Agriframes 40136 User manual

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ
Orderline: 0845 260 44 50 Fax: [phone]
Order on-line: www.agriframes.co.uk
Assembly Instructions for 6ft Classic Extra Monet Arch
Product codes: 40136
Please read these instructions carefully. They are designed to make assembly quick and easy. Please check you
have received all the components and refer to the diagrams.
Tools Required
Rubber mallet (or similar)
Tape measure
Spirit level
Phillips screwdriver
Club hammer (or similar)

Parts List
Code Quantity Component
A90116
1
Assembly kit (see check list)
A44017
2
Monet
curve
(plain ends)
A44018
2
Monet curve
(
reduced one end)
A40012
4
84” uprights
A30005
8
22 ½” spacer bars
A42007
1
Holemaker
Quantity Optional Component
2
Lattice panels
5
cells high x 4 cells wide
2
Lattice panels 4 cells high x 4 cells wide
24
Lattice ties
Assembly Instructions
1. Preparation
1.1. Take the four uprights and tap an end plug into the standard end of each.
1.2. Place two screws in each T joint as shown, but only tighten the screws enough to
hold them in. Make sure the screw points do not protrude into the inside of the joints
as they will scratch the coating when they are attached to the tubes. Note that the
third screw hole in the joints will be used during final assembly.
1.3. Take the eight 22½” spacers. Push T joints onto both ends of all of them. Lay each
assembly flat to ensure the joints are parallel as shown below then measure the
exposed tube and ensure that it is 18½” long. If the measurement is greater than this
you will need to use a rubber mallet to knock the joints home.
2. Assembling the roof section
2.1. Take the two Monet curves with plain ends, the two
Monet curves with one reduced end and two of the
22½” spacer bar assemblies. Refer to the diagram.
Slide a spacer onto the horizontal section of the two
Monet curves with a reduced end, connecting them
together so that they are parallel. Repeat for the plain
ended curves.
2.2. Refer to the diagram below. Take two 1” moisture
seals and two of the 22½” spacers. Slide a moisture seal onto the two reduced tube ends and connect
the two roof halves together. Ensure that the joins are covered by the moisture seals. Slide a second
spacer assembly onto each side of the roof section. Position the spacers according to the measurements
in the diagram at the end of the instructions.
2.3. Measure the diagonals of the roof section to ensure it is square and adjust if necessary.
18½”

3. Site preparation
3.1. Place the roof structure in the site that you intend to install
the arch and mark the positions of the four uprights.
Remove the roof section and use the Holemaker to make
15” deep holes at each of the marks. Ensure that the holes
are all vertical and the same depth.
3.2. Place one of the uprights in each hole and ensure that the
tops are level. Adjust if necessary.
4. Final assembly
4.1. Slide two of the remaining spacer bar assemblies onto
each pair of uprights. Attach the first 14” above the
ground and the second 50” higher.
4.2. Slide a moisture seal onto the top of each upright and lift
the roof section onto the uprights. Once it is attached
securely slide the moisture seals up to cover the tube
joins.
4.3. Place a third screw in each T joint. Check that all the
measurements are correct and then fully tighten all joints
and screws.
4.4. If you purchased the lattice infill it can be attached to the
structure, between the horizontal spacers, using the ties
provided.
PACKING REFERENCE:

AGRIFRAMES KIT COMPONENT PACKING CHECK
LIST
Code/Product
Number 40136
Description 6ft Monet Arch (CLX)
Kit Component
Details Kit Number as referred to in main instructions 90116
Code Description Drawings Quantity
AGR-A610/29 1x7/8" T-Connector Joint Black 16 Checked
AGR-A73/009
No 10x1/2" Pozi Pan S/Tapp AB Screw
BZP 48 Checked
AGR-A610/38 1" Moisture Seal Black 6 Checked
AGR-A610/08 1" End Plug Black 4 Checked
Authorised Packing Stamp:
Customer
Note:
In the unlikely event that there is any of the above components missing or are faulty
please contact our
Customer Helpline Number on 0845 260 44 50 and where possible quote the component
code number
to help us deal with your query promptly.
PACKING REFERENCE: