AirLive WT-2000ARM User manual

WT-2000ARM
Turbo-G Wireless ADSL 2/2+ Router
Quick Setup Guide
1
24
English ●●
Polski ●●
Deutsch ●●
Español ●●
Czech ●●
Slovensky ●●
Português ●●
Russia ●●
9
32
40
48
N
ote: During firmware upgrade, please do not close the
web browse or turn o
ff
the
p
ower
f
or 5 minutes.
56
17

1
1
Turbo-G Wireless ADSL 2/2+
Router
Important Information

 The Router mode’s default IP address is 192.168.2.1

 The default Subnet Mask is 255.255.255.0

 The default login name is admin

 The default password is airlive

 The default SSID is airlive

 The default Channel is 6

 Please use only the power adapter provided with the Router
LED Indicators
WT-2000 ARM
LED Status
Indicator Color ON Flashing
Power ●Green Power on -
ADSL ●Green Link
established -
WLAN ●Green - Wireless
Sending/Receiving
LAN ●Green - LAN Sending/Receiving
English
English

2
2
Turbo-G Wireless ADSL 2/2+
Router
Auto Setup Wizard
Interenet: Basic Setting
This setup wizard can be run in Win 98SE/Me/2000/XP. Please make sure
that you have connect your PC to the LAN port of the ADSL router, the
ADSL line is connected to the router before using the Setup Wizard.
1. Please insert the driver CD that came with your device into your
CD-ROM drive, the driver CD will auto start and show the installation
guide. If not, please double click the CD-ROM device icon in "My
computer", and execute the Run.exe.The following screen will be
displayed. Click “Setup Wizard”.
English
Installation Steps
1. Please install your network cards first before the Router
2. Screw-in the antenna (clockwise) into the Antenna connector
3. Connect the power, LAN cable and ADSL cable to the back
4. Use your wireless card to do a site survey, the default ADSL SSID is
“airlive” and Channel is “11”
5. If you need to change router configuration, please follow the
procedure below:
The Router default IP address is 192.168.2.1. Please make
sure your computer IP is in the same subnet as the AP (i.e.
192.168.2.x)
Open the web browser and enter 192.168.2.1. When asked
for Login and Password, just type admin for loginname and
airlive for Password.
English

3
3
Turbo-G Wireless ADSL 2/2+
Router English
English
2. This wizard will be executed and try to search for the ADSL
Router.

4
4
Turbo-G Wireless ADSL 2/2+
Router
4. Please select the country you have installed the ADSL
router and click “Next”.
English
English
3. If the router cannot be found, please enter the IP Address and the
Password of the router to search again. Click “Next” to continue.

5
5
Turbo-G Wireless ADSL 2/2+
Router
English
English
5. Please select the ISP (Internet Service Provider) of your
ADSL service.
6. Enter the Username and Password which your ISP has
provided to you if it is needed. Click “Next”.
If your country or ISP is not in the wizard.
Please go to “Manual setup wizard” section for
installion instruction.
!

6
6
Turbo-G Wireless ADSL 2/2+
Router
English
7. Click “Save” to save the settings and reboot the router.
8. The ISP Setting are all finished. If your want to configure
more settiungs. Please Click “Advanced Settings” or click
“Finish” to close the wizard
English

7
7
Turbo-G Wireless ADSL 2/2+
Router English
English
Once your Pc has obtained an IP address from upir router, enter default ip
address 192.168.2.1 (router’s IP address) into your PC’s web browser and
press <enter>
Manual Setup Wizard
The login screen below will appear. Enter the “User Name” and
“Password” and then click <OK> to login. By default the user name is
“admin” and the password is “airlive”. For security reasons it is
recommended that you change the password as soon as possible.
The HOME page screen below will appear. The Home Page is divided into
seven sections: Quick Start, Interface Setup, Advanced Setup, Access
Management, Maintenance, Status and Help.
1. Select the Quick Start menu, then click “Run Wizard” to start the
configuration.

8
8
Turbo-G Wireless ADSL 2/2+
Router
ME
M
O
English
English

9
9
Turbo-G Wireless ADSL 2/2+
Router
Turbo-G Wireless ADSL
2/2+ Router Polski
Ważne Informacje

 Domyślnie adres IP to 192.168.2.1

 Domyślnie maska podsieci to 255.255.255.0

 Domyślnie login name to admin

 Domyślnie password to airlive

 Domyślnie SSID to airlive

 Domyślnie kanał11
Wskaźnik LED
WT-2000 ARM
LED Status
Wskaźnik Kolor Światło stałeŚwiatło błyskające
Power ●Zielony Zasilanie
włączone -
ADSL ●Zielony Połączenie
ustanowione -
WLAN ●Zielony - Bezprzewodowe
wysyłanie/odbieranie
LAN ●Zielony -
Wysyłanie/odbieranie
poprzez przewodową
siećLAN
P
o
l
s
ki