Airflow SunShine Threesome 6500A Installation guide

Clipsal Australia Pty Ltd
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
IMPORTANT
THESE INSTRUCTIONS ARE ALSOYOUR
INSTALLATION TEMPLATE
Installation Instructions and Warranty
Radiant Globe Combination
Heater, Light and Exhaust Fan
Threesome 6500A
FITTING INSTRUCTIONS
Thank you for purchasing this Threesome product by Clipsal Australia Pty Ltd. Threesome
combines heat globes, an exhaust fan and light, providing gentle radiant heat, clean air and
a bright light from one compact, stylish unit. All functions are separately controlled from a
supplied switch plate for convenient fingertip control.
You can be assured of years of trouble free operation by installing your Threesome carefully
according to instructions. Please read all instructions before commencing installation.
Threesome can be mounted in any room that requires instant, direct, radiant heat to ward
off winter chills. The light and fan have separate switching, making it suitable for bathrooms,
dressing and change rooms.
Threesome
IMPROVED DESIGN now with ceramic lamp holders and
compact fluorescent lamp
WARRANTY
Clipsal Australia Pty Ltd warrants your product to be free from defects in material and
workmanship for a period of five (5) years from the date of purchase.The Warranty applies
only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, Clipsal Australia’s only obligation, and
your exclusive remedy, is the repair or replacement of the product at Clipsal Australia’s
discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alteration, neglect or mishandling (excluding any labour cost relating
to removal or reinstallation of product and transport cost). This Warranty shall not apply
to any product, which is found to be improperly installed, setup or used in any way not in
accordance with the instructions supplied with the product. This Warranty shall not apply to
any batteries used in the product or to any damage caused by such batteries.
Heater globes supplied with this unit are covered by a separate two (2) year replacement
warranty and excluded from the five (5) year in-home warranty. The Phillips 11W Ambiance
Screw in Reflector R63 Energy Saver Globe (CFL) is excluded from all the above warranties.
If your product fails to operate satisfactorily, please return it to the point of purchase or
Clipsal Australia Pty Ltd.
CLIPSAL AUSTRALIA PTY LTD DOES NOT WARRANT AND SPECIFICALLY
DISCLAIMS ANY WARRANTY, WHETHER EXPRESSED OR IMPLIED, OF FITNESS
FOR A PARTICULAR PURPOSE OTHER THAN THE WARRANTY CONTAINED HEREIN.
NOT IMPLIED WARRANTY ON THIS PRODUCT, CREATED BY STATE LAW, SHALL
EXTEND BEYOND THE TERM OF THIS WARRANTY UNLESS SUCH LAW OTHERWISE
PROVIDES. CLIPSAL AUSTRALIA PTY LTD SPECIFICALLY DISCLAIMS ANY
LIABILITY AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
LOSS OR DAMAGE, INCLUDING, BUT NOT LIMITED TO, DAMAGES TO ANY
EQUIPMENT WITH WHICH THIS PRODUCT IS USED.
No agent, representative, dealer or employee of the company has the authority to increase or alter the
obligations or terms of this warranty. Clipsal Australia Pty Ltd reserves the right to change specifications
or designs described in this manual without notice and without obligation.
IMPORTANT: RETAIN YOUR RECEIPT. To obtain in-home service under warranty you must
retain your original purchase receipt. Service will otherwise be charged at current rates.
For your future reference, please complete the following details and file this
information with your purchase invoice.
Threesome Model 6500A
Serial Number
Purchased From
Date of Purchase
Made in
PRC
SPARE PARTS
Electrical switches supplied with your Threesome are usually available from any electrical
wholesaler. The central globe can be replaced by Phillips 11W Ambiance Screw in Reflector
R63 Energy Saver Globe (CFL). The special Hard Glass heating globes are only available
from selected retailers and wholesalers.
Note: Maximum wattage of central light globe is 100 watts.
Maximum wattage of each heat globe is 275 watts.
SERVICE AND MAINTENANCE
For service and maintenance please call the National Customer Service number on
1300 2025 25.
TM
F914/06
CLIPCOM 20261 October 2009
Clipsal Australia Pty Ltd reserves the right to change specifications, modify
designs and discontinue items without incurring obligation and whilst
every effort is made to ensure that descriptions, specifications and other
information in this catalogue are correct, no warranty is given in respect
thereof and the company shall not be liable for any error therein.
© Clipsal Australia Pty Ltd.The identified trademarks and copyrights are
the property of Clipsal Australia Pty Ltd unless otherwise noted.
clipsal.com

SUITABLE LOCATIONS
The Threesome has been designed specifically for cavity type ceilings. Flat roof installation is
NOT recommended.
Threesome must not be mounted in areas subject to direct splashing. Threesome must
be mounted in the horizontal position only. Unsuitable for ‘cathedral’ or ‘raked’ ceilings.
