Alcatel-Lucent OmniAccess 5740 User manual

Beta
1
2
Notes on numbered items on banner & legal pages
1u26801 West Agoura Road
Calabasas, CA 91301
[phone]
FAX [phone]
[email protected]
US Customer Support—[phone]
International Customer Support—[phone]
Internet—service.esd.alcatel-lucent.com
Website: www.alcatel-lucent.com
Part No: 060315-00, Rev. A
For final production, import color definitions from
\\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm.
Do not import other template elements such as page layout.
To return to the draft version, import color def’ns from draft-colors.fm.
To switch to the beta version, import color def’ns from beta-colors.fm
OmniAccess 5740
Unified Services Gateway
Getting Started Guide
Release 3.0

CAUTION: THIS EQUIPMENT IS TO BE INSTALLED AND SERVICED ONLY BY QUALIFIED SERVICE
PERSONNEL.
Batteries Caution. There is a danger of explosion if the battery in your chassis is incorrectly replaced.
Replace the battery only with the same or equivalent type of battery recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions. The
manufacturer’s instructions are as follows:
Copyright
The Specifications and Information regarding the products in this manual are subject to change without
notice. All statements, information, and recommendations in this manual are believed to be accurate
but are presented without warranty of any kind, express or implied. Users must take full responsibility
for their application of any products.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED
HEREIN BY THIS REFERENCE.
This equipment has been tested and found to comply within the limits pursuant to the (Centre for
Telecom) rules. These limits are designed to provide protection against harmful interference when the
equipment is operated in a commercial environment.
The following information is for the Users of the OmniAccess 5740 Unified Services Gateway: If it is not
installed in accordance with the installation instructions, it may not function exactly to the said
specifications. Modifying the equipment without Alcatel-Lucent's written authorization may result in the
equipment no longer complying with the said dimensions.
Copyright © 2010, Alcatel-Lucent. All rights reserved.
Not withstanding any other warranty herein, all hardware and software are provided "as is" with all
faults. Alcatel-Lucent disclaim all warranties, expressed or implied, including, without limitation, those
of merchantability, fitness for a particular purpose and non-infringement or arising from a course of
dealing, usage, or trade practice. In no event shall Alcatel-Lucent be liable for any indirect, special,
consequential, or incidental damages, including, without limitation, lost profits or loss or damage to data
arising out of the use or inability to use this manual, even if Alcatel-Lucent have been advised of the
possibility of such damages.
Return the module with the battery to Alcatel-Lucent. The battery will be replaced at Alcatel-
Lucent’s factory.
3
4
5

Table of Contents
Package Contents.....................................................................................................................1
Required Tools and Equipment..........................................................................................2
Connecting AC Input Power......................................................................................................3
Connecting to the OmniAccess 5740 USG Console Port.........................................................5
Starting the OmniAccess 5740 USG.........................................................................................7
Performing Basic Configuration Tasks......................................................................................9
Accessing the OmniAccess 5740 USG Through CLI .........................................................9
Accessing the OmniAccess 5740 USG Through GUI ......................................................15
Cable Connection....................................................................................................................16
Obtaining Technical Support...................................................................................................16

List of Figures
Connecting the Power Cord on OmniAccess 5740 USG 3
Connecting to the OmniAccess 5740 USG System Console 5

List of Tables
Console Properties 6
OmniAccess 5740 USG LED Status 8
Cable Connection 16

OmniAccess 5740 Unified Services Gateway Overview
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
1
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
OmniAccess 5740 Unified Services Gateway Overview
The OmniAccess 5740 Unified Services Gateway (OmniAccess 5740 USG) is
designed to provide most commonly used network services, such as routing,
switching, wide area network (WAN) connectivity, network security with firewall,
and related services using a non-modular platform providing Ethernet switching
and a single WAN interface.
PACKAGE CONTENTS
OmniAccess 5740 USG Hardware
4-slot Chassis that includes
•Services Engine (SE) - 2-port 10/100/1000 Mbps Ethernet
•3 Fans (built-in)
•Power Supply (built-in)
Optional Modules Miscellaneous
•4-port T1E1 Line Card
•8-port 10/100/1000 Mbps Gigabit
Ethernet (GigE) Line Card
•4-port Universal Serial Port (USP) Line
Card (V.35/X.21/RS-232)
•AC Power Cord
•Console Cable
•Rack Mount Screws
•19-inch Rack Mount Ears
•512 MB USB Memory Flash
•Product Documentation CD
ROM

Package Contents
Left running head:
Chapter name (automatic)
2Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
REQUIRED TOOLS AND EQUIPMENT
You need the following items to install the OmniAccess 5740 USG:
•Electrostatic Discharge Wrist Strap (ESD)
•Level (optional)
•Tape Measure (optional)
Note: This equipment is designed to the highest quality standards of materials,
workmanship, and safety. Do not bypass any of the safety features of this equipment
or operate this in an improper environment.
Warning: Only trained and qualified personnel should be allowed to install or replace the
OmniAccess 5740 USG. Refer to the warnings and safety notes that are given in the
“OmniAccess 5740 Unified Services Gateway Hardware Users Guide” provided
with this device.
Refer to the “Rack Mounting the OmniAccess 5740 USG” section in the
“OmniAccess 5740 Unified Services Gateway Hardware Users Guide” to install
the OmniAccess 5740 USG in the rack.

Connecting AC Input Power
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
3
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
CONNECTING AC INPUT POWER
This section provides the procedure for connecting AC-input power to the
OmniAccess 5740 USG.
Note: 1. The OmniAccess 5740 USG installation must comply with all the
applicable codes. All the hardware materials used should be of
compatible material and preclude loosening, deterioration, and electro-
chemical corrosion of hardware and joined material.
2. OmniAccess 5740 USG Power Supply Specification:The OmniAccess
5740 USG requires 100/240V and 6A (RMS) @115V, 3A (RMS) @230V
AC power. A fully loaded OmniAccess 5740 USG consumes
approximately 250W of power.
For more details on power supply specifications, see the “AC Power
Specifications” chapter in the “OmniAccess 5740 Unified Services
Gateway Hardware Users Guide”.
Figure 1: Connecting the Power Cord on OmniAccess 5740 USG
Step 1: Use the shipped power cord to power your system.
Step 2: Verify that the power switch located on the rear panel is in OFF (O)
position.
Step 3: Connect the system end of the connector to the OmniAccess 5740 USG
as shown in the figure above.
Step 4: Identify a power source point that complies with the system specifications,
and connect the power plug of the AC cable to the utility power socket.

Connecting AC Input Power
Left running head:
Chapter name (automatic)
4Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
Step 5: Ensure that the cable is not left in a hazardous position that could impair
movement of personnel or be frayed due to the movement of other equipment in
the vicinity.
Warning: Read the installation instructions before you connect the OmniAccess 5740 USG to its
power source.

Connecting to the OmniAccess 5740 USG Console Port
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
5
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
CONNECTING TO THE OMNIACCESS 5740 USG CONSOLE PORT
The OmniAccess 5740 USG has a RJ-45 console port connector. A RJ-45 - RJ-45
“roll-over” cable along with RJ-45 to DB-9 (female) adapter is provided with the
system to access the console port via a DTE (computer/terminal). For additional
connector details, refer to “Pin Connector Details for OmniAccess 5740 USG”
section in the “OmniAccess 5740 Unified Services Gateway Hardware Users
Guide”.
Figure 2: Connecting to the OmniAccess 5740 USG System Console
Note: Ensure that the OmniAccess 5740 USG is powered off before connecting the console
cable to the system.
OmniAccess
740
USB Modem
Console

Connecting to the OmniAccess 5740 USG Console Port
Left running head:
Chapter name (automatic)
6Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
To connect the OmniAccess 5740 USG to the console, perform the following
steps:
Step 1: Connect the RJ-45 end of the console cable to the front panel console
port on the OmniAccess 5740 USG and the DB-9 end to the serial port (COM) on
your computer/terminal.
Step 2: Start your terminal emulation software.
Example: kermit or hyperterm terminal (if you are using Microsoft Windows
operating system) or minicom terminal (if you are using Unix/Linux operating
system).
Step 3: Set the console session as follows:
Table 1: Console Properties
Step 4: Watch for console message output or press the Enter key to get the
device prompt.
Parameter Value
Baud rate 9600
Parity None
Data Bits 8
Stop Bit 1
Flow control None

