AirLive SA-105 User manual

SA-105
Dual Relay Touch Wall
Switch
User Manual

Copyright and Disclaimer
i AirLive SA-105 User Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
This product contains some codes from GPL. In compliance with GPL agreement, AirLive
will publish the GPL codes on our website. Please go to www.airlive.com and go to the
"Support->GPL" menu to download source code.
All Trademarks are properties of their respective holders.

Copyright and Disclaimer
ii AirLive SA-105 User Manual
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Disposal
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.

1 AirLive SA-105 User Manual
Table of Contents
1. Overview................................................................................................... 2
1.1 Adding to Z-WaveTM Network ........................................................... 3
1.2 LED Indication................................................................................... 4
1.3 Choosing a Suitable Location............................................................ 4
1.4 Installation and Basic Operation........................................................ 5
1.5 Association and Parameter................................................................ 7
1.6 Specifications .................................................................................. 10

2 AirLive SA-105 User Manual
1
1. Overview
The SA-105, is a Z-Wave plus compliant Z-Wave Dual Relay Touch Wall Switch to replace
your current light switch with a Z-Wave included one. The Z-Wave command is translated
to a switching command. The wall mounted switch is a component of the lighting control
system. This wall mounted switch is designed to work with other Z-Wave enabled devices.
Z-Wave nodes of other types can be added to the system and act as repeaters if they
support this function of repeating the signal received to other modules in the system. As
part of a Z-Wave network, this switch will also act as a wireless repeater to insure that
commands intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the Z-Wave controller. There are no
field repairable assemblies on this unit. If service was needed, the unit must be returned
where purchased. This product can be included and operated in any Z-WaveTM network
with other Z-WaveTM certified devices from other manufacturers and/or other applications.
All non-battery operated nodes within the network will act as repeaters regardless of vendor
to increase reliability of the network.

3 AirLive SA-105 User Manual
1.1 Adding to Z-WaveTM Network
Connect switch to power source, after making it powered, please do not operate it
within 20s.
Note: This switch must be “Included in the Network” where it will be permanently installed.
The proper operation of the SA-105 in the mesh network is dependent on knowing its
location with respect to other nodes. You cannot “test bench” configure this switch and then
install it.
First time adding, When first power is applied, its LED flashes on and off alternately and
repeatedly at 1-second intervals. It implies that it has not been assigned a node ID yet and
start the auto inclusion. To add the device into the Z-WaveTM network, first make sure the
primary controller is in the inclusion mode.
1.1.1. Auto Inclusion
On the front casing, there is an On/Off touch button with LED indicator which is used to on
and off or carry out inclusion, exclusion, reset or association. When first power is applied,
its LED flashes on and off alternately and repeatedly at 1-second intervals. It implies that it
has not been assigned a node ID and cannot work with Z-Wave enabled devices. The table
below lists an operation summary of basic Z-Wave function. Please refer to the instructions
for your Z-Wave™ certificated primary controller to access the Setup function, and to
include/exclude/associate devices.
Note: Auto inclusion timeout is 2 minute during which the node information of explorer
frame will be emitted once several seconds. Unlike “inclusion” function as shown in the
table below, the execution of auto inclusion is free from pressing the Include/Exclude button
in on the front case.
The table below lists an operation summary of basic Z-Wave functions. Please refer to the
instructions for your Z-WaveTM Certificated Primary Controller to access the Setup function,
and to include/exclude/associate devices.
Function
Description
No node ID
The Z-Wave controller does not allocate a node ID to the
Switch
Inclusion (Add)
1. Have Z-WaveTM Controller entered Inclusion (Add) mode.
2. Touching the on/off button three times in rapid succession
within 1.5 seconds will enter inclusion mode.
Exclusion
(Remove)
1. Have Z-WaveTM Controller entered Exclusion (remove)
mode.
2. Touching the On/Off button three times in rapid succession
within 1.5 Press will enter exclusion mode

