Agilent Technologies U2701A User manual

Agilent Technologies
Agilent U2701A/U2702A
USB Modular
Oscilloscopes
User’s Guide
U2700A_Modular_Scope.book Page i Tuesday, May 6, 2008 9:32 AM

Notices
© Agilent Technologies, Inc. 2008
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
U2702-90013
Edition
First Edition, April 29, 2008
Printed in Malaysia
Agilent Technologies, Inc.
3501 Stevens Creek Blvd.
Santa Clara, CA 95052 USA
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
U.S. Government Restricted Rights. Soft-
ware and technical data rights granted to
the federal government include only those
rights customarily provided to end user cus-
tomers. Agilent provides this customary
commercial license in Software and techni-
cal data pursuant to FAR 12.211 (Technical
Data) and 12.212 (Computer Software) and,
for the Department of Defense, DFARS
252.227-7015 (Technical Data - Commercial
Items) and DFARS 227.7202-3 (Rights in
Commercial Computer Software or Com-
puter Software Documentation).
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.
ii U2701A/U2702A Modular Oscilloscopes User’s Guide
Trademark Acknowledgements
Pentium is a U.S. registered trademark of
Intel Corporation.
Microsoft, Visual Studio, Windows, and MS
Windows are trademarks of Microsoft Cor-
poration in the United States and/or other
countries.
U2700A_Modular_Scope.book Page ii Tuesday, May 6, 2008 9:32 AM

U2701A/U2702A USB Modular Oscilloscopes User’s Guide iii
Safety Symbols
The following symbols on the instrument and in the documentation
indicate precautions which must be taken to maintain safe operation of
the instrument.
Direct current (DC) Off (supply)
Alternating current (AC) On (supply)
Both direct and alternating
current
Caution, risk of electric shock.
Three-phase alternating current Caution, risk of danger (refer to
this manual for specific Warning
or Caution information).
Earth (ground) terminal Caution, hot surface.
Protective conductor terminal Out position of a bi-stable push
control.
Frame or chassis terminal In position of a bi-stable push
control.
Equipotentiality CAT I Category I Overvoltage
Protection
Equipment protected throughout
by double insulation or reinforced
insulation.
U2700A_Modular_Scope.book Page iii Tuesday, May 6, 2008 9:32 AM

iv U2701A/U2702A Modular Oscilloscopes User’s Guide
General Safety Information
The following general safety precautions must be observed
during all phases of operation, service and repair of this
instrument. Failure to comply with these precautions or with
specific warnings elsewhere in this manual violates safety
standards of design, manufacturer and intended use of the
instrument. Agilent Technologies assumes no liability for the
customer’s failure to comply with these requirements.
WARNING
• Observe all markings on the equipment before connecting any wiring
to the equipment.
• This equipment is under CAT1 measurement category, do not connect
the test probe to MAIN.
• Do not measure more than rated voltage (as marked on the
equipment).
• Inspect the test probe for damaged insulation or expose metal and
check for continuity. Do not use test probe if found damaged.
• Do not operate the equipment in an explosive atmosphere or in the
presence of flammable gases or fumes.
• Do not use the equipment if it does not operate properly. Have the
equipment inspected by qualified service personal. If necessary,
return the equipment to Agilent for service and repair to ensure that
safety features are maintained.
CAUTION
• Always disconnect the probes from the measuring circuit before
disconnecting the adapter.
• Use the device with the cables provided.
• Repair or service that is not covered in this manual should only be
performed by qualified personnels.
• Applying excessive voltage or overloading the device will cause
irreversible damage to the circuitry.
CAT1:
Maximum Working Voltage: 30 Vrms or 42 Vpeak or 60 Vdc
U2700A_Modular_Scope.book Page iv Tuesday, May 6, 2008 9:32 AM

