Agria 5500 CT User manual

TT
TT
Tool Carool Car
ool Carool Car
ool Carrierrier
rierrier
rier
5500 CT5500 CT
5500 CT5500 CT
5500 CT
Quick start guideQuick start guide
Quick start guideQuick start guide
Quick start guide
agria-Werke GmbH • D-74219 Möckmühl • Tel. [phone] • Fax [phone]
998 592a_GB 08.10

5500 CT
Quick start guide
5500 644 Page 2 of 7 998 592a_GB 08.10
Before commissioning the machine please read operating instructions
Check all fluids, settings, warnings and safety instructions!
Check the machine
Prior to operating the machine and after 10 hours
Check oil level
Fill if level is below min Clean cooling system from dust and dirt If air filter indicator changes to red change filter element
Operating instruction
in black box on board Service manual and documents
with the machine
Tools
in black toolbox
max
min
Height adjustment
loosen bot
h lock nuts (A)
and hex head bolts (B)
bring the handlebar to desired
height
fasten bolts and nuts
Lateral adjustment
Pull ball handle (B/1) upwards
turn handlebar into desired
position / release ballhandle
Vital information on the cleaning
of the cooling system on top of
the fuel tank
Important Information Handlebar adjustment

5500 CT
Quick start guide
5500 644 Page 3 of 7 998 592a_GB 08.10
Start engine (step by step)
Switch off engine
Let engine run at increased idling speed for a minute to cool down
and to avoid carbon to deposit on the injection valve before machine is turned off !
(1) Push safety circuit lever
(left handlebar)
(2) Pull clutch lever
(left handlebar)
(3) lock clutch lever with pawl
(left handlebar)
(4) Set speed control l
ever to max
(right handlebar)
(5) Pull rope hard and fast to start
the engine
(3) Let rope glide back
carefully do not let snap
Pull and lock clutch
(for reference see start)
Set speed control to “STOP”
(right handlebar)
Emergency stop
release the safety lever

5500 CT
Quick start guide
5500 644 Page 4 of 7 998 592a_GB 08.10
Operations
Wear individual safety equipment like safety shoes and ear plugs !
Changing gears 1-4 and F/R requires pulling the clutch ! Do not shift the gears by force .
If necessary pull and release the clutch to bring the gears in easy switchable position !
Direction of motion forward / reverse (right handle bar)
! The gears must only be changed by pulling the clutch! (For drive and stop please see next chapter)
Drive and Stop
Hold safety lever, pull clutch
(left handlebar)
Choose gear with the shift rod
gears 1/2/0/3/4=1,0/1,5/0/
1,9/7,1 km/h
(left side)
For F/R motion
please see next chapter
(right handlebar)
Hand lever released
= forward
motion
Hand lever pulled
= reverse motion
Set speed control to max
move lever forward
(right handlebar)
Release the clutch slowly
Tool carrier moves
(left handlebar)
Pull clutch
tool carrier stops
(left handlebar)

5500 CT
Quick start guide
5500 644 Page 5 of 7 998 592a_GB 08.10
Differential Lock (right handlebar)
Release throttle and discharge drive for easy on/off switching the differential Lock
Move the machine with the engine switched off
Adjustment on Hand Levers
Check clutch play or adjustments each time you operate the machine; if necessary readjust!
Too much clutch play = machine and PTO don’t stop when clutch lever is pulled
Too little clutch play = machine doesn’t run; clutch slips while operating!
Dif
ferential Lock engaged =
improved traction
forward and reverse
Differential Lock disengaged
=
easy steering especially to turn
over
Set pawl to disengage Differential
Lock permanently
(1) Pull and lock clutch
(left handlebar)
(2) Look for neutral position
between 2 and 3 gear
(shift rod
)
(3) Disengage differential lock
for easy steering
lock lever with pawl
(right handlebar)
Clutch play 3-5mm
Turn threaded bolt in order
to adjust clutch play
(for more details see operation
manual page 35)
Pull clutch lever up to pressure
point
!

5500 CT
Quick start guide
5500 644 Page 6 of 7 998 592a_GB 08.10
Coupling and decoupling Implements
Mount and dismount attachments only with engine switched off !
PTO shifting
Shifting PTO requires pulling the clutch! Do not shift the PTO by force or without pulled clutch!
If necessary pull and release the clutch to bring the gears in easy switchable position!
1. Disconnect PTO shaft (attachment)
= move lever (4) to pos. “0”
2. Ensure clean surfaces
Slide pegs (2) of tool carrier
into hooks (3) of attachment
make sure attachment is properly
centred
and flat fitted
Fold both eye bolts (1)
over coupling flange
tighten cap nuts evenly
Connect fork end of shift rod
and shift lever with screw and bolt
(do not pull tight for free move)
To disconnect PTO shaft,
pull
lever
To connect PTO shaft,
push
lever

5500 CT
Quick start guide
5500 644 Page 7 of 7 998 592a_GB 08.10

agria-WerkeGmbH
Bittelbronner Straße 42
D-74219Möckmühl
Tel. +49/ (0)6298/39-0
Fax [phone]
e-mail: [email protected]
Internet: www.agria.de
Your local agria specialist dealer: