Alcatel T70 User manual

OR
OR
OR
OR
INTRODUCTION
Your Caller ID phone stores and displays specific information, provided by your
local telephone company, to subscribers of Caller ID or similar caller
identification services.
Your Caller ID phone enables you to:
·Identify callers before you answer the phone.
·View the time and date of each incoming call.
·Record up to 68 Caller ID messages sequentially.
·FSK/DTMF Caller ID auto detect.
·Alphanumerical backlight display.
·Incoming call log records up to 68 calls.
·Outgoing call log records up to 15 last dialed numbers.
·8 one-touch memories.
·10 two-touch memories.
·On hook pre-dialing.
·Prefix Code.
·Redial.
·Pulse or Tone dialing mode.
·Mute function.
·Speakerphone.
MAIN FEATURES
To get the most from your new phone, you are suggested to take a few
minutes right now to read through this user guide.
SHORT GLOSSARY OF TERMINOLOGY USED IN THIS
MANUAL
Hook switch. The part of the phone that pops up to activate the phone line
when the handset is lifted from the base.
Off-hook. A term used to describe the phone in its active mode when the
handset is off of the base cradle or when the SPEAKER button is pressed.
On-hook. A term used to describe the phone in an inactive mode.
Make sure your package includes the items:
PARTS CHECKLIST
NOTE: If you find any of the parts missing, please contact your local
shop where you buy this product right away.
Base Handset Coil cord
Modular telephone line jack
Wall plate
To use this phone, you need a RJ11C type modular telephone jack, which
might look like the one pictured here, installed in your home.
If you don't have a jack, call your local phone company to find out how to
get one installed.
TELEPHONE JACK REQUIREMENTS
Line cord
INSTALLING THE PHONE
Your phone should be placed on a level surface, such as a desk or table top,
or you can mount it on a wall.
1. Connecting the handset.
2. Connecting the telephone
line.
WALL MOUNTING: The knob is designed to
keep this unit in place when the telephone is
vertical on the wall.
IMPORTANT: If you are not going to use the telephone for more
than 30 days, remove the batteries because they may leak and
damage the unit.
INSTALLATION
CAUTION: Disconnect the phone cord from the wall outlet
before installing or replacing the batteries.
·Never install telephone wiring during lightning storm.
·Never touch un-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
·Use caution when installing or modifying telephone lines.
·Never install telephone jack in wet location unless the jack is specifically
designed for wet locations.
·Temporarily disconnect any equipment connected to the phone, such as
faxes, other phones or modems.
INSTALLING AND REPLACING THE BATTERIES
Your Caller ID phone uses 3 AA-Size alkaline batteries for receiving and
storing Caller ID records and for storing the numbers you use frequently.
BATTERY
1. If the telephone line cord is connected, disconnect it from the base unit.
2. Carefully turn over the phone, use a pen or paper clip to loosen the
battery cover. Open the battery compartment by pushing on the battery cover
and sliding it away from the unit.
3. Insert 3 AA-size alkaline batteries (not included) as shown on the diagram
in the battery compartment.
4. Snap the battery compartment door
back into place.
5. If the line cord was previously
connected, reattach it to the unit
and check your memory locations.
Wall mounting knob
location Rotate 180°
WALL MOUNTING
1.Rotate the wall mounting knob as shown in the following layout:
OPTIONS MENU
Outgoing call
New Caller,
Repeat Caller,
Mail information
Speakerphone
Day Minutes Incoming Call
Phone number display
Week display
Mute Mic
Hour
Month Call-log Number
User s Guide'
2. Install the base unit to the wall and then plug one end of line cord into the
junction box and the other end into modular telephone line jack marked
" ".
3. Fix the telephone in the wall as the following layout.
SETTING THE PHONE
There are 4 options to set:
NOTE: Proceed immediately to change any of the following factory
preset as required.
Date and Time Setting.
Pcode is a prefix code that user may add to the front of the
number before dialing.
Select the dialing mode. This is dependent of the telephone
company you are connected to.
Timing setting. This timing is to allow user to momentary
access telephone services such as call waiting when FLASH
button is pressed.
SIZ E A A
SIZ E A A
SIZ E A A
SETTING DATE/TIME
Press and Hold
2 Seconds
Enter Year, Month,
Day and Time
SETTING PCODE
Press and Hold
2 Seconds
Ringer Vol Switch
Speaker button
Out button
Redial/pause button
Flash button
Display
Up button
Down button
Delete button
Speaker Vol Switch
Microphone
Programme
button
Mute button
Mem button
Menu button
Memory button
Message/In use
indicator
Dial button
SETTING TONE/PULSE
Tone Pulse
Select Tone or Pulse
Press and Hold
2 Seconds
SETTING FLASH
100/300/600
Select Timing
Press and Hold
2 Seconds
OR
User’s guide
ALCATEL T70
User’s guide
ALCATEL T70

MAKING A PHONE CALL
Dial number
Caller ID (CID) is a service available from your local telephone company.