U2701A/U2702A USB Modular Oscilloscopes User’s Guide v
Environment Conditions
This instrument is designed for indoor use only. Table 1 shows
general environmental requirements for this instrument.
Ta b l e 1 Environment Requirements
Environmental Conditions Requirements
Operating Temperature 0 °C to 50 °C
Storage Temperature –20 °C to 70 °C
Operating Humidity 20 to 85% RH (non-condensing)
Storage Humidity 5 to 90% RH (non-condensing)
CAUTION
The Agilent U2701A/U2702A are safety-certified in compliance with the
following safety and EMC requirements:
•IEC 61010-1: 2001/EN 61010-1: 2001 (2nd edition)
•CAN/CSA-C22.2 No. 61010-1-04
•IEC 61326-2002/EN 61326: 1997+A1: 1998+A2: 2001+A3: 2003
•ICES-001: 2004
•AS/NZS CISPR11: 2004
•USA: ANSI/UL 61010-1:2004
U2700A_Modular_Scope.book Page v Tuesday, May 6, 2008 9:32 AM

vi U2701A/U2702A Modular Oscilloscopes User’s Guide
Regulatory Markings
The CE mark is a registered trademark
of the European Community.This CE
mark shows that the product complies
with all the relevant European Legal
Directives.
The C-tick mark is a registered trademark
of the Spectrum Management Agency of
Australia. This signifies compliance with
the Australia EMC Framework
regulations under the terms of the Radio
Communication Act of 1992.
ICES/NMB-001 indicates that this ISM
device complies with Canadian
ICES-001.
Cet appareil ISM est confomre à la
norme NMB-001 du Canada.
This instrument complies with the WEEE
Directive (2002/96/EC) marking
requirement. This affixed product label
indicates that you must not discard this
electrical/electronic product in domestic
household waste.
The CSA mark is a registered trademark
of the Canadian Standards Association.
U2700A_Modular_Scope.book Page vi Tuesday, May 6, 2008 9:32 AM

U2701A/U2702A USB Modular Oscilloscopes User’s Guide vii
Waste Electrical and Electronic Equipment (WEEE) Directive
2002/96/EC
This instrument complies with the WEEE Directive (2002/96/EC) marking
requirement. This affixed product label indicates that you must not discard
this electrical/electronic product in domestic household waste.
Product Category:
With reference to the equipment types in the WEEE directive Annex 1, this
instrument is classified as a “Monitoring and Control Instrument” product.
The affixed product label is shown as below:
Do not dispose in domestic household waste
To return this unwanted instrument, contact your nearest Agilent office, or
visit:
www.agilent.com/environment/product
for more information.
U2700A_Modular_Scope.book Page vii Tuesday, May 6, 2008 9:32 AM

viii U2701A/U2702A Modular Oscilloscopes User’s Guide
DECLARATION OF CONFORMITY
According to EN ISO/IEC 17050-1:2004
Generic example
Manufacturer’s Name: Agilent Technologies Microwave Products (M) Sdn. Bhd
Manufacturer’s Address: Bayan Lepas Free Industrial Zone,
11900, Bayan Lepas, Penang, Malaysia
Declares under sole responsibility that the product as originally delivered
Product Name: Agilent USB Modular Oscilloscope
Models Number: U2701A, U2702A
Product Options: This declaration covers all options of the above product(s)
complies with the essential requirements of the following applicable European Directives, and
carries the CE marking accordingly:
Low Voltage Directive (2006/95/EC)
EMC Directive (2004/108/EC)
and conforms with the following product standards:
EMC Standard
StandardStandard
Standard
Limit LimitLimit
Limit
IEC 61326:2002 / EN 61326:1997+A1:1998+A2:2001+A3:2003
CISPR 11:1990 / EN55011:1990 Class A Group 1
IEC 61000-4-2:1995 / EN 61000-4-2:1995 4 kV CD, 8 kV AD
IEC 61000-4-3:1995 / EN 61000-4-3:1996 3 V/m, 80-1000 MHz
IEC 61000-4-4:1995 / EN 61000-4-4:1995 0.5 kV signal lines, 1 kV power lines
IEC 61000-4-5:1995 / EN 61000-4-5:1995 0.5 kV line-line, 1 kV line-ground
IEC 61000-4-6:1996 / EN 61000-4-6:1996 3 V, 0.15-80 MHz
IEC 61000-4-11:1994 / EN 61000-4-11:1994 1 cycle / 100%
Canada: ICES-001:2004
Australia/New Zealand: AS/NZS CISPR11:2004
The product was tested in a typical configuration with Agilent Technologies test systems.
Safety
IEC 61010-1:2001 / EN 61010-1:2001
Canada: CAN/CSA-C22.2 No. 61010-1-04
USA: ANSI/UL 61010-1:2004
206349
This DoC applies to above-listed products placed on the EU market after:
14-March-2008
Date
Tay Eng Su
Quality Manager
For further information, please contact your local Agilent Technologies sales office, agent or distributor,
or Agilent Technologies Deutschland GmbH, Herrenberger Straße 130, 71034 Böblingen, Germany.
Template: A5971-5302-2, Rev. E U2701A DoC Revision 1.0
U2700A_Modular_Scope.book Page viii Tuesday, May 6, 2008 9:32 AM

