Alemlube S Series User manual

Description
With covers manufactured from high quality impact resistant and UV stabilised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the new S Series SOI700 oil hose reel from Alemlube will provide you with a reliable &
cost effective means of storing and retrieving hose assemblies in your workshop. The reel can be floor, ceiling or wall mounted & the
detachable mounting bracket facilitates ease of reel mounting & storage.
Specifications
Operation
1 Check your S Series reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2 Latching mode switch, when your S Series reel is in free run state, pull out
the hose and allow it to retract after hearing the first, second or third click.
3 To unlatch the reel, slowly pull out the hose until the clicking noise stops, and
then let the hose retract unitl the hose stop rests against the hose guide.
4 NOTE: To avoid damage to your S Series reel, always hold onto the hose while it is rewinding. Periodically check the hose
condition for wear or damage and check the swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1 Make sure incoming line pressure does not exceed the rated operating pressure for your model hose reel.
2 Use proper eye protection when assembling and using the hose reel.
3 Use soap and water when checking for leaks.
4 Keep children away from the work area.
Installation Of Reel
1 For overhead ceiling mounting: install reel at most,
3m above the floor.
2 You will need to purchase appropriate hardware for
the mounting of your new reel.
3 The reel base has four 7mm (11/16") drilled holes for
mounting on a suitable flat surface. Figure 2 is a
template showing the correct location of the 4 mounting
holes in the base.
4 Using the three holes in the base, mount the reel in the
desired location. Be sure to use appropriate hardware
and to tighten the reel securely to the mounting location.
5 Apply Teflon tape or pipe sealant to the outlet fitting on the
hose & then attach to desired tool or nozzle. Check
connection for any leakage & check the reel for correct
operation. See operation section. If hose stop adjustment is
required, pull hose from reel and allow the reel to latch at the
desired length. Loosen hose stop bolts and slide hose stop to
a position close to the hose guide. Tighten hose stop bolts
and unlatch the reel.
Use Oil
Hose Length S.A.E 100R1 rubber, 10m x 12mm ID hose
Materials Plastic covers, steel spring & Buna “N” seals
Pressure 2000psi (138 bar)
Weight/Dimensions 15.6kg / 490mm (L) x 448mm (H) x 228mm (W)
Inlet/Outlet 1/2"BSPT(m)
Working Temp -30°C ~100°C
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
S Series Oil Hose Reel SOI700
OWNER’S TECHNICAL MANUAL
NSW/ACT
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]

2
Parts and Drawing Breakdown for
S Series SOI700 Oil Hose Reel
Ordering Spare Parts
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NSW/ACT
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
ITEM No. PART No. DESCRIPTION QTY
1 SOI700-1 Screw ST4.8x13 F 8
2 SOI700-2 Clip for Ratchet 1
3 SOI700-3 Screw ST4.2x16 F 8
4 SOI700-4 Small Cover 1
5 SOI700-5 Cover for Axle 1
6 SOI700-6 Screw ST2.9x13 F 2
7 SOI700-7 Ratchet 1
8 SOI700-8 Ratchet Ring 2
9 SOI700-9 Ratchet Spring 1
10 SOI700-10 Screw ST3.5x13 C 3
11 SOI700-11 Hose Assembly 1
12 SOI700-12 Bracket 1
13 SOI700-13 Stator 1
14 SOI700-14 Axle 1
15 SOI700-15 Stator 2
16 SOI700-16 Screw ST4.87x75 C 3
17 SOI700-17 Main Spring 1
18 SOI700-18 Red Cover 2
19 SOI700-19 Nut M4 10
20 SOI700-20 Big Cover 1
ITEM No. PART No. DESCRIPTION QTY
21 SOI700-21 Swivel Assembly 1
22 SOI700-22 Cover for Spool 1
23 SOI700-23 Screw M5x12 2
24 SOI700-24 Inlet Hose Assembly 1
25 SOI700-25 Screw M4x1 10
26 SOI700-26 Spring Clamp 1
27-1 SOI700-27-1 Screw M6x40 2
27-2 SOI700-27-2 Washer 8 2
27-3 SOI700-27-3 Hose Stopper 1
27-4 SOI700-27-4 Nut 2
28 SOI700-28 Tube Fitting 1
29 SOI700-29 Guide Protector 1
30 SOI700-30 Washer 3 3
31 SOI700-31 Drum 2
32 SOI700-32 Main Axle 1
33 SOI700-33 Washer 4 1
34 SOI700-34 Screw ST2.9x9.5C 1