Starting the OmniAccess 5740 USG
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
7
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
STARTING THE OMNIACCESS 5740 USG
After installing your OmniAccess 5740 USG and connecting cables, follow the
procedure given below to start the system:
Step 1: Before you power ON the OmniAccess 5740 USG, check the following:
•Ensure that the power supply tray is securely inserted into the chassis.
•Ensure that the utility power cable is connected to a valid power cord in the rear
panel, and power is available from this source.
•Ensure that Services Engine is correctly and securely installed.
•Ensure that a PC or VT100 terminal is connected to the console port, using the
appropriate console cable. (If the system is not connected to a console, see the
“Connecting to the OmniAccess 5740 USG Console Port” section of this
document to connect the system to a console.)
Step 2: Power ON the OmniAccess 5740 USG.
Power on the OmniAccess 5740 USG by turning on the external power switch
located on the rear panel. If power supply is available, you should hear the
rotation of system fans, and the system LEDs showing activity. At this point, the
system begins its bootup sequence.
Step 3: Monitor the system front panel LEDs and console for various bootup
messages.
Once the system begins to startup, monitor the front panel LEDs for various
stages of booting process (refer to the table given below). In addition to the LEDs,
monitor the system console for various bootup text messages (an example of a
bootup message is given below). While a console access is not always required
for system startup, it is a good idea to monitor the console at least the first time
the system is booted and initial configurations completed.

Starting the OmniAccess 5740 USG
Left running head:
Chapter name (automatic)
8Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
LED Information
The following table shows the state in which the main LEDs should be after a
startup:
Table 2: OmniAccess 5740 USG LED Status
The following is an example of a bootup message on OmniAccess 5740 USG:
OmniAccess 5740 USG Bootup Message
Example:
== Press ^C for Boot options ==
== Initiating startup sequence ==
Mounting internal storage medium...OK.
Checking storage medium...Done
###################################################
Alcatel-Lucent Software, Version 3.0.0, Build 82
Copyright (c) 2003-2010 by Alcatel-Lucent Inc.
Built on Tue Jul 6 13:41:35 IST 2010
###################################################
Services Engine [3] Starting internal services
Services Engine [3] Starting daughter processor
Services Engine [3] Installing image package
Services Engine [3] (SE) Installing image package
Services Engine [3] Initialization complete
Services Engine [3] (SE) Initialization complete
Loading Startup Config ...
No Startup Config
Loading Factory Default Config ...
/-------- Percent Complete --------
Username :
Step 4: Configure the system.
LED Status Description
SE LEDs
Active Off Power up status. This is the default
display when the system is first
powered on and before the software is
loaded.
Green SE card is active.
Yellow Indicates transient conditions (e.g.,
booting).

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
9
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
PERFORMING BASIC CONFIGURATION TASKS
Once you boot OmniAccess 5740 USG and connect to the console, you can start
configuring your OmniAccess 5740 USG either through the Command Line
Interface (CLI) or the web-based Graphical User Interface (GUI).
ACCESSING THE OMNIACCESS 5740 USG THROUGH CLI
The CLI is the primary interfaceto access the OmniAccess 5740 USG through the
console. The CLI allows you to configure, monitor, troubleshoot the system, and
enables network connectivity.
Step 1: Once the system bootup is complete for the first time, it always loads with
the factory default configuration.
Note: The factory default configuration is based on the card installed on the OmniAccess
5740 USG.
Step 2: The factory default image on OmniAccess 5740 USG will have the
following configurations preconfigured [with the Serial card (USP -V.35/X.21/RS-
232) installed on the system]:
•HTTPS, SSH access to the system is enabled.
•Default user name and password (superadmin/admin, admin) is enabled with
‘enable’ password ‘admin’.
•SNMP v2 is enabled with read-only community.
•All interfaces will be in administratively ‘UP’ state.
•By default, DHCP client is enabled.
•The DHCP server is enabled on VLAN 1 with pool address from 192.168.1.2 -
254. A host connecting to the VLAN 1 interface receives an address between
192.168.1.2 and 192.168.1.254.
•VLAN 1 will have default IP address 192.168.1.1.
•All switchports will be part of default VLAN 1.
•By default, the serial interface comes up with PPP encapsulation with necessary
configuration to get IP address from the server.
Step 3: You can view the factory default configuration details by executing the
‘show running-configuration’ command.
Example:
The following is an example of show running-config command on the
OmniAccess 5740 USG that displays the factory default configuration:
ALU(config)# show running-config
!Current Configuration:
!
! Statlog Configuration
!
logging on
logging buffered priority 7

