Aiphone RY-18L User manual

- INSTRUCTIONS -
Form C Relay for 12-18V DC Intercom Systems with Door Release
WIRING DIAGRAMS:
MK-SERIES BLACK & WHITE VIDEO SYSTEM
Page 1
INSTALLATION:
1. Install in a suitable location, either near the power source for the door release mechanism, or behind the intercom.
2. Secure wire connections with proper termination, such as wire nuts or crimp connectors.
3. Trim the wires to the desired length.
4. Cut the unused contact wire so the bare strands are not exposed.
A1
A2
B1
B2
S
S
DC 18V
+
-
DR REL
L
L
MK-1GD
MK-2MCD
MK-Series
Door Station
A1
A2
PS-1820UL
+
-
.
Red
Gry
Brn
Org
Yel
COM
N/O
N/C
+ -
Use Normally Open
contact for electric strike
RY-18L COLOR CODE:
Input of Relay:
Red:L/RED, Postive trigger
Gray:(-) NEGATIVE
Output of Relay:
Brown:COMMON
Orange: N.O. Contact
Yellow:N.C. Contact
(See contact rating specs on
back page)
The RY-18L Door Release Relay Module is an interface between the door strike contacts on the Aiphone unit and the
actual release mechanism. The contact ratings on Aiphone units vary, and are all Normally Open. If your strike or
maglock is a higher voltage or draws more current than specified for the unit, the RY-18L is required. It provides either a
Normally Open contact for an electric strike, or a Normally Closed contact for a magnetic lock. The contact rating
supports a majority of door release hardware available on the market. This relay is recommended with all MK and JF
systems when using the single door release feature, and for the LEM-1DL or LEF systems when connecting a maglock.
Add
jumper
wire
from L
to +
MAGNETIC LOCK WIRING METHOD:
(Normally Closed contact)
Lock Power: Power source for Magnetic Lock
When using 12-18V DC power, use the RY-18L.
When using 24V DC power, use the RY-24L.
LE-Series Sub 1
E
+
-
EL
EL
LEM-1DL
~
~
PT-1210N
1
E
-
Leave jumper
between E and -
attached
Red
Gry
Brn
Org
Yel
COM
N/C
Use Brown & Yellow wires
when connecting to Maglock.
LOCK
POWER
RY-18L
Magnetic Lock
RED: L/RED
BLK: (-) Neg.
BRN: Common
ORG: N.O.
YEL: N.C.
+
-
LOCK
POWER

NOTE:
Release contacts on the JF-2MED are from
4-pin connector included with unit. Connect
Red & Brown wires as shown. Orange &
Yellow wires are not used.
Release contacts on the JF-1MD are L/L
terminals.
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]
TOLL FREE TECHNICAL SUPPORT: [phone]
TOLL FREE FAX LINE: [phone]
E-MAIL: [email protected] RY-18L Instr.
0307JD
SPECIFICATIONS:
Power Source: Supplied by master station
Mounting: No mounting required
Terminations: Color-coded prewired pigtails
Relay Input: 12-18V DC, Red, Gray wires, 22AWG
Relay Output: Brown, Red, Orange wires, 18AWG
N/O Output rating: 5A at 30V DC
10A at 125V AC
3A at 250V AC
N/C Ouptut rating: 3A at 30V DC or 125V AC
Wiring: 2 conductors from monitor's door release contacts to RY-18L.
2 conductors from RY-18L to strike, with power for strike wired in series.
Dimensions (HxWxD): 1-3/4" x 7/8" x 7/16", with wires extending approx. 7-1/2"
WIRING DIAGRAMS:
A1
A2
B1
B2
S
S
DC 18V
+
-
RELEASE
(L)BRN
(L)RED
JF-1MD/
JF-2MED
JF-DA
JF-DV
JF-DVF A1
A2
PS-1820UL
+
-
.
Red
Gry
Brn
Org
Yel
COM
N/O
N/C
Use Normally Open
contact for electric strike
ELECTRIC STRIKE
WIRING METHOD:
JF OPEN VOICE COLOR VIDEO SYSTEM:
PS-1820UL
+
-
.
Red
Gry
Brn
Org
Yel
COM
N/O
N/C
Use Normally Closed
contact for magnetic lock
MAGNETIC LOCK
WIRING METHOD:
A1
A2
B1
B2
S
S
DC 18V
+
-
RELEASE
(L)BRN
(L)RED
Add
jumper
wire from
BRN to +
Add
jumper
wire from
BRN to +
NOTE:
Only wiring pertaining to connection of door
release relay is shown here.
For complete system information, please
consult the main system installation manual.
JF-1MD/
JF-2MED
+ -
LOCK
POWER
+ -
LOCK
POWER