Airflow 7106A User manual

MaxAir Wall
Exhaust Fan
7106A Auto Switched and
7108A Pull Cord Switched
Installation Instructions/Warranty Card

7106A and 7108A MaxAir Wall Exhaust Fan Installation Instructions/Warranty Card
© Clipsal Australia Pty Ltd
2 of 4
Check that the proposed location of the1.
fan will not foul joists, existing wiring or
other internal wall features (wall thickness
between 110 and 310mm). Use template
provided to mark out hole. Cut a hole
through the wall ø230mm. Screw fan
assembly to internal wall via four corner
openings, see Figure A, (appropriate
fasteners to be used for each installation
not provided).
2. Remove termination cover see Figure B,
(screws marked with ‘1’, ‘2’, ‘3’).
4. With fan assembly mounted on the internal
wall, cut PVC sheet to suit wall depth.
7106A Connection Diagram
External
Isolating Switch
External
Isolating Switch
7108A Connection Diagram
1
2
3
Figure A
Figure B
Fan
Assembly
Screws
labelled 1, 2,
3, retain the
terminal cover
to the chassis.
3. Electrician to make electrical connections
as shown, using three core, 1mm2cable.
Replace termination cover.
Figure C
MOTOR
MOTOR
YL
YL
A/P
A/P
RD
RD
N
N
GR
GR
E
E
1
1
2
2
BK
BK

7106A and 7108A MaxAir Wall Exhaust Fan Installation Instructions/Warranty Card
© Clipsal Australia Pty Ltd 3 of 4
5. Coil the cut PVC sheet around
the wall grille outlet spigot and
slide into retaining clips.
6. Screw wall grille outlet to
external wall (appropriate
fasteners to be used for each
installation not provided).
7. Place cover assembly, as shown, over fan
assembly and tighten retaining screw.
Test. Ready to go.
WARNING:
The appliance is not intended for use by
young children or infirm persons unless
they have been adequately supervised by a
responsible person to ensure that they can
use the appliance safely.
Young children should be supervised to
ensure they do not play with the appliance.
Appliance intended to be mounted on
external wall only.
Ensure the fan is switched OFF from the
supply mains before removing the guard.
NOTE: SHUTTER OPERATION
Do not turn auto switched models on
without the front cover fitted. Auto
switched fans are fitted with a thermal
actuator, thus requiring approximately
three minutes to fully open and
approximately sixty seconds to close
shutters. Pull cord models are operated
either by the built in pull cord and/or
separate switch (thermal actuator). If it
is decided to use and operate fan via a
separate switch, the delay on opening and
closing of shutters must also be noted.
HOLE CUT-OUT TEMPLATE
HOLE CENTRE ø230mm
Internal External
Wall Grille
Outlet
Wall
Grille
Outlet
Sticky
Tape
(optional)
Sheet to
be approx.
20mm
overlapping
duct
Fan
Assembly
Cover
Assembly Retaining
Screw
Fan
Assembly

F1698/03 CLIPCOM 19005 April 2009
Clipsal Australia Pty Ltd reserves the right to change specifications,
modify designs and discontinue items without incurring obligation
and whilst every effort is made to ensure that descriptions,
specifications and other information in this catalogue are correct, no
warranty is given in respect thereof and the company shall not be
liable for any error therein.
© Clipsal Australia Pty Ltd. The identified trademarks and copyrights
are the property of Clipsal Australia Pty Ltd unless otherwise noted.
Product of Clipsal Australia Pty Ltd
A member of Schneider Electric
Contact us: clipsal.com/feedback
National Customer Care Enquiries:
Tel 1300 2025 25
Fax 1300 2025 56
clipsal.com
Warranty
The Airflow Wall Exhaust Fan and related products are guaranteed for three (3) years.
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the
product which the consumer has under the Trade Practices Act and similar State and Territory Laws.
The original purchaser of this Airflow Wall Exhaust Fan is provided with the following warranty, subject
to the following conditions. Clipsal Australia Pty Ltd warrant this product for a period of three years
from the date of purchase for all parts defective in workmanship or materials. All defective parts will be
replaced free of charge. The following exclusions do not preclude the purchaser from those statutory
rights consumers have under the Trade Practices Act or similar State and Territory Laws.
Warranty Conditions
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person
and must be connected to the voltage requirements as specified on the ratings label.
4. The manufacturer does not accept liability for any direct or consequential damage,
loss or other expense arising from misuse or incorrect installation and operation of
the appliance.
5. Warranty will only be given on appliances where proof of purchase date is provided
eg. original invoice or copy.
As a record of your purchase, please fill out the following details and file this information with your
purchase invoice.
Airflow Model Number: ...................................................................................................................
Serial Number: ...............................................................................................................................
Purchased from: .............................................................................................................................
Date of Purchase: //