4 AirLive SA-105 User Manual
Node ID has been excluded.
Reset
1. Touch the On/Off button and hold for 10 seconds.
2. IDs are excluded.
Association
1. Have Z-Wave Controller entered association mode. Or
Touch the On/Off button three times within 1.5 seconds will
enter association mode
2. There are three groups for the switch (it can associate max
five devices).
1. Including a node ID allocated by Z-WaveTM Controller means “Add” or
“Inclusion”. Excluding a node ID allocated by Z-WaveTM Controller means
“Remove” or “Exclusion”.
2. Failed or success in including/excluding the node ID can be viewed from
Z-WaveTM Controller.
3. Association: it can be associated by Z-Wave devices with association
4. Use the"Reset" procedure only in the event that the network primary
controller is missing or otherwise inoperable
1.2 LED Indication
To distinguish what
LED Color
Led Display Status
Description
Blink 5 Times (1s Interval)
Light switch is powered on, and has not
been added to Z-Wave network
Blink 5 Times (500ms lnterval)
1: Enter lnclusion Mode,
2: Send Node lnfo
Red
Blink red color once then pink
color 4 times on and off
alternately
1:Enter Exclusion Mode
Blink 5 Times in 2s
Reset successfully
Always On
Back light is disabled and Relay is on
Blue
Always On
Back light is enabled and Relay is off
Pink
Always On
Back light is enabled and Relay is on
1.3 Choosing a Suitable Location
1. The SA-105 Z-Wave Wall Switch can replace your original Switch the location there for
would be the same as your original wall switch. Do not place the switch in a wet
environment.

5 AirLive SA-105 User Manual
1.4 Installation and Basic Operation
Step 1 Connection diagram of SA-105.
Note: A Neutral wire is required for the correct operation.
Step 2 Removal of front cover.
Carefully use a flathead screw driver to remove the front cover from the base. Do not use
force, as this could break the cover.
Output L1
Output L2
Live Wire (Input)
Neutral Wire (Input)

6 AirLive SA-105 User Manual
Step 3 Basic Operation
Basic Operation (Local Control)
The switch allows the user to:
-Turn ON or OFF the attached load.
-Include or exclude the module from the Z-Wave system.
-Control other Z-Wave enabled devices.
Also, when a controller prompts you to “Send Node ID” or to “Press Button on Unit” quickly
tap the switch On or OFF three times to satisfy those instructions.
-Tapping the left switch button turns the load attached to L1 ON/OFF.
-Tapping the right switch button turns the load attached to L2 ON/OFF.
Caution: Note: Upon restoration of power after a power loss, the switch returns to previous
known state.
LED Indication
The LED on the switch will change color when the load attached is turned on/off
Advance operation all on/all off
The switch support the all on/all off commands. The switch can be set to respond to all on
and all off commands 4 different ways. Refer to your controller for information on how to set
the switch to operate in the manner you desire. Some controllers may be only able to set
certain settings of all on /all off response. The 4 different ways the switch can be setup to
respond to all on and all off

7 AirLive SA-105 User Manual
1.5 Association and Parameter
1.5.1. Association Setup
Association
(Association Command Class Version 2)
This Light Switch supports 3 groups; each group supports max 5 associated nodes
GROUP 1: Is lifeline service that assigned to Light Switch status. It enables Light Switch to
send reports to Z-Wave Gateway whenever some button is touched. This Group
Support:SWITCH_BINARY_REPORT,
DEVICE_RESET_LOCALLY_NOTIFICATION
Notice: The SWITCH_BINARY_REPORT is sent only by
MULTI_CHANNEL_CMD_ENCAP command
GROUP 2: Allows Sending Binary Switch Report to associated devices in this group. This
group is mapping to Endpoint 1 This Group Support
SWITCH_BINARY_REPORT
GROUP 3: Allows Sending Binary Switch Report to associated devices in this group. This
group is mapping to Endpoint 2 This Group Support
SWITCH_BINARY_REPORT
1.5.2 Configuration Parameter
Configuration
Parameter
Function
Value
Default Value
Size (Byte)
1
Back Light Enable
0 - 1
1
1
2
Relay On/Off Indicate
0 - 1
1
1
3
Relay On/Off Status Saved
Enable
0 - 1
1
1
4
Root Device Mapped Setting
0 - 3
1
1