For Caller ID to work on this system, you must subscribe to Caller ID service.
This unit can receive caller ID without any setting. Your Caller ID information
may include the phone number, date and time.
CALLER ID FEATURES
REVIEWING INCOMING CALLS
CONTRAST/MUTE
In off-hook state, user can press the MUTE button to access mute function.
When CONTRAST/MUTE is on, the CONTRAST/MUTE indicator will show on
the screen.
Press the MUTE button to exit mute function and resume normal
conversation.
In on-hook state, user can press the MUTE button to selection the LCD
Contrast ( 1~5 chioce,default 3).
P=>T DIAL MODE
In PULSE dialing mode, press[*] button to access TONE service.
Last number redial
REDIAL
CONTRAST LEVEL ADJUSTMENT
In on-hook state, press the MUTE button to adjust the display contrast level.
TROUBLESHOOTING TIPS
No Dial Tone
· Check all cabling to make sure that all connections are secure and not
damaged.
· Check hook switch: Does it fully extend when handset is lifted from cradle?
No Display
· Replace the batteries.
· Check for proper battery installation.
Model ALCATEL T70-EX
A/W No.: 10000669 Rev.1 (EN)
14-08
Printed in China
DIAL BACK A CALLER ID NUMBER
Select the caller number
The number shown will be dialed
Press " 0 " key 2 seconds
PCODE will be added to
the front of number shown
Select the caller number
The number shown will be dialed
REVIEWING OUTGOING NUMBERS
DIAL BACK AN OUTGOING NUMBER
The number shown will be dialed
MEMORY OPERATIONS
DELETING A CALLER ID NUMBER
Select the number
Dial number
CASE 1
The number shown will be dialed
CASE 2
CASE 1
The number shown will be dialed
CASE 2
Reviewing Incoming Call Log
CASE 1
CASE 2
No Information is Shown After the Phone Rings
· Have you subscribed to Caller ID service from your local telephone
company?
· Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
· Make sure T/P DIAL MODE is set to TONE DIAL.
Phone Won't Dial Out with Pulse Service
· Make sure T/P DIAL MODE is set to PULSE DIAL.
Phone Does Not Ring
· You may have too many extension phones on your line. Try to unplug
some extension phones.
· Check for dial tone. See troubleshooting tips for no dial tone.
Incoming and Outgoing Voice Volume Low
· Are other phones off hook at same time? If so, this is normal condition as
volume drops when additional phones are used at once.
· Check the handset receiver or speaker volume.
GENERAL PRODUCT CARE
To keep your phone working and looking good, follow these guidelines:
· Avoid putting it near heating appliances and devices that generate
electrical noise (for example. Motors or fluorescent lamps).
· DO NOT expose to direct sunlight or moisture.
· Avoid dropping and other rough treatment to the unit.
· Clean with a soft cloth.
The store where you bought your telephone can also provide you with
information and after-sales support.
Used equipment must be disposed of in compliance with
current environment protection regulations.
You should return it to your reseller or dispose of it in an
approved recycling center.
OR
OR
OR
OR OR
OR
OR OR
OR
OR
OR OR
OR OR
STORING A TELEPHONE NUMBER
Dial number Memory location
M1~M8
OR
STORING INCOMING CALL NUMBER
Select the number Memory location
M1~M8
OR
STORING OUTGOING NUMBERS INTO MEMORY
Select the number Memory location
M1~M8
OR
CASE 1
DIALING A MEMORY LOCATION
Select a Memory Location
CASE 2
Memory Location
+
M1~M8
OR OR
OR
+
M1~M8
OR
OR
DELETING A MEMORY LOCATION
Select a Memory
Location
Press and Hold
2 Seconds
+
M1~M8
OR
OR OR
Select the caller number Add number to the front
The number shown will be dialed
CASE 3
PHONE OPERATION
RECEIVING A PHONE CALL
Answer Call End Call
End Call
Ringing
CASE 1
Answer Call
Ringing
CASE 2
End CallAnswer Call
Ringing
CASE 3
End Call
Answer Call
Ringing
CASE 4
· Never use a strong cleaning agent or abrasive powder because this will
damage the finish.
· Retain the original packaging in case you need to ship it at a later date.
www.alcatel-home.com