only be used as
shield connections for measuring circuits,
NOT as safety earth ground connections.
If you are using a test fixture, keep the lid
closed while power is applied to the device
under test. Safe operation requires the use
of a lid interlock.
Caution and Warning Notices
A CAUTION notice denotes a hazard. It calls
attention to an operating procedure,
practice, or the like that, if not correctly
performed or adhered to, could result in
damage to the product or loss of important
data. Do not proceed beyond a CAUTION
notice until the indicated conditions are fully
understood and met.
A WARNING notice denotes a hazard. It
calls attention to an operating procedure,
practice, or the like that, if not correctly
performed or adhered to, could result in
personal injury or death. Do not proceed
beyond a WARNING notice until the
indicated conditions are fully understood
and met.
Instrumentation and accessories shall not be
connected to humans.
Before performing any maintenance,
disconnect the line cord and all test cables.
To maintain protection from electric shock
and fire, replacement components in mains
circuits – including the power transformer,
test leads, and input jacks – must be
purchased from Agilent. Standard fuses with
applicable national safety approvals may be
used if the rating and type are the same.
Other components that are not safety-
related may be purchased from other
suppliers as long as they are equivalent to
the original component (note that selected
parts should be purchased only through
Agilent to maintain accuracy and
functionality of the product). If you are
unsure about the applicability of a
replacement component, call an Agilent
office for information.
Cleaning Precautions:
To prevent electrical shock, disconnect the
Agilent Technologies instrument from mains
before cleaning. Use a dry cloth or one
slightly dampened with water to clean the
external case parts. Do not attempt to clean
internally. To clean the connectors, use
alcohol in a well-ventilated area. Allow all
residual alcohol moisture to evaporate, and
the fumes to dissipate prior to energizing the
instrument.

Front and Rear Panel Symbols:
The CE mark is a registered
trademark of the European
Community.
The C-Tick mark is a
registered trademark of the
Australian Spectrum Management Agency.
This symbol indicates
product compliance
with the Canadian Interference-Causing
Equipment Standard (ICES-001). It also
identifies the product is an Industrial
Scientific and Medical Group 1 Class A
product (CISPR 11, Clause 4).
South Korean Class A EMC
Declaration. this equipment is
Class A suitable for professional
use and is for use in electro-
magnetic environments outside of the home.
A급 기기 ( 업무용 방송통신기자재 )
이 기기는 업무용 (A 급)전자파적합기
기로서 판 매자 또는 사용자는 이 점을
주
의하시기 바라 며 ,가정외의 지역에서
사용하는 것을 목적으 로 합니다 .
This symbol indicates separate
collection for electrical and
electronic equipment, mandated
under EU law as of August 13,
2005. All electric and electronic equipment
are required to be separated from normal
waste for disposal (Reference WEEE
Directive, 2002/96/EC).
This symbol indicates the time
period during which no hazardous
or toxic substance elements are
expected to leak or deteriorate during
normal use. Forty years is the expected
useful life of the product.
This symbol indicates the
instrument is sensitive to electro-
static discharge (ESD). ESD can
damage the highly sensitive components in
your instrument. ESD damage is most likely
to occur as the module is being installed or
when cables are connected or disconnected.
Protect the circuits from ESD damage by
wearing a grounding strap that provides a
high resistance path to ground. Alternatively,
ground yourself to discharge any built-up
static charge by touching the outer shell of
any grounded instrument chassis before
touching the port connectors.
This symbol denotes a hot surface.
The side cover of the module will be
hot after use and should be allowed
to cool for several minutes.

Table of Contents
Documentation Map 6
Agilent U5303A PCIe High-Speed Digitizer Introduction 7
Step 1: Unpack and Inspect the Module 9
Electrostatic Discharge (ESD) Precautions 9
Inspect for Damage 9
Return a Module for Service 9
Step 2: Verify U5303A Shipment Contents 10
Step 3: Install the Software 11
System Requirements 11
Hardware Requirements 11
Step 4: Install the Module 12
U5303A Front Panel Features 15
Step 5: Verify Operation of the U5303A Module 17
Perform a Verification of the U5303A (optional) 18