U2701A/U2702A USB Modular Oscilloscopes User’s Guide ix
Product Regulations
Performance Criteria
IEC 61326-1:2002 / EN 61326-1:1997+A1:1998+A2:2001+A3:2003
CISPR 11:1990 / EN 55011:1990
– Group 1 Class A
IEC 61000-4-2:1995 / EN 61000-4-2:1995 (ESD 4kV CD, 8kV AD) A
IEC 61000-4-3:1995 / EN 61000-4-3:1996 (3V/m, 80% AM) A
IEC 61000-4-4:1995 / EN 61000-4-4:1995 (EFT 0.5kV line-line, 1kV line-earth) A
IEC 61000-4-5:1995 / EN 61000-4-5:1995 (Surge 0.5kV line-line, 1kV line-earth) A
IEC 61000-4-6:1996 / EN 61000-4-6:1996 (3V, 0.15~80 MHz, 80% AM, power line) A
IEC 61000-4-11:1994 / EN 61000-4-11:1994 (Dips 1 cycle, 100%) A
Canada: ICES-001:2004
Australia/New Zealand: AS/NZS CISPR11:2004
EMC
IEC 61010-1:2001 / EN 61010-1:2001
Canada: CAN/CSA-C22.2 No. 61010-1-04
USA: ANSI/UL 61010-1:2004
Safety
Additional Information:
The product herewith complies with the essential requirements of the Low Voltage Directive 2006/95/EC and the
EMC Directive 2004/108/EC and carries the CE Marking accordingly (European Union).
1
Performance Criteria:
A Pass - Normal operation, no effect.
B Pass - Temporary degradation, self recoverable.
C Pass - Temporary degradation, operator intervention required.
D Fail - Not recoverable, component damage.
N/A – Not applicable
Notes:
Regulatory Information for Canada
ICES/NMB-001:2004
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est confomre à la norme NMB-001 du Canada.
Regulatory Information for Australia/New Zealand
This ISM device complies with Australian/New Zealand AS/NZS CISPR11:2004
U2700A_Modular_Scope.book Page ix Tuesday, May 6, 2008 9:32 AM

x U2701A/U2702A Modular Oscilloscopes User’s Guide
In This Guide…
1 Getting Started provides an overview of the U2701A/U2702A
USB modular oscilloscopes, the product outlook, and product
dimensions. This chapter also includes information on
checklist, system requirements, and installation of hardware.
2 Scope Features and Functions define the U2701A/U2702A USB
modular oscilloscopes various operations.
3 Characteristics and Specifications specifies the characteristics
and specifications of the U2701A/U2702A USB modular
oscilloscope.
U2700A_Modular_Scope.book Page x Tuesday, May 6, 2008 9:32 AM