Agilent Technologies 8960 Instruction Manual

s1
Agilent Technologies 8960 Series 10 E5515B,C,T Wireless Communications Test Set
Manual Operation: Getting Started Guide
AMPS/136 Mobile Test Application E1961A Revision: A.04
cdma2000/IS-2000 Mobile Test Application E1962A Revision A.01, E1962B Revision: B.01
GPRS Mobile Test Application E1964A Revision: A.01
GSM Mobile Test Application E1960A Revision: A.07
GSM_AMPS/136 Fast Switch Mobile Test Application E1985A Revision: A.01
Agilent Part No: 5967-5124
Print Date: March 2001
© Copyright Agilent Technologies 2001
All Rights Reserved
http://www.agilent.com/find/8960support
深圳德标仪器 135-1095-0799

2
Edition/Print Date
All Editions and Updates of this manual and their creation dates are listed below.
March 2001 - 5967-5124
Safety Summary
The following general safety precautions must be observed during all phases of operation of
this instrument. Failure to comply with these precautions or with specific warnings elsewhere
in this manual violates safety standards of design, manufacture, and intended use of the
instrument. Agilent Technologies Inc. assumes no liability for the customer’s failure to comply
with these requirements.
GENERAL
This product is a Safety Class 1 instrument (provided with a protective earth terminal). The
protective features of this product may be impaired if it is used in a manner not specified in
the operation instructions.
All Light Emitting Diodes (LEDs) used in this product are Class 1 LEDs as per IEC 60825-1.
This product has been designed and tested in accordance with IEC Publication 1010, "Safety
Requirements for Electronic Measuring Apparatus," and has been supplied in a safe
condition. This instruction documentation contains information and warnings which must be
followed by the user to ensure safe operation and to maintain the product in a safe condition.
深圳德标仪器 135-1095-0799

3
ENVIRONMENTAL CONDITIONS
This instrument is intended for indoor use in an installation category II, pollution degree 2
environment. It is designed to operate at a maximum relative humidity of 95% and at
altitudes of up to 2000 meters. Refer to the specifications tables for the ac mains voltage
requirements and ambient operating temperature range.
Ventilation Requirements: When installing the product in a cabinet, the convection into and
out of the product must not be restricted. The ambient temperature (outside the cabinet) must
be less than the maximum operating temperature of the product by 4°C for every 100 watts
dissipated in the cabinet. If the total power dissipated in the cabinet is greater than 800
watts, then forced convection must be used.
BEFORE APPLYING POWER
Verify that the product is set to match the available line voltage, the correct fuse is installed,
and all safety precautions are taken. Note the instrument's external markings described
under Safety Symbols.
GROUND THE INSTRUMENT
To minimize shock hazard, the instrument chassis and cover must be connected to an
electrical protective earth ground. The instrument must be connected to the ac power mains
through a grounded power cable, with the ground wire firmly connected to an electrical
ground (safety ground) at the power outlet. Any interruption of the protective (grounding)
conductor or disconnection of the protective earth terminal will cause a potential shock
hazard that could result in personal injury.
FUSES
Only fuses with the required rated current, voltage, and specified type (normal blow, time
delay, etc.) should be used. Do not use repaired fuses or short-circuited fuse holders. To do so
could cause a shock or fire hazard.
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of flammable gases or fumes.
DO NOT REMOVE THE INSTRUMENT COVER
Operating personnel must not remove instrument covers. Component replacement and
internal adjustments must be made only by qualified service personnel.
Instruments that appear damaged or defective should be made inoperative and secured
against unintended operation until they can be repaired by qualified service personnel.
深圳德标仪器 135-1095-0799

4
WARNING The WARNING sign denotes a hazard. It calls attention to a
procedure, practice, or the like, which, if not correctly
performed or adhered to, could result in personal injury. Do not
proceed beyond a WARNING sign until the indicated conditions
are fully understood and met.
CAUTION The CAUTION sign denotes a hazard. It calls attention to an operating
procedure, or the like, which, if not correctly performed or adhered to,
could result in damage to or destruction of part or all of the product. Do
not proceed beyond a CAUTION sign until the indicated conditions are
fully understood and met.
Safety Symbols
Caution, refer to accompanying documents
Warning, risk of electric shock
Earth (ground) terminal
Alternating current
Frame or chassis terminal
Standby (supply). Units with this symbol are not completely disconnected from ac
mains when this switch is off.
To completely disconnect the unit from ac mains, either disconnect the power cord, or have a
qualified electrician install an external switch.
深圳德标仪器 135-1095-0799

5
Product Markings
CE - the CE mark is a registered trademark of the European Community. A CE mark
accompanied by a year indicated the year the design was proven.
CSA - the CSA mark is a registered trademark of the Canadian Standards Association.
CERTIFICATION
Agilent Technologies certifies that this product met its published specifications at the time of
shipment from the factory. Agilent Technologies further certifies that its calibration
measurements are traceable to the United States National Institute of Standards and
Technology, to the extent allowed by the Institute’s calibration facility, and to the calibration
facilities of other International Standards Organization members
深圳德标仪器 135-1095-0799

