Allegion Falcon S Series Instruction sheet

1 2 3 4
5 6 7 8
MARK DOOR BORE 3 HOLES INSTALL LATCH AND STRIKE REMOVE INSIDE TRIM
ADJUST FOR
DOOR
THICKNESS ENGAGE LOCK WITH LATCH SECURE LOCK TO DOOR INSTALL KNOB
Recommended template instructions
must be followed to assure proper
functioning. (See attached template).
Mark centers for latch hole, side hole
and rose insert points on both sides of
door.
A. Bore side hole from both
sides of door.
B. Bore latch hole.
Use strike locating tool
or other pointed object
to locate position for
hole in jamb.
C. Bore jamb.
NOTE: A minimum ³⁄₄”
deep hole must be
bored in frame behind
opening in strike for
proper function of latch bolt.
Outline latch face and strike as illustrated
and chisel out to proper depth.
Install latch.
Be sure beveled
side of latch
bolt is facing
the door frame.
If dust box is
to be used,
clear area
with wood
chisel.
Depress knob catch to remove knob.
Remove rose by unscrewing collar
If Cylinder knob, see reverse side.
Hold lock against edge of door. Adjust
outer rose collar so door center mark on
lock housing is in center of door.
Wrench can be used to adjust lock for door
thickness by holding tip of wrench against
rose insert and turning rose collar until
desired arrow on wrench lines up with arrow
on lock case.
ALTERNATE
METHOD
Centerline of
door and lock
Door Edge
12172 WRENCH
Both latch prongs engage housing.
Housing Retractor
engages
latch tail.
Replace inside rose and collar
and using spanner wrench
turn collar clockwise and
tighten firmly.
Place knob on spindle, slide to knob
catch, depress knob catch and push
knob until catch engages slot in knob.
If cylinder knob, see reverse side.
TEMPLATE FOR S AND X SERIES
RECOMMENDED TEMPLATE INSTRUCTIONS MUST BE FOLLOWED TO ASSURE PROPER FUNCTIONING.
DISTANCE
FROM EDGE
OF DOOR
(BACKSET)
¹⁄₈” DIA (3.2 mm) 2 HOLES ¹⁄₈” DEEP BOTH SIDES OF DOOR
3³⁄₄"
(95 mm)
2³⁄₈"
(60 mm)
FOLD ALONG EDGE OF DOOR
SECOND BORE LATCH HOLE PARALLEL TO SIDES. ⁷⁄₈” (22mm) FOR 2³⁄₈” BACKSET 1” (25mm) FOR 2³⁄₄” OR LONGER BACKSET
CENTER FOR 1³⁄₈”
(35 mm)
DOORS
CENTER FOR 1³⁄₄”
(44 mm)
DOORS
Remove template from instructions.
FIRST BORE 2¹⁄₈” (54 mm) HOLE AT CORRECT BACKSET AND ¹⁄₈” (3.2 mm)
CLEARANCE HOLES FOR ROSE INSERT POINTS
TEMPLATE FOR S AND X SERIES
RECOMMENDED TEMPLATEINSTRUCTIONS MUST BE FOLLOWED TO ASSURE PROPER FUNCTIONING.
DISTANCE
FROM EDGE
OF DOOR
(BACKSET)
¹⁄₈” DIA (3.2mm)
2 HOLES ¹⁄₈” DEEP
BOTH SIDES OF DOOR
3³⁄₄"
(95 mm)
2³⁄₈"
(60 mm)
FIRST
BORE 2¹⁄₈” (54 mm) HOLE ATCORRECT BACKSET
AND ¹⁄₈” (3.2
mm
)
CLEARANCE HOLES FOR ROSE INSERT POINTS
FOLDALONG EDGE OF DOOR
SECOND
BORE LATCHHOLE
PARALLELTO SIDES.
⁷⁄₈” (22mm) FOR 2³⁄₈” BACKSET
1” (25mm) FOR 2³⁄₄”
OR LONGER BACKSET
CENTER
FOR 1³⁄₈”
(35mm)
DOORS
CENTER
FOR 1³⁄₄”
(44mm)
DOORS
Remove template from instructions.
B
A
C

INSTRUCTIONS FOR
REMOVAL OF AND
REASSEMBLY OF
CYLINDER KNOB
TO REMOVE CYLINDER KNOB
HOW TO
INSTALL
S SERIES
AND
X SERIES
FALCON
LOCKS
HOW TO
INSTALL
S SERIES
AND
X SERIES
FALCON
LOCKS
Cylinder knob should be installed as shown.
(key notches up)
If necessary to change hand of lock
so that cylinder will be right side up,
use the following instructions:
Assembly not installed in door:
Rotate key ¹⁄₄ turn clockwise,
depress knob catch and pull off
knob. Rotate housing 180° and
reinstall cylinder knob.
Assembly installed in door: Rotate
key ¹⁄₄ turn clockwise, depress
knob catch and pull off knob.
Rotate knob 180° and reinstall
cylinder knob.
With key in cylinder, align hole in knob
cap with knob catch and slip knob over
spindle up to knob catch.
KNOB CATCH
KNOB CATCH
With knob against knob catch, and
cylinder tailpiece engaged with key
spindle, hold knob, rotate key ¹⁄₄ turn
clockwise. Depress knob catch and
push knob until catch engages slot
in knob.
TO INSTALL CYLINDER KNOB
STEP ONE STEP TWO
TEMPLATE FOR S AND X SERIES
RECOMMENDED TEMPLATE INSTRUCTIONS MUST BE FOLLOWED TO ASSURE PROPER FUNCTIONING.
DISTANCE
FROM EDGE
OF DOOR
(BACKSET)
5"
(127 mm)
2 ³⁄₄"
(70 mm)
FOLD ALONG EDGE OF DOOR
SECOND BORE LATCH HOLE IN CENTER OF DOOR PARALLEL TO SIDES. 1” (25 mm) FOR 2³⁄₄” OR LONGER BACKSET
CENTER FOR 1³⁄₈”
(35 mm)
DOORS
CENTER FOR 1³⁄₄”
(44 mm)
DOORS
FIRST BORE 2¹⁄₈” (54 mm) HOLE AT CORRECT BACKSET AND ¹⁄₈” (3.2 mm)
CLEARANCE HOLES FOR ROSE INSERT POINTS
LITHO IN U.S.A.
¹⁄₈” DIA (3.2 mm)
2 HOLES ¹⁄₈” DEEP
BOTH SIDES OF DOOR
© Allegion 2014
Printed in U.S.A.
002290-000-70 Rev. 10/14-d

3.06
4.000
Additional Notes: Revision History Revision Description:
D > Revised artwork
1. None A B C D E F
4526 0790 6683
Material
White Paper
Edited By Approved By EC Number Release Date
J. Ellis M. Roberts xxxxx 10/14
Notes
1. printed two sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. ok to fold into uneven sections
6. barcode shows after folding
Title
Sheet Instruction, S & X
Creation Date
10-22-14
Number
002290-000-70
Revision
D
Created By
J. Ellis Activity
3899 Hancock Expwy
Security, CO 80911 © Allegion 2014Software: InDesign CS6
8.000
14.88
BEGINNING SHEET
FOLDED SHEET
FRONT
FRONT