Alemlube 660AN User manual

De cription
Model 660AN is a trigger action 450gm grease gun capable of delivering up to 1.1cc of grease per stroke at a maximum
operating pressure of up to 8,500psi. It comes standard with a 30cm flexible extension & a 4 jaw coupler for those
difficult to get at lubrication points. The 660AN has a 600gm capacity when using bulk grease & features a slip-type
pressure/volume adjustment which changes the gun from high pressure to high volume.
Specification
Uses 450gm Grease Cartridges, Suction loading, Bulk loader pump from bulk grease drum
Grease Pressure Maximum operating pressure of up to 8,500psi
Delivery 0.64cc per stroke (high pressure setting) / 1.1cc per stroke (high volume setting)
Capacity 600gm capacity when using bulk grease
Air pocket in grea e:
If the gun is pumped but no grease appears from the coupler: Depress the air bleeder valve on the head and pump a
few strokes. Unscrew the barrel assembly from the gun head with two or three turns and then push on the plunger rod.
With the follower cup engaged, the follower cup will move further down into the barrel venting any trapped air out
through the thread connections between the barrel and head. Unscrew the flex extension as well.
Operating in truction
There are two ways to fill the gun with grease:
A) 450gm Grease Cartridge:
Unscrew the grease barrel from the gun and insert the 450gm grease
cartridge by holding the barrel assembly & pulling therod back. Remove
cap from the grease cartridge, insert the cartridge into the barrel & then
rescrew the barrel assembly back onto the gun so that the cartridge sits
well against the follower cup. nce in position, press the clamp down &
push the rod firmly back into the barrel.
Important To Note:
When using the gun with a cartridge, the follower cup must be folded
back. The gun is supplied standard with the follower cup in this position.
B) Bulk Grease Loading:
Unscrew the grease barrel from the gun head & insert the barrel into
the bulk grease. Suck the grease up into the barrel by pulling the rod all
the way back. When barrel is full with grease, rescrew the barrel
assembly back onto the gun head so that the follower sits well against
the grease. Press the clamp down & push the rod firmly back into the
barrel.
Important To Note:
When using the gun with bulk grease, the follower cup must be folded
forward. To do this, take the follower cup and rod assembly out of the
barrel, fold the follower cup forward and reassemble the barrel
assembly.
Maintenance
Cleaning: always keep the follower cup free of impurities. Your grease
should be clear of any foreign particles, dirt etc and the gun should be
checked and cleaned regularly.
Trouble Shooting
Visit our website at www.alemlube.com.au Email - [e-mail]
660AN Trigger Action Grease Gun 660AN
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
OWNER’S TECHNICAL MANUAL
660AN_660A 18/04/11 10:27 AM Page 1

13
Part And Drawing Breakdown For The 660AN
Ordering Spare Part
Parts List – Part No. 660AN
2
Item Number Part Number Product De cription Qty
1 660AN-1 Barrel 1
2660AN-2 T-grip handle 1
3660AN-3 Hex nut 1
4660AN-4 Arrester clamp 1
5660AN-5 Barrel cover 1
6660AN-6 Draw rod 1
7660AN-7 Spring 1
8660AN-8 Distance holder 1
9660AN-9 Forming disc 1
10 660AN-10 Follower cup 1
11 660AN-11 Washer 1
12 660AN-12 Ring 1
13 660AN-13 Grease gun head assemly 1
Visit our website at www.alemlube.com.au Email - [e-mail]
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
660AN_660A 18/04/11 10:27 AM Page 2