Allen-Bradley 1492-CM1771-LD008F User manual

Fused Field Wire Conversion Module for A-B 1771-OBD to two 1756-OC8
(Cat 1492-CM1771-LD008F)
Local language (French, Italian, German & Spanish) versions of this document can be downloaded by going to www.ab.com. In
the left margin click on Publications Library and Literature Library. In the Search Area (right margin), Search by Catalog
Number and in the Search box type in the catalog number of the conversion system component.
I. Module Description
The 1492-CM1771-LD008F, fused conversion module provides field wire signal conversion from an A-B 1771-OBD,
10 to 60Vdc, 16 point output module to two (2) 1756-OC8, 30 to 60Vdc, 8 point output modules. The conversion
module provides the mating connector to the 1771-OBD module swing-arm/terminal block with the attached field
wires. It routes those signals via its 37-pin connector and a single 1492-CONCABS1 pre-wired cable to compat-
ible terminals on the two (2) 1756-OC8 modules. To maintain the functionality of the 1771-OBD module the
conversion module provides 1 mechanical fuse; 1 for each DC+ (refer to the Wiring Diagram on page 2 for details).
NOTICE: The two 1756-OC8 modules must be located directly adjacent to each other in the 1756 chassis, due to
the orientation of the 1756 terminals on the 1492-CONCABS1 pre-wired cable.
II. Module Installation
The 1492-CM1771-LD008F conversion module must be installed in a 1492 conversion base-plate and cover-plate
assembly. The installation of the module into the assembly is explained in the Installation Manual that ships with the
conversion assembly. For a list of compatible assemblies refer to Appendix A
III. Conversion Module Compatibility Matrix
 This is cable length in meters. Available lengths are limited to 005 (0.5m) and 010 (1.0m)
PN-40381
DIR 10000045377 (Version 00)
Printed in U.S.A.
Conversion Module Compatible 1771
Output Module
Compatible 1756
Output Module
Required 1492 Cable
1492-CM1771-
LD008F
1771-OBD Two
1756-OC8
1492-CONCABS1
De-energize and lockout any and all power to all I/O field devices connected to the A-B 1771 I/O
chassis, and the power to the 1771 I/O chassis itself. Ensure all power is de-energized and locked out
to any device in the control cabinet where the conversion is to be performed. Ensure work is
performed by qualified personnel.
WARNING
1492-CM1771-LD008F Conversion Module
Conversion Compatibility
and Product I.D. Label
37-Pin Connector for cable
1492-CONCAB S1
Cable
1492-CONCAB S1

(2)
IV. Conversion Module Wiring Diagram
The following diagram shows the connections from the existing 1771-OBD swing-arm, through the conversion module, 1492
cable and to the two 1756-OC8 output modules. The diagram can be used as an aid in possible system troubleshooting.
Conversion Module Installation and Application Considerations
The 1771-OBD module output current limits versus 1756-OC8 limits are as follows:
1771-OBD 1756-OC8 w/1492-CONCAB005S1
a) Current/Point 2A 2A
b) Current /Module 8A 8A
c) Surge Current /Point 4A for 10ms 4A for 10ms
The 1771-OBD has a single 10A, 250V rectifier fuse (1/4 x 1 1/4 inch ). The 1756-OC8 is NOT fused ,as such a
2AG fuse clip and 10A fuse is provided on the 1492-CM1771-LD008F conversion module.
The 1492-CONCAB005S1 is limited to 3A per pin.
The 1771-OBD is rated 10V to 60V DC. The 1756-OC8 is rated 30V to 60V DC. If the load source voltages is less
than 30V DC, then use 1756-OB16E with the 1492-CM1771-LD006 conversion module.
This configuration uses two(2) 1756-OC8 output modules to replace a single 1771-OBD output module. This may require
the use of a larger 1756 I/O chassis and conversion mounting assembly. Ensure there is sufficient panel space to allow for
this possibility.
Refer to your 1771-OBD and 1756-OC8 Installation Manual wiring schematics and diagrams for more details. Ensure
1756 output module ratings are not exceeded. [Reference Doc: 41170-937 (Version 00)]
There are several key application considerations and system specifications (bottom of drawing) when
using these components (conversion module, cable and output module). Read and understand these
considerations before installation. In addition, refer to the current draw requirements of the existing
loads for this configuration to ensure they are within the current ratings of the 1756 output module.
WARNING
PN-40381
DIR 10000045377 (Version 00)
1492-CONCAB005S1
1492-CM1771-LD008F
Conversion: 1771-OBD to 1756-OC8 Qty. 2 with 1492-CM1771-LD008F
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
37
36
A
B
C
D
01
02
03
04
05
06
07
10
11
12
13
14
15
16
17
00
DC(+)
DC(-)
DC(+)
DC(+)
DC(+)
E
LOAD
+
-Output 01
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 10
Output 11
Output 12
Output 13
Output 14
Output 15
Output 16
Output 17
Output 00
1771-WH, WHF,
WHFB Swing Arm
Green/Black/Orange
Orange/Black/Green
Blue/White/Orange
Black/White/Orange
White/Red/Orange
White/Red/Blue
Orange/Green
Black/White/Red
White/Black/Red
Red/Black/White
Green/Black/White
Orange/Black/White
Blue/Black/White
Black/Red/Green
White/Red/Green
Red/Black/Green
Black
White
Red
Green
Orange
Blue
White/Black
Red/Black
Green/Black
Orange/Black
Blue/Black
Black/White
Red/White
Green/White
Blue/White
Black/Red
White/Red
Orange/Red
Blue/Red
Red/Green
1
3
5
7
4
6
8
10
12
14
16
18
11
13
15
17
20
2
1
3
5
7
4
6
8
10
12
14
16
18
11
13
15
17
20
19
9
19
9
DC-0(+)
OUT-0
OUT-1
OUT-2
OUT-3
DC-0(+)
DC-0(+)
DC-0(+)
RTN OUT-0
DC-1(+)
DC-1(+)
DC-1(+)
DC-1(+)
OUT-4
OUT-5
OUT-6
OUT-7
RTN OUT-1
DC-0(+)
OUT-0
OUT-1
OUT-2
OUT-3
DC-0(+)
DC-0(+)
DC-0(+)
RTN OUT-0
DC-1(+)
DC-1(+)
DC-1(+)
DC-1(+)
OUT-4
OUT-5
OUT-6
OUT-7
RTN OUT-1
RTN OUT-1
RTN OUT-0
RTN OUT-1
RTN OUT-0
2
1756-OC8
1756-OC8
MODULE B MODULE A