Documentation Map
Documentation Map
6 U5303A Startup Guide

Agilent U5303A PCIe High-Speed Digitizer Introduction
Agilent U5303A PCIe High-Speed Digitizer Introduction
The scope of this Startup Guide is to detail the processes of receiving and installing the Agilent U5303A PCIe
High-Speed Digitizer, installing the required software, and verifying basic module operation. If you have any
questions after reviewing this information, please contact your local Agilent representative or contact us through
our website at www.agilent.com/find/contactus
Related Documentation
This Startup Guide and the documentation listed below are contained on the
CD supplied with your product and at www.agilent.com/find/U5303A.
Select Technical Support > Manuals.
lU5303A User Manual
lHelp systems for the Agilent device drivers (IVI-C and IVI-COM, and
LabVIEW G)
lProduct specifications (Data Sheet)
Follow the Startup Sequence
This Start-Up Guide is intended to lead the user through the four steps of product installation as summarized in the
diagram below. An optional fifth step shows how to perform an operational verification of the U5303A PCIe High-
Speed Digitizer.
Step 1: Unpack and Inspect
Step 2: Verify Shipment
Step 3: Install Drivers and Software
Step 4: Install Modules
Closely follow the startup process flow in this document. Deviating from the sequence can
cause unpredictable system behavior, damage your system, and may cause personal injury.
Agilent U5303A Startup Guide 7

8 U5303A Startup Guide

Step 1: Unpack and Inspect the Module
Step 1: Unpack and Inspect the Module
The module is shipped in materials which prevent damage from static. The module should only be
removed from the packaging in an anti-static area ensuring that correct anti-static precautions are taken. Store all
modules in anti-static envelopes when not in use.
Electrostatic Discharge (ESD) Precautions
Electrostatic discharge (ESD) can damage or destroy
electronic components. Use a static-safe work station to
perform all work on electronic assemblies. The figure (left)
shows a static-safe work station using two types of ESD
protection: conductive table-mat and wrist-strap
combination, and conductive floor-mat and heel-strap
combination. Both types, when used together, provide a
significant level of ESD protection. Of the two, only the
table-mat and wrist-strap combination provides adequate
ESD protection when used alone. To ensure user safety, the
static-safe accessories must provide at least 1MΩ of
isolation from ground.
DONOT use these techniques for a static-
safe work station when working on circuitry with a
voltage potential greater than 500 volts.
Inspect for Damage
After unpacking a module, inspect it for any shipping damage. Report any damage to the shipping agent
immediately, as such damage is not covered by the warranty (see warranty information at beginning of this
document).
To avoid damage when handling a module, do not touch any exposed components or connector pins.
See www.agilent.com/find/tips for information on preventing damage to your Agilent equipment.
Return a Module for Service
Should it become necessary to return a module for repair or service, follow the steps below:
1. Review the warranty information shipped with your product.
2. Contact Agilent to obtain a Return Material Authorization (RMA) and return address. For assistance finding
Agilent contact information, go to www.agilent.com/find/assist (worldwide contact information for repair and
service) or refer to the “Support” information on the product web page at www.agilent.com/find/U5303A
3. Write the following information on a tag and attach it to the malfunctioning equipment:
lName and address of owner. A P.O. box is not acceptable as a return address.
lProduct model number (for example, U5303A).
Agilent U5303A Startup Guide 9

Step 2: Verify U5303A Shipment Contents
lProduct serial number. The serial number label is located on the top cover of the module. The serial
number can also be read from the Soft Front Panel interface, but only after the hardware is installed.
lDescription of failure or service required.
4. Pack the module in its original ESD bag and packing carton. If the original carton is not available, use bubble
wrap or packing peanuts and place the instrument in a sealed container and mark the container “FRAGILE”.
5. On the shipping label, write ATTENTION REPAIR DEPARTMENT and the RMA number.
If any correspondence is required, refer to the product by serial number and model number.
Step 2: Verify U5303A Shipment Contents
The following items are also included with your U5303A PCIe High-Speed Digitizer order:
Part Number Quantity Description
U5303A 1 PCIe High-Speed Digitizer.
8121-2530 1 Coaxial cable, MMCX to SMA, 1 m.
8121-2531 1 Auxiliary power cable, 4-Pin Male to Female 4-Conductor Floppy.
8121-2533 1 Auxiliary power cable, 15-Pin SATA Power Male to Power 4-Pin Floppy.
M9700-10001 1 Agilent MD2 High-Speed Digitizer Software & Product Information CD
E2094-60003 1 Agilent IO Libraries Suite CD.
U5303-90001 1 U5303A Startup Guide in hard copy.
5962-0476 1 Certificate of Calibration.
5959-4660 1 Recommended Due Date for Adjustment/Calibration.
9320-6741 1 ROHS (China addendum).
All the files contained on the CDs are available for download at www.agilent.com/find/U5303A.
10 U5303A Startup Guide