6
Agilent Technologies Warranty Statement for
Commercial Products
Agilent Technologies 8960 Series 10 E5515B,C,T Wireless Communications Test Set,
AMPS/136 Mobile Test Application E1961A
cdma2000 Mobile Test Application E1962B
GPRS Mobile Test Application E1964A
GSM Mobile Test Application E1960A
IS-2000 Mobile Test Application E1962A
Duration of Warranty: 1 year
1. Agilent Technologies warrants Agilent Technologies hardware, accessories and supplies
against defects in materials and workmanship for the period specified above. If Agilent
Technologies receives notice of such defects during the warranty period, Agilent
Technologies will, at its option, either repair or replace products which prove to be
defective. Replacement products may be either new or like-new.
2. Agilent Technologies warrants that Agilent Technologies software will not fail to execute
its programming instructions, for the period specified above, due to defects in material and
workmanship when properly installed and used. If Agilent Technologies receives notice of
such defects during the warranty period, Agilent Technologies will replace software media
which does not execute its programming instructions due to such defects.
3. Agilent Technologies does not warrant that the operation of Agilent Technologies products
will be uninterrupted or error free. If Agilent Technologies is unable, within a reasonable
time, to repair or replace any product to a condition as warranted, customer will be
entitled to a refund of the purchase price upon prompt return of the product.
4. Agilent Technologies products may contain remanufactured parts equivalent to new in
performance or may have been subject to incidental use.
5. The warranty period begins on the date of delivery or on the date of installation if installed
by Agilent Technologies. If customer schedules or delays Agilent Technologies installation
more than 30 days after delivery, warranty begins on the 31st day from delivery.
深圳德标仪器 135-1095-0799

7
6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance
or calibration, (b) software, interfacing, parts or supplies not supplied by Agilent
Technologies, (c) unauthorized modification or misuse, (d) operation outside of the
published environmental specifications for the product, or (e) improper site preparation or
maintenance.
7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE
EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN
OR ORAL IS EXPRESSED OR IMPLIED AND AGILENT TECHNOLOGIES
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OR
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A
PARTICULAR PURPOSE.
8. Agilent Technologies will be liable for damage to tangible property per incident up to the
greater of $300,000 or the actual amount paid for the product that is the subject of the
claim, and for damages for bodily injury or death, to the extent that all such damages are
determined by a court of competent jurisdiction to have been directly caused by a defective
Agilent Technologies product.
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY
STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS
INDICATED ABOVE, IN NO EVENT WILL AGILENT TECHNOLOGIES OR ITS
SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER
DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW ZEALAND: THE
WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT
LAWFULLY PERMITTED, DO NOT EXCLUDE RESTRICT OR MODIFY AND ARE IN
ADDITION TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE
OF THIS PRODUCT TO YOU.
ASSISTANCE
Product maintenance agreements and other customer assistance agreements are available for
Agilent Technologies products. For any assistance, contact your nearest Agilent Technologies
Sales and Service Office.
深圳德标仪器 135-1095-0799

8
Service and Support
Any adjustment, maintenance, or repair of this product must be performed by qualified
personnel. Contact your customer engineer through your local Agilent Technologies Service
Center. You can find a list of local service representatives on the Web at:
http://www.agilent-tech.com/services/English/index.html
If you do not have access to the Internet, one of these centers can direct you to your nearest
representative:
United States Test and Measurement Call Center
(Toll free in US)
[phone]
Europe
(31 20) 547 9900
Canada
[phone]
Japan Measurement Assistance Center
(81) 426 56 7832
(81) 426 56 7840 (FAX)
Latin America
[phone] (FAX)
Australia/New Zealand
1 800 629 485 (Australia)
0800 738 378 (New Zealand)
Asia-Pacific
(852) 2599 7777
(852) 2506 9285 (FAX)
深圳德标仪器 135-1095-0799

9
Regional Sales Offices
United States of America:
Agilent Technologies (tel) 1 800 452 4844
Test and Measurement Call Center
P.O. Box 4026
Englewood, CO 80155-4026
Canada:
Agilent Technologies Canada Inc. (tel) 1 877 894 4414
2660 Matheson Blvd. E
Mississauga, Ontario
L4W 5G1
Europe:
Agilent Technologies (tel) (3120) 547 9999
European Marketing Organization
P.O. Box 999
1180 AZ Amstelveen
The Netherlands
Japan:
Agilent Technologies Japan Ltd. (tel) (81) 456-56-7832
Measurement Assistance Center (fax) (81) 426-56-7840
9-1 Takakura-Cho, Hachioji-Shi,
Tokyo 192-8510, Japan
Latin America:
Agilent Technologies (tel) [phone]
Latin America Region Headquarters (fax) [phone]
5200 Blue Lagoon Drive,
Suite #950
Miami, Florida 33126
U.S. A.
深圳德标仪器 135-1095-0799

10
Australia/New Zealand:
Agilent Technologies Australia Pty Ltd. Australia New Zealand
347 Burwood Highway (tel) 1 800 629 485 (tel) 0 800 738 378
Forest Hill, Victoria 3131 (fax) (61 3) 9272 0749 (fax) (64 4) 802
6881
Asia Pacific:
Agilent Technologies (tel) (852) 3197 7777
24/F, Cityplaza One, (fax) (852) 2506 9233
111 Kings Road,
Taikoo Shing, Hong Kong
深圳德标仪器 135-1095-0799