(3)
V. Fuse Installation and Replacement
The 1492-CM1771-LD008F conversion module has one mechanical fuse holder with the fuse located on the circuit
board inside the modules plastic case. The following explains how to replace the fuse:
1) Remove the 4 screws that hold both halves of the conversion module case together (refer to the following
Figure A).
2) Disassemble both case halves so you can access the module’s circuit board. Remove and replace the fuse
(refer to the below Figure B).
3) Reassemble the two case halves to the circuit board and replace the four screws that hold the case together
(Do NOT over torque the screws (Maximum torque is 5.0 in-lbs.)
NOTES:
1) For module operation a fuse must be inserted into the fuse holder
2) Physical Fuse Size: 2AG
3) Possible Fuse Supplier: LittelFuse (Part Number: 225010P)
4) Maximum Fuse Current rating based on Conversion System Components: 10.0 Amps
PN-40381
DIR 10000045377 (Version 00)
Fuse holder and Fuse
Figure A
Figure B

(4)
PN-40381
DIR 10000045377 (Version 00)
V. 1492-CM1771-LD008F Conversion Module Specifications
(Operating specifications are when installed in the Conversion System base / cover-plate assembly)
Specification
Dimensions
Approximate Shipping Weight
Storage Temperature -40 to +85°C (-40 to +185°F)
Operating Temperature
0 to 60°C (32 to 140°F)
Operating Humidity 5 to 95% at 60°C (non-condensing)
Shock
Non
-
operating
Operating
50g
30g
Operating Vibration
2g at 10 to 500Hz (Agrees with 1756 I/O module specifications)
Maximum Operating Voltage
60 Vdc
Max. Module Operating Current
Per Point:
Per Module:
2 Amps
8 Amps
Agency Certifications
UL Classified: Under UL File Number E113724
CSA
CE: compliant for all applicable directives
Pollution Degree
2
Environmental Rating
IP20
Refer to the Wiring Diagram(s) for
current limits for a specific configuration.
NOTICE
Value
Fusing One, 10 Amps (maximum current based on conversion components)
11.81 in. (height) x 4.38 in. (depth) x 1.5 in. (width)
300 mm. (height) x 111.25 mm (depth) x 38.1 mm (width)
265.4 g (0.58 lbs) (includes carton)