Threesome comes with four infrared heat globes which emit harmless radiant heat.
Threesome is best positioned directly above the area requiring warmth. Before you start,
make sure your ceiling has at least 280mm clearance from the roof.
WHERE TO LOCATE
Radiant globe heaters are not designed to heat entire rooms. They provide instant,
concentrated heat to persons standing directly below the heat lamps. Therefore, units should
be located over the area where drying off takes place, not directly over a shower
or bath.
These heaters are not designed to be left on for extended periods of time, as this could
cause overheating and premature failure. Threesome units, even those without fans, should
not be covered or installed in situations which restrict the natural ventilation of the units for
cooling purposes. For applications where the heat lamps may be left on for periods longer
than 20 minutes, it’s recommended that a seperate timer is installed to automatically turn off
the heat lamps.
Ceiling insulation should be kept well clear of the units (at least 100mm). For optimum
performance, models with exhaust fans should be installed in areas with good ventilation,
to enable fresh air to flow into the room. It is recommended that there is at least a 500mm
clearance above the unit, and that the ceiling space is adequately ventilated to allow
appropriate air flow through the unit. Any restrictions on return air entering the room, or
exhausted air escaping from the ceiling space, will impair effectiveness and may contribute to
premature failure.
RADIANT HEAT
Threesome requires no warm up period because of its efficient, radiant heat globes. Heat is
directed at you for an instant warmth you can feel, rather than gradually warming the entire
room. Because of this, Threesome only needs to be turned ON when you are in the room.
MOUNTING
1. Using this card in its open state as a template, position it
in the area you want your Threesome and draw around
the edges with a pencil to mark the hole cutting size.
BE SURE TO CHECK ABOVE THE CEILING FOR
MINIMUM SPACE OF 280mm (for optimum performance
allow 500mm or more clearance) AND THE LOCATION
OF THE CEILING JOISTS. Ensure there is a minimum
of 100mm clear space between the Threesome unit and
any ceiling insulation.
2. Use a saw to cut the section along the drawn lines.
3. The lamp surround easily unclips from the main body by
lifting gently from any side. Remove it and the four heat
globes to avoid damage from knocks and vibrations.
Now insert your Threesome with both side springs pulled
inwards so that the body can pass through the hole
without damaging the plaster. Return springs to original
position to fix body securely to the ceiling.
NOTE: Springs are adjusted to suit either 10mm or
13mm plasterboard ceiling.
4. Clip the lamp surround back onto the body making sure
both clips snap into place. Fit retaining spring as shown
in diagram.
5. The lamp surround has been shaped to position heat
globes correctly in the main body. Screw the four, large
heat globes through the lamp surround holes, tightening
firmly to ensure a good electrical contact. DO NOT
FORCE OR OVER-TIGHTEN. Screw centre light globe
into place. Centre lampholder is designed to accept 100
Watt (max), reflector type, R63, screw in light globes.
PERMANENT
APPLIANCE
WIRING
E
NEUTRAL
HEAT
HEAT
LIGHT
FAN
SWITCHES EARTH
ACTIVE
3. Remove screws from terminal cover on the Threesome and put aside. Wire according
to the label beside the terminal strip. Once the wires are connected incoming
cable must not be fouled by cover. Use appropriate knockouts in terminal cover to
accommodate cable before replacing. Screw down firmly.
TEST
Clean surround and globes with a soft, moist cloth. Check power is switched on and all
switches activate properly, according to their marked function.
CLEANING
• Ensure the Threesome is switched off before cleaning.
• Remove globes when they are at room temperature. Wipe with a damp cloth, never immerse.
• Unclip lamp surround and wash in warm, soapy water. Always use a soft cloth, never abrasives.
• Clean away any excess fluff from the inside of the body, motor blade brackets.
IMPORTANT SAFEGUARDS
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Ensure that the switch is in the off position when changing the heat lamp (globe) or light globe.
• Ensure that the wattage of a replacement globe is the same as the globes supplied with the unit.
• Ensure the grille is free of objects, dust build up, etc. Make sure that the air flow through the
grille is not inhibited.
• Do not install close to curtains and other combustible materials.
• The appliance shall, under no circumstances, be covered with insulating material or
similar material.
• Regulations concerning the discharge of air have to be fulfilled.
• Joists, beams and rafters shall not be cut or notched to install the appliance.
ELECTRICIANS’WIRING INSTRUCTIONS
Your Threesome requires a 230-240 Volt, 50Hz electrical supply. All electrical work must
be carried out by a qualified electrician and installed in accordance with relevant Electrical
Wiring Regulations.
Your new Threesome comes with all required switches and mounting plate.
WIRING DETAILS
1. Decide the best position for the switch set and mount it. Be sure to click the switches into
the backing plate in the desired order beforehand.
2. Connect wiring to switches as shown in the appropriate electrical diagram.
N
H
H
L
F