Schlage FE595 User manual

Install Lock
Remove Template From Booklet
12
H
A
K
E
D
J
L
M
B
C
F
G
A. Outside Knob/Lever
B. Pin Wrench
C. Key
D. Keypad Assembly
E. Latch
F. Latch/Strike Screws
G. Strike
H. Inside Mounting Plate
J. Mounting Plate Screw
K. Inside Thumbturn Assembly
L. Mounting Screws
M.Inside Knob/Lever
N. 9V Battery
P. Drive-in Faceplate
Q. Square-corner Faceplate
Tools for Installation
OR
2
A. Key
1. Turnson the backlight.
2. Indicates lockstatus (programming
mode, low battery,etc.)and success
or failure ofan operation.
3.Confi
rms a menu entryduring
programming (see page 8).
4.Used to exit programming or to clear
an incorrect entry.
B. Keypad
1.Used to unlockthe lockbyenteringa
validfour-digituser code.
2. Usedto program the lock.
(See page 8.)
C.Key Override (See page 11.)
Usedto unlockthe lock in the following
situations:
1.L
ockhas failedelectronically.
2. Batteryis dead.
3.U
ser code is not known.
D.Outside Knob/Lever
To minimize damage from vandalism,
the outside knob/leverrotates but does
not retract latch evenwhen lockis
locked.
E.Inside Knob/Lever
The inside knob/lever is always
unlockedforimmediate exit.
FE575 Features
A. Key
B. Keypad
C. KeyOverride
D.OutsideKnob/Lever
E. Inside Knob/Lever
ab
2³⁄₈”(60 mm) To DoorEdge
CUT HERE
2³⁄₄”(70mm) To DoorEdge
1⁵⁄₈"
For 1³⁄₈"
ThickDoor
For 1³⁄₄"
ThickDoor
⁷⁄₈”
(22 mm)
Hole
T
emplate for FE575, FE595,BE365
For Use With
OR
2¹⁄₈”
(54mm)
Hole
OR
Match to Door Edge Door Edge
2³⁄₈” or 2³⁄₄”
R
o
t
a
t
e
T
e
m
p
l
a
t
e
t
o
M
a
t
c
h
D
o
o
r
Installation Instructions
FE595
P515-548
N
Q
P
Check Door Holes
Note: If door holes do not match template, visit
www.schlage.com for door drilling instructions.
5¹⁄₂”
Minimum
T
emplate for FE575, FE595, BE365
2³⁄₈”(60 mm) To Door Edge
R
o
t
a
t
e
T
e
m
p
l
a
t
e
t
o
M
a
t
c
h
D
o
o
r
2³⁄₄” (7 0 mm) To DoorEdge
OR
2¹⁄₈”
(54 mm)
Hole
2³⁄₈” or 2³⁄₄”
Door Edge
For 1³⁄₈"
Thick Door
For 1³⁄₄"
Thick Door
1⁵⁄₈"
⁷⁄₈”
(22 mm)
Hole
For Use With
OR
Match to Door Edge
CUT HERE
Keep the programming
booklet with you while
installing lock. Without
the user codes, you can
get locked out.
STOP

Install Keypad Assembly
IMPORTANT: Cable must slide under latch.
5
Bevel
Jamb
Jamb
3
4
Use
Move to Step 5
For For
Use Use
For
Wood Block
(Not included)
Actual Size
Install Latch
IMPORTANT: Latch bevel must face door jamb.
OR
Bevel
Choose Deadbolt Faceplate

Install Inside Mounting Plate
IMPORTANT: Pull excess wire through mounting plate.
Install Battery and Connect Cables
IMPORTANT: Cable must be routed and tucked as shown.
67
a
b
Tu c k C a bl e
d
a
b
c

©2006 Schlage Lock Company
Printed in U.S.A.
P515-548 Rev. 6/06 CD
b
Install Inside Thumbturn Assembly
Note: Lock should be straight on door before tightening
screws.
8
If Needed, Install Knobs/Levers
If Needed, Change Levers
9
10
Install Strike onto Door Jamb
10
Correct
Actual Size
Match
Flat Sides
d
Actual Size
Tip Pointing Down
a
a
b
c
Incorrect
c