Allegion Falcon F Series User manual

*030690-000-70*
030690-000-70
© Allegion 2014
Printed in U.S.A.
030690-000-70 Rev. 10/14-d
Customer Service
1-877-671-7011 www.allegion.com/us
Installation Instructions
F-Series
Keyed Locks
ROSE
INSIDE
LEVER
UL
LATCH
SHIELD *
OUTSIDE
LEVER
ASSY
#8 COMBO
SCREWS
#10-32
MACHINE
SCREWS
INSIDE
SPINDLE
ASSY
LATCH ASSY
NOTCHES
* NOTE: UL LATCH SHIELD IS ONLY
REQUIRED WITH UL LATCHES
1. MARK DOOR 2. DOOR PREPARATION 3. INSTALL STRIKE
4. INSTALL LATCH SHIELD 6. INSTALL OUTER TRIM 7. INSTALL INNER SPINDLE
ASSEMBLY
A. Mark height line on edge of door
approximately 38” from floor.
B. Using the proper backset, mark 2¹⁄₈” hole on
both sides of the door.
C. On the outside of door, mark notches.
D. Mark the center of the door edge for the latch.
A. Bore 2¹⁄₈”
hole thru from
both sides of
door to prevent
splintering door
finish.
B. File notches on
outside of door being careful not
to exceed the 2¹⁵⁄₃₂" dimension.
C. Bore 1” hole for latch on door
edge.
D. Using the latch faceplate as a
guide, trace outline and mortise
door edge so latch is flush with
door.
NOTE: Hollow metal doors must be properly
reinforced for lock support. If support was not
furnished contact door manufacturer.
1”
HOLE
2¹⁄₈”
HOLE
A. Use strike locating tool or pointed
object to locate position for hole in frame.
B. Bore 1” x ³⁄₄” deep hole. Use strike as a
template and mortise to the proper depth.
C. If dust box is to
be used, clear area
with wood chisel.
FOR UL LATCH OPTION ONLY
A. Insert latch shield
(closed end first)
from the outside of the door.
CAUTION:
Failure to
use the latch
shield with a
UL latch will
invalidate the
UL listing of
this product.
5. INSTALL LATCH
A. Insert latch into door, making certain that
bevel faces direction of closing door.
B. Secure with two #8 combo screws provided.
A. Align spindle with latch unit
and insert outer trim into door. A. Align spindle assembly with square
shaft and slide into place.
NOTE: Locking button must be positioned
towards the edge of the door.
B. Secure with two screws provided.
locking button

2
TEMPLATE FALCON F-SERIES LOCKS
IMPORTANT:
NOTCHES REQUIRED
IN EXTERIOR SIDE OF
DOOR FOR LOCK TO
MOUNT & FUNCTION
PROPERLY.
FIRST:
BORE 2¹⁄₈” (54mm) HOLE AT CORRECT BACKSET SECOND:
BORE LATCH HOLE
PARALLEL TO
SIDES 1” (25mm)
DISTANCE
FROM EDGE
OF DOOR
(BACKSET)
FOLD ALONG EDGE OF DOOR
HEIGHT
LINE
⁵⁄₃₂” (4mm)
x
³⁄₃₂” (2mm)
DEEP
2³⁄₄”
(70mm)
2³⁄₄”
(60mm)
Center
for 1³⁄₈”
(35mm)
DOORS
Center
for 1³⁄₄”
(44mm)
DOORS
RECOMMENDED TEMPLATE INSTRUCTIONS MUST
BE FOLLOWED TO ASSURE PROPER FUNCTION
8. INSTALL INSIDE TRIM
A. Snap rose over mounting plate.
B. Place lever on spindle and slide to
locking button.
C. Push lever in until button engages
hole in lever.
D. Check function before closing door.
9. REMOVING STANDARD
CYLINDERS & LEVERS
A. Insert key and turn 90°
counter-clockwise to unlock lockset.
B. Depress locking button and pull off lever
and cylinder.
MOUNTING
PLATE
ROSE
LEVER
LOCKING
BUTTON
LOCKING
BUTTON
10. INSTALLING STANDARD
CYLINDERS & LEVERS
A. Insert cylinder into lever.
B. Insert key into cylinder.
C. With notches of key facing up, align hole in
lever with locking button on spindle assy and
slide lever to locking button.
D. Push lever until lever engages button.
E. Check function before closing door.
LOCKING
BUTTON
HOLE
11. REMOVING IC CORE
A. Unlock lockset.
B. Turn control key 15 degrees
clockwise until key stops.
C. Pull key to remove IC core.
LOCKING
BUTTON
12. REMOVING IC LEVERS
A. With IC core removed, depress locking button
and pull lever to remove.
13. INSTALL IC LEVERS
A. Slide tailpiece assembly into spindle,
engaging the single leg with the drive cam
in the spindle.
B. Insert spindle cap into the lever, notched
end first.
C. Push lever in until locking button
engages hole in lever.
D. With control key in core rotate key 15°
clockwise and insert fully into lever. Turn the
key counter-clockwise and remove key.
E. Check function before
closing door.
TAILPIECE
ASSEMBLY
SPINDLE
CAP
14. TAILPIECE INSTALLATION
A. Insert spring and pin into cylinder.
B. Place tailpiece into cap.
C. Thread cap onto the cylinder.
NOTE: The cap must be properly adjusted. If
too loose, excessive plug end play will prevent
the key from being withdrawn. If too tight, the
plug will drag and be difficult to rotate with the
key.
CYLINDER
SPRING
PIN
TAILPIECE
CAP
2¹⁵⁄₃₂”
(63mm)
MAX
REMOVE TEMPLATE FROM INSTRUCTIONS

4.250
3.670
Additional Notes: Revision History Revision Description:
D > Revised artwork
1. None A B C D E F
4600-304 0790 6683
Material
White Paper
Edited By Approved By EC Number Release Date
J. Ellis M. Roberts xxxxx 10/14
Notes
1. printed two sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. drawings not to scale
6. Barcode shows after folding
Title
F-Series Keyed Locks
Creation Date
10-22-14
Number
030690-000-70
Revision
D
Created By
J. Ellis Activity
3899 Hancock Expwy
Security, CO 80911 © Allegion 2014Software: InDesign CS6
8.500
11.000
BEGINNING SHEET FOLDED SHEET
FRONT
FRONT