Step 3: Install the Software
Step 3: Install the Software
System Requirements
Item
Operating system Windows 7®
(32 or 64-bit), All versions.
Linux
Kernel 2.6 or higher (32 or 64-bit), Debian
7.0, CentOS 6.
Processor speed 1 GHz 32-bit (x86), 1 GHz 64-bit (x64),
no support for Itanium64
As per the minimum requirements of the
chosen distribution
Available memory 1 GB minimum As per the minimum requirements of the
chosen distribution
Available disk space 1
1.5 GB available hard disk space, includes:
l1 GB available for Microsoft .NET
Framework 3.5 SP1 2
l100 MB for Agilent IO Libraries Suite
100 MB
Video
Support for DirectX 9 graphics with 128 MB
graphics memory recommended (Super VGA
graphics is supported)
No graphics required (for headless system), or
X Windows
Browser Microsoft Internet Explorer 7.0 or higher Distribution supplied browser
1Because of the installation procedure, less disk space may be required for operation than is required for installation. The amount of space listed above is required for
installation.
2.NET Framework Runtime Components are often installed by default with Windows 7 and later versions. Therefore, you may not need this amount of available disk
space.
Hardware Requirements
A PC running one of the above operating systems. Recommended models are: HP Z420 or Dell T3610.
Install the Software
Agilent IO Libraries Suite (IOLS)
Agilent IO Libraries Suite (IOLS), which includes the Agilent Connection Expert. This software is included with
your shipment (CD part number E2904-60003), and is also available at www.agilent.com/find/IOsuite. This
software must be installed first.
1. From the Agilent IOLS CD (E2904-60003) browser launch the installer.
2. Follow the installer prompts to install the IO libraries.
Version 16.3 update 2 (or higher) of the Agilent IO Libraries Suite is required.
Version 17.0 (or higher) of the Agilent IO Libraries Suite requires MD2 version 1.3 (or higher).
Instrument software
Instrument software, which includes device drivers (IVI-C, IVI-COM) and documentation for your module. This
software is included with your shipment (CD part number M9700-10001).
1. From the Agilent MD2 High-Speed Digitizer Software & Product Information CD launch the installer.
2. Follow the installer prompts. Choose a "Complete" installation to install all software and documentation, or
a "Custom" installation to select from a listing of components and other features.
3. After installation is complete, please shut-down the PC.
Agilent U5303A Startup Guide 11

Step 4: Install the Module
Step 4: Install the Module
1. Ensure that the PC is switched off, and disconnect the power cord. Open the PC case.
Follow ESD precautions when handling and installing the U5303A.
2. The U5303A features a x8 PCIe bus interface, and should be installed in either a x8 or x16 slot.
3. When installing the U5303A ensure that it has optimum cooling, do not install it in a position where the
integrated cooling fans may be obstructed.
4. The module requires an additional auxiliary power connection to the white connector at top edge of the
module. If your PC has a free 'floppy drive power' connector, simply attach this.
If your PC does not have a free connector of this type you may use one of the two supplied adapters.
lIf your PC has spare 4-pin Molex power connectors, use the supplied adapter 8121-2531.
lIf your PC only has the newer SATA power connectors, use the supplied adapter 8121-2533.
5. Replace any covers and switch-on the PC. Check the module front panel indicators - a few seconds after the
boot process, both the 'Status' and 'DPU' LEDs should be green.
When disconnecting the auxiliary power cable, it is important to push it away from the PCB side of
the U5303A in order to disengage the friction lock. Failure to do this could cause the module side of the
connector to be withdrawn at the same time thus damaging it.
12 U5303A Startup Guide