8 AirLive SA-105 User Manual
1.5.3 Parameter Description
Back Light Enable
-Parameter NO:1
-Length: 1 Byte
-Valid values=0 or 1 (default value is 1)
This parameter defines the back light state of touch button. The back light led would be on
when Light Switch is powered on if this parameter is set to '1', otherwise the back light led
would be off. The default value is '1’
Relay On/Off Indicate
-Parameter NO:2
-Length: 1 Byte
-Valid values=0 or 1 (default value is 1)
This Parameter defines the relays state. The led will be turned on with pink color when the
button is touched to turn on relay if this parameter is set to 1; otherwise the led state is not
changed. The default value is'1'.
Relay On/Off Status Saved Enable
-Parameter NO:3
-Length: 1 Byte
-Valid values=0 or 1 (default value is 1)
This parameter defines the on/off status of relay needs saving or not. The status will be
saved when relay status is changed if this parameter is set to '1'; otherwise the relay status
is not saved. The Light Switch will restore the relay On/Off status when is powered on again.
Root Device Mapped Setting
-Parameter NO:4
-Length: 1 Byte
-Valid values = 0 ~ 3 (default value is 1)
This parameter defines which endpoint is mapped to root device (Endpoint 0). The valid
values are explained as follows. The default value is “1”. 0-No endpoint is mapped to root
device; 1-Endpoint 1 is mapped to root device; 2-Endpoint 2 is mapped to root device;
3-Both endpoint 1and 2 are mapped to root device. For example, assumes this parameler
is set to'1 (default value). Gateway or other devices (such as door/window sensor, motion
sensor, etc) that is associated with Light Switch send a command BASIC_SET=0xFF to
Light Switch, the relay in endpoint 1will be turned on; other relay status will not be changed.

9 AirLive SA-105 User Manual
1.5.4 Command Class Interact
Command Class Interact
This Light Switch supports two channel relays. Gateway must use command
MULTI_CHANNEL_CMD_ENCAP to encapsulate the command class switch binary to
control these two relays.
Binary Switch Command Class
Light Switch can be turned on and off by receiving commands
SWITCH_BINARY_SEND or BASIC_SET
RelayOn
Command Class:COMMAND_CLASS_SWITCH_BINARY
Command:SWITCH _BINARY_SEND
Value:0xFF
Relay Off:
Command Class:COMMAND_CLASS_SWITCH_BINARY
Command:SWITCH_BINARY_SEND
Value:0x00
Basic Command Class
The Functions of BASIC_SET= 0x00 And BASIC_SET = 0xFF are same as Binary Switch
Command Class.
1.5.5 Command Classes
The root device of Light Switch supports Command Classes as Below,
*COMMAND_CLASS_ZWAVEPLUS_INFO (V21)
*COMMAND_CLASS_VERSION (V2]
*COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2]
*COMMAND_CLASS_DEVICE_RESET_LOCALLY V1]
*COMMAND_CLASS_POWERLEVEL (V1)
*COMMAND_CLASS_ASSOCIATION (V2]
*COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1]
*COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION (V2]
*COMMAND_CLASS_MULTI_CHANNEL (V4)
*COMMAND_CLASS_SWITCH_BINARY (V1)
*COMMAND_CLASS_CONFIGURATION (V11)
Endpoint 1/2 supports Command Classes as Below (only2CH)
*COMMAND_CLASS_ZWAVEPLUS_INFOV ( 21)
*COMMAND_CLASS_ASSOCIATION (V2]
*COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1)
*COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION (V2)
*COMMAND_CLASS_SWITCH_BINARY (V1)
*COMMANO_CLASS_BASIC (V1)

10 AirLive SA-105 User Manual
1.6 Specifications
Specification
Model
SA-105 Dual Relay Touch
Wall Switch
Z-Wave Standard
Z-wave plus
Z-Wave Frequency
CE：868.40MHz,869.85MHz
Maximum Transmission
Distance
40M (indoor) 100m (open
space)
Supply Voltage
230 VAC
Maximum Output Current
16A (Resistive Load)
Maximum Output Power
2500 W (Resistive Load)
LED Indicator
2 x LED (one per button)
Dimension and Environment
Dimensions
86(L) x 86(W) x 34(H) mm
Operating Temperature
0 ~ 40° C
** Specifications are subject to change and improvement without notice.
OvisLink Corp.,
http://www.airlive.com/
TEL: [phone]
FAX: [phone]