Performing Basic Configuration Tasks
Left running head:
Chapter name (automatic)
10 Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
logging buffered size 128
logging console 3
logging system 5
service timestamps log
logging rate-limit 1 10 tag SWE subtag DOS
logging rate-limit 1 10 tag PVSTD subtag PKT
logging rate-limit 1 10 tag SWE subtag SESSION
!
!
!
!VRF Configuration
!
! MULTICAST Configuration
!NOE port reservation
! PVST Global configuration
!
https enable
ssh enable
snmp enable
!
!
! Clock Timezone
!
!
! CWMP Configuration
!
!
! CWMP Configuration (End)
!
!
! CWMP interface configuration
!
!
! CWMP interface configuration (End)
!
!
! SNMP Configurations
!
snmp agent rocommunity aluro
!
aaa services
!
username admin password 5 21232f297a57a5a743894a0e4a801fc3
username recovery password 5
3d58967910ffdbc56565ad089182fbf4
username superadmin password 5
21232f297a57a5a743894a0e4a801fc3
enable password 5 21232f297a57a5a743894a0e4a801fc3
!
!
!
!
aaa authorization disable
!

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
11
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
!
card type E1 1
!
controller E1 1/0
no shutdown
channel-group 0 timeslots 1-31
top
!
controller E1 1/1
top
!
controller E1 1/2
top
!
controller E1 1/3
top
!
!
interface GigabitEthernet3/0
no shutdown
top
!
interface GigabitEthernet3/1
shutdown
top
!
interface Vlan1
ip address 192.168.1.1/24
no shutdown
top
!
interface switchport0/0
no shutdown
top
!
interface switchport0/1
shutdown
top
!
interface switchport0/2
shutdown
top
!
interface switchport0/3
shutdown
top
!
interface switchport0/4
shutdown
top
!
interface switchport0/5
shutdown
top

Performing Basic Configuration Tasks
Left running head:
Chapter name (automatic)
12 Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
!
interface switchport0/6
shutdown
top
!
interface switchport0/7
shutdown
top
!
interface Serial1/0:0
!Note: Effective IP address and MTU will be as negotiated by
PPP
!Note: Any HDLC/Frame-Relay configuration currently does not
apply
encapsulation ppp
ppp ipcp address accept-local
ppp authentication client-username admin
ppp authentication client-password admin
no shutdown
top
!
!
!
! Filter Policy configuration
!
!
!
! Dos attack configuration
!
!
!
! IDS License installed
!
!Snort configuration
firewall
intrusion snort
top
!
!
! Firewall configuration
!
!
! IPSEC License installed
!
! IPSEC Policy configuration
!
! No client object Defined
! No client profile Defined!
!
!QoS Configuration
!
!
!
!DDNS configurations

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
13
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
!
!
!
top
top
!
!Customized-Services
!
!
!
!
!
!
!
top
!
!
!
!
! DHCP Server Configuration
!
service dhcp enable
!
ip dhcp pool p1
network 192.168.1.0 255.255.255.0
range 192.168.1.2 192.168.1.254
!
top
!
!
!
! DHCP CLIENT Configuration
!
!
ip dhcp client default_client
vendor-class-identifier FDC broadband-forum.org
parameter-req-list vendor-specific
top
!
interface GigabitEthernet3/0
dhcp client default_client
top
!
!
!
top
top
!
!
!OAM Configuration

Left running head:
Chapter name (automatic)
14 Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
Alcatel-Lucent
!
oam
top
!
!
!
!NHRP configurations!
top
!
!
! DHCP Relay configuration
!
!
end
Step 4: You can save the factory default configuration to the startup configuration
by using the following command:
Example:
ALU(config)# write mem
Note: In case of reload, the system always boots up with the factory default configuration
unless you explicitly save the modified configuration.
For further configuration of your OmniAccess 5740 USG, refer to the
“OmniAccess 5740 Unified Services Gateway CLI Configuration Guide”
available for download. Refer to the Product Documentation Card for instructions.

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
15
Alcatel-Lucent
Beta Beta
OmniAccess 5740 Unified Services Gateway Getting Started Guide
ACCESSING THE OMNIACCESS 5740 USG THROUGH GUI
Follow the procedure given below to access and configure the OmniAccess 5740
USG through GUI.
Step 1: Open a Web browser from your PC.
Step 2: In the address bar/field, type the IP address of the interface obtained from
the DHCP server and press the Enter key.
Example:
http://<ip address>
http://192.168.1.1
The login page for the Web GUI is displayed in the browser window.
Note: Execute “show ip interface brief” command to view the IP address obtained from the
server.
Step 3: Enter the default user name and password (superadmin/admin, admin),
and press the Enter key.
Step 4: This will launch a web interface to configure your OmniAccess 5740 USG.
For further configuration of your OmniAccess 5740 USG, refer to the
“OmniAccess 5740 Unified Services Gateway Web GUI Users Guide”.