Step 4: Install the Module
Note that the U5303A is optionally supplied with a card retainer (included if ordered as U5300A-001, or available
separately by ordering U1092-CRM) which is able to pick up on slots at the end the full-length PCIe slot and
provide additional support for the module. Use of this card retainer is highly recommended, in particular when the
PC motherboard is oriented vertically. However if your PC hardware does not provide end slots, the card retainer
may be removed from the module.
It is also possible to reverse the orientation of the fan assembly in the case that two modules must be placed in
adjacent slots, or other PC hardware obstructs the fitting. These three procedures are detailed below.
Fitting the module with the optional card retainer into your PC
1. Loosen (but do not remove) the screw (A) holding the rear card retainer, and slide it towards the fans.
2. Insert the module into the PCIe slot of the PC, ensuring that it is fully seated into the PCIe bus connector.
3. Fix the module to the PC either by fitting a screw, or by using a method integral to your PC model.
4. Fully extend the card retainer and ensure that it is inside the PC chassis support slot.
5. Tighten the screw (A) (0.5 Nm torque).
Figure 1 - Diagram showing fan/support assembly fixings (U5303A shown as example)
Agilent U5303A Startup Guide 13

Step 4: Install the Module
Removing the card retainer
1. Remove the screw (A) in the figure.
2. Withdraw the card retainer.
Installing the card retainer (if not previously fitted)
1. Slide the card retainer onto the fan module and fit screw (A) to the top of the retainer.
Reversing the orientation of the fan assembly
1. Remove the 4 screws (B) nearest to the front of the fan unit.
2. Slide the fan unit approximately 15 mm to the rear until it clears the circuit board, disconnect the power
cables, and rotate the fan unit by 180°.
3. Reconnect the power cables.
4. Slide the fan unit back towards the module until it is fully seated into the locating slots.
5. Refit the 4 screws, push the fan unit upwards away from the circuit board and tighten the four screws (0.5
Nm torque).
14 U5303A Startup Guide

Step 4: Install the Module
U5303A Front Panel Features
Front Panel Connectors
Connector Type Description
TRG IN MMCX External trigger input, 50 Ω DC terminated, ±5 V range.
IN 1, 2
SMA
The analog signal inputs, which are DC-coupled and 50 Ω terminated. The
input full scale ranges are selectable:
Range Maximum Input
1 V 3 Vrms, ±3.6 Vpk
2 V 4.3 Vrms, ± 6.3 Vpk
JTAG Micro
USB
Provides connection to the DPU for use with the U5340A FPGA Development
Kit.
TRGOUT MMCX Trigger Out signal. User selectable from several functions.
I/O 1, 2, 3 MMCX User configurable Input / Output signal. 3.3 V CMOS and TTLcompatible.
CLK IN MMCX External clock input. AC coupled and 50 Ω terminated, signal level: +5 to +15
dBm. Please refer to datasheet for details.
REF IN MMCX External reference clock input, AC coupled and 50 Ω terminated. It can accept
a 100MHz signal from -3 to +3 dBm.
Front Panel LEDs
Indicator Purpose Color State Meaning
DPU DPU status
Off DPU is not configured
Green, blinking Module initialization in progress
Green Module OK (firmware not yet loaded)
White DPU firmware loaded (ready)
STATUS Module status
White, blinking Firmware initialization in progress
Green, blinking Module initialization in progress
Yellow, blinking Warning
Red, blinking Error
Green OK (ready)
If warning or error status is observed, please try the following steps:
lPower-cycle the chassis (If using a PCIe interface to external PC, observe the power sequence require-
ments)
lIf the error persists please contact Agilent technical support
Agilent U5303A Startup Guide 15

16 U5303A Startup Guide

Step 5: Verify Operation of the U5303A Module
Step 5: Verify Operation of the U5303A Module
The intention of this step is to verify correct operation of the newly installed module. Run Agilent Connection
Expert by right-clicking the task bar icon , and select Agilent Connection Expert.
It will display the modules that are installed. Review the configuration data and then launch the SFP. This will
provide control of the module for self test and other operational verification procedures.
Agilent U5303A Instrument Properties
The instrument properties may
be viewed by clicking on the
desired instrument and then on
the Instrument Properties tab
in the right pane.
If the module
does not appear in the Agilent
Connection Expert, first try the
'Refresh All' button. If that
does not work, restart your PC
or embedded controller and
start Agilent Connection Expert
again.
Agilent U5303A Installed Software
A verification utility may be
launched by selecting the
Installed Software tab, selecting
the 'SFP - Verify Operation' item
and then clicking on Start SFP.
Agilent U5303A Startup Guide 17

Step 5: Verify Operation of the U5303A Module
Perform a Verification of the U5303A (optional)
Requirements for Verification
The correct operation of the U5303A may be verified by the use of a simple application which carries out several
performance checks on a signal acquired from an external Function Generator.
Required Hardware
An external signal source is required. Almost any sine wave or function generator capable of generating a signal
with an amplitude of 300 mV rms into 50 Ω at a frequency of 1 MHz may be used.
Hardware Description
Analog Signal Generator e.g. Agilent N5181A, E4428C, ..
SMA cable 50 Ω Coaxial cable with SMA(m)
Operational Verification Procedure
Do not exceed the maximum voltage level at the INPUT connector.
1. Configure the RF Generator to produce a Sine signal with a Frequency of 1.0 MHz, an Amplitude of
300mV rms (+2.55 dBm).
2. Connect the Signal Generator output to the IN 1 connector, and turn on the output.
3. Launch the Verify utility from Agilent Connection Expert as explained in Step 5 of this Startup Guide. A
command shell window will open.
4. Press any key to start the test. The screen capture below shows the result of a successful verification:
If a Problem is Found
1. Verify that you have made all configuration settings as shown above.
2. Verify that the RF generator is ON and producing the desired signals at the end of the cable. This can be
done with an oscilloscope.
3. Verify that the problem is reproducible.
4. Contact Agilent technical support for assistance. Contact details may be found at:
www.agilent.com/find/contactus
18 U5303A Startup Guide

19 U5303A Startup Guide

The Modular Tangram
The four-sided geometric symbol that appears in Agilent modular
product literature is called a tangram. The goal of this seven-piece
puzzle is to create shapes—from simple to complex. As with a
tangram, the possibilities may seem infinite as you begin to create
a new test system. With a set of clearly defined elements—
hardware, software—Agilent can help you create the system you
need, from simple to complex.
Challenge the Boundaries of Test
Agilent Modular Products
myAgilent
www.agilent.com/find/myagilent
A personalized view into the information most
relevant to you.
www.axiestandard.org
AdvancedTCA® Extensions for Instrumentation and
Test (AXIe). Agilent is a founding member.
www.pxisa.org
PCI eXtensions for Instrumentation (PXI) modular
instrumentation.
www.pcisig.com
PCI Express, industry standard platform.
Three-Year Warranty
www.agilent.com/find/ThreeYearWarranty
Agilent’s combination of product reliability and
three-year warranty coverage is another way we
help you achieve your business goals: increased
confidence in uptime & reduced cost of ownership.
Agilent Advantage Services
www.agilent.com/find/AdvantageServices
PCI Accurate measurements throughout the life of
your instrument.
www.agilent.com/quality
www.agilent.com
www.agilent.com/find/modular
www.agilent.com/find/U5303A
For more information on Agilent Technologies' products,
applications or services, please contact your local Agilent office.
For complete listings: www.agilent.com/find/contactus.)
Americas
Canada [phone]
Brazil (11) 4197 3500
Mexico 01800 5064 800
United States [phone]
Asia Pacific
Australia 1 800 629 485
China 800 810 0189
Hong Kong 800 938 693
India 1 800 112 929
Japan 0120 (421) 345
Korea 080 769 0800
Malaysia 1 800 888 848
Singapore 1 800 375 8100
Taiwan 0800 047 866
Thailand 1 800 226 008
Europe & Middle East
Austria 43 (0) 1 360 277 1571
Belgium 32 (0) 2 404 93 40
Denmark 45 70 13 15 15
Finland 358 (0) 10 855 2100
France 0825 010 700 (0.125 €/minute)
Germany 49 (0) 7031 464 6333
Ireland 1890 924 204
Israel 972 3 9288 504 / 544
Italy 39 02 92 60 8484
Netherlands 31 (0) 20 547 2111
Spain 34 (91) 631 3300
Sweden 0200 88 22 55
Switzerland 0800 80 53 53
United Kingdom 44 (0) 118 9276201
© Agilent Technologies, Inc. 2014