Agriframes 30546-TBK User manual

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ
Orderline: 0117 934 1790 Fax: [phone]
Order on-line: www.agriframes.co.uk
Product code: 30546-TBK
Description: Classic Round Gazebo Matt Black 1.8m
Quantity
Component
16
Uprights with one reduced end
8
Top Curves -1/4 Circle with straights (one reduced end)
4
Top ½ Circles with short Straights (two plain ends)
4
Stafford Hoop Halves (two plain ends)
16
Spacer Bars with Ring Clamps
1
Hole Maker
Quantity
Optional Component
8
Lattice Panels (4 x 3)
64
Reusable Cable Ties
Code
Description
Drawings
Quantity
Spare Grub screws (in a separate bag)
24
AGR-A610/40
5/8" Moisture Seal Black
24
AGR-A610/05
3/4" End Plug Black
16
AGR-A70/006
3mm Allen Key
1
AGR-A622/03
3/4”x3/4” Parallel Clamp (in 2 halves)
12
AGR-A74/002
M4 x 20mm Socket Cap Head Screw St/Steel
24
AGR-A72/001
M4 Hexagon Full Nut Stainless Steel
24
AGR-A75/000
M4 Form A Washer St/Steel
24
Please read the assembly instructions carefully prior to construction.
Tips:
Before positioning the Spacer Bars on the uprights, half screw in the grub screws to the Ring Clamps on the Spacer Bars, to
reduce the risk of losing the screws.
Once correctly positioned tighten the grub screw to secure the spacer bar to the uprights.
Positioning of the Spacer Bars
In many cases the position of the horizontal bars is down to personal preference. However, if you have the lattice option you
will need to leave the correct distance between bars.
Lattice Panel Option
For illustrative purposes we have only shown one side fixed with the lattice panels. Attach panels to both sides as you proceed.
Issues:
If you are experiencing any issues with your Agriframes product please contact our customer services team on 0117 934 1790
and quote your order reference.
WARNING: Contains small parts, tools and plastic bags. Keep children away until the unit is assembled and everything is cleared
away.
NOTE: The card, paper sack, and polythene bags are recyclable - please dispose of carefully.
MISSING PARTS PROCEDURE: Please call our customer service team on 0117 934 1790 and quote your order reference and
quote the missing part. E.g. ASO-----, 2 uprights missing.

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ
Orderline: 0117 934 1790 Fax: [phone]
Order on-line: www.agriframes.co.uk
Assembly Instructions Classic Round Gazebo Matt Black 1.8m
Product code: 30546-TBK
Please read these instructions carefully.
Step 1:
Slide a moisture seal onto the reduced ends of the Top (1/4 circle) Curves, then connect a ½
Top Circle onto the reduced ends of the curves. Cover the joins between the curves with
moisture seals.
Slide 2 Spacer Bars onto the ends of the Top
Curves, as shown in figure 1.
Position one of the Spacer Bars, 1”from
the joint of the curves.
Position the second Spacer Bar
approximately 5” from the end of the
Curves (41”from the other spacer bar).
Repeat this process until there are 4 sets of full
curves created.
Step 2:
Using 4 Parallel Clamps connect the ½ Top circles
together, as shown in Figure 2.
The easiest way to ensure that the full curves are
connected evenly is to have one or 2 people align the
curves to form the shape shown in figure 2, with the
straight part of the curve resting on the floor. Once the
curves are held in position another person should
connect the top curves at the 11 and 1 o’clock
positions, using the parallel clamps.
Once completed the curves will form a
structure as shown in Figure 3.
Assembly requires: A Rubber Mallet, an Allen Key (provided), a Ladder, a Spirit Level, Pliers, a Tape
Measure and at least 2 people.
Figure 1: Connecting Top Circles and Top curves
Figure 2: Aerial View of the Gazebo Full Curves
Connecting
Figure 3: Gazebo Curves once connected

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ
Orderline: 0117 934 1790 Fax: [phone]
Order on-line: www.agriframes.co.uk
Step 3:
Tap an end plug
into the ends of
the Stafford
curves, repeat
this action with
all 4 Stafford
curves.
TEMPORARILY attach, using Parallel Clamps, the Stafford Curves in the gaps between the
Top Curves. The Stafford Curve should be positioned in below the spacer bar on the Top
Curve as illustrated in Figure 4.
Please Note: once the top of the Gazebo has been placed onto the uprights the
Parallel Clamps connecting the Stafford Curves will need to be lowered. The Stafford
Curves will sit approximately 2”below the join of the
Curves and Uprights.
Ensure that once you have completed the construction of the
Gazebo top, that you check the distance between the ends of
the curves are equal.
If the distances are not equal adjust, as necessary, the
clamps’ positioning on the ½ Top Circles (refer to
Figure 1), and tighten the clamps.
Step 4:
Move the Gazebo top to where the structure will be installed and firmly push the structure
into the ground to make an impression or mark in the ground. These impressions indicate
where the uprights need to be inserted.
Step 5:
Using the Hole Maker make holes 15” deep, where you have marked the ground previously.
Ensure the holes are vertical and to the same depth.
Step 6:
Tap an end into the non-reduced end of the 8 upright poles, and insert these tubes (end
plugs facing down) into the holes. Slide a spacer bar onto the reduced end of the uprights
and then partially tighten the grub screw.
Slide a moisture seal over the reduced end of the upright.
Connect the remaining uprights onto the inserted uprights, cover the join between the 2
tubes with a moisture seal.
Step 7:
*If you have chosen not to include the lattice option you may place these Spacer Bars to
suit.
Figure 4: Positioning of the Stafford Curves
Figure 5: Aerial View of
Completed Gazebo Top

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ
Orderline: 0117 934 1790 Fax: [phone]
Order on-line: www.agriframes.co.uk
*If the lattice option has been chosen you will need to follow the spacing guide for the
lattice, to ensure that the lattice fits into the spaces.
Slide 2 Spacer Bars with Ring Clamps onto each pair of uprights, tightening the grub screws
once the Spacer Bars as positioned as illustrated in Figure 6.
The lower Spacer Bars should be positioned 9 inches from ground level (once the
uprights have been inserted)
Position the Second Spacer Bar 40 inches above the lower Spacer Bar.
Also check the positioning of the Spacer
Bars on the Gazebo top, as shown in
Figure 6.
Step 7:
Lift the constructed Gazebo top onto
the uprights, then cover the joins with
moisture seals.
You will need at least 2 people
for this step due to the weight of
the Gazebo top.
Step 8:
Reposition the Stafford Curves
Loosen the Parallel Clamp Joint, lower the Stafford Curves until the Parallel Clamp
sits 2 inches below the join between the Upright and the full curve.
Move the Parallel Clamp position of the Stafford Curve, until the Parallel Clamp holds
the Stafford curve approximately 2 inches from the end of the curve.
If you have any questions regarding assembly please call our customer service team on 0117 934 1790
Figure 6: Round Gazebo Spacer Bar Distances