VII. Appendix A - 1771 chassis to 1756 Chassis Conversion System Selection Process
1) Determine the number of 1771 I/O modules used in the 1771 I/O Chassis to be converted to 1756. NOTE: In some
cases two 1756 modules may be required for one 1771 module. Select the applicable 1492 conversion modules
from the Digital and Analog Conversion Selection Table Matrix.
2) Review the Max Slots for I/O and Chassis Width data from the below table, and select a 1756 I/O Chassis which
meets your conversion needs from Step 1. Ensure the information from the I/O Conversion module tables are
reviewed first.
3) Once the 1756 Chassis is selected, select the Conversion Assembly. The Conversion Assembly has the same
dimensional foot-print as the 1771 chassis and can use the same mounting hardware. The assembly consists of a
base-plate to hold the conversion modules and a cover-plate to protect the modules and to mount the selected
1756 chassis. The combined depth of the conversion assembly with the 1756 chassis mounted is
10.25 inches (Controller w/key) to 10.0 inches (Controller w/o Key).
Foot Notes:
1771-A3B is not listed as it is used for 19 inch wide instrumentation panels
Two 1771 width dimensions are provided as some PLC-5 processors have integrated power supplies. Dimension
w/PS includes -P1, -P2, etc. Notice that the width dimension of some 1756 chassis exceed the width of the 1771
chassis with or without the power supply. Cover-plate chassis mounting design allows the excess 1756 chassis
width to be evenly distributed to both sides, or excess to right or left. Carefully consider this in the conversion
1756-A4 may work in a 1771-A1B application if 4 or less I/O slots were used. Conversion cover-plate is capable to
mount -A4 or -A7
1756-A7 may work in a 1771-A2B application if 6 or less I/O slots were used. Conversion cover-plate is capable to
mount -A7 or -A10
1756-A10 may work in a 1771-A3B1 application if 10 or less I/O slots were used. Conversion cover-plate is capable
to mount -A10 or -A13
1756-A13 may work in a 1771-A4B application if 13 or less I/O slots were used. Conversion cover-plate is capable
to mount -A13 or -A17
(5)
PN-40381
DIR 10000045377 (Version 00)
Max Slots for I/O
4
-A1B w/o
PS
4
-A1B
w/PS
3 6 8 8 69 12
-A13 (5)
12
-A3B1-A10-A7 (4)
-A2B
w/PS
-A2B w/o
PS
-A7-A4 (3)
16
-A17 (6)
16
-A4B
Chassis Width (2)
Conversion Assembly
Chassis Parameter(1)
1756 Equivalent
Chassis
1756 Equivalent
Chassis
24.01 29.0623.1519.0119.029.01 12.61 10.35 14.49 14.4914.01 17.61
1771 Chassis 1771 Chassis
1771 Chassis
1492-MUA1B-A4-A7 1492-MUA2B-A7-A10 1492-MUA3-A10-A13 1492-MUA4-A13-A17
1771 Chassis 1756 Equivalent
Chassis
1756 Equivalent
Chassis

PN-40381
DIR 10000045377 (Version 00)
Printed in U.S.A.
Conversion Module Compatible 1771
Output Module
Compatible 1756
Output Module
Required 1492 Cable
1492-CM1771-
LD008F
1771-OBD Two
1756-OC8
1492-CONCABS1
De-energize and lockout any and all power to all I/O field devices connected to the A-B 1771 I/O
chassis, and the power to the 1771 I/O chassis itself. Ensure all power is de-energized and locked out
to any device in the control cabinet where the conversion is to be performed. Ensure work is
performed by qualified personnel.
WARNING
1492-CONCAB005S1
1492-CM1771-LD008F
Conversion: 1771-OBD to 1756-OC8 Qty. 2 with 1492-CM1771-LD008F
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
37
36
A
B
C
D
01
02
03
04
05
06
07
10
11
12
13
14
15
16
17
00
DC(+)
DC(-)
DC(+)
DC(+)
DC(+)
E
LOAD
+
-Output 01
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 10
Output 11
Output 12
Output 13
Output 14
Output 15
Output 16
Output 17
Output 00
1771-WH, WHF,
WHFB Swing Arm
Green/Black/Orange
Orange/Black/Green
Blue/White/Orange
Black/White/Orange
White/Red/Orange
White/Red/Blue
Orange/Green
Black/White/Red
White/Black/Red
Red/Black/White
Green/Black/White
Orange/Black/White
Blue/Black/White
Black/Red/Green
White/Red/Green
Red/Black/Green
Black
White
Red
Green
Orange
Blue
White/Black
Red/Black
Green/Black
Orange/Black
Blue/Black
Black/White
Red/White
Green/White
Blue/White
Black/Red
White/Red
Orange/Red
Blue/Red
Red/Green
1
3
5
7
4
6
8
10
12
14
16
18
11
13
15
17
20
2
1
3
5
7
4
6
8
10
12
14
16
18
11
13
15
17
20
19
9
19
9
DC-0(+)
OUT-0
OUT-1
OUT-2
OUT-3
DC-0(+)
DC-0(+)
DC-0(+)
RTN OUT-0
DC-1(+)
DC-1(+)
DC-1(+)
DC-1(+)
OUT-4
OUT-5
OUT-6
OUT-7
RTN OUT-1
DC-0(+)
OUT-0
OUT-1
OUT-2
OUT-3
DC-0(+)
DC-0(+)
DC-0(+)
RTN OUT-0
DC-1(+)
DC-1(+)
DC-1(+)
DC-1(+)
OUT-4
OUT-5
OUT-6
OUT-7
RTN OUT-1
RTN OUT-1
RTN OUT-0
RTN OUT-1
RTN OUT-0
2
1756-OC8
1756-OC8
MODULE B MODULE A
Figure A
Figure B
11.81 in. (height) x 4.38 in. (depth) x 1.5 in. (width)
300 mm. (height) x 111.25 mm (depth) x 38.1 mm (width)
265.4 g (0.58 lbs) (includes carton)
1492-CM1771-LD008F Conversion Module
Conversion Compatibility
and Product I.D. Label
37-Pin Connector for cable
1492-CONCAB S1
Cable
1492-CONCAB S1