Allen-Bradley FLEX I/O 1794-IV32 User manual

Installation Instructions
Original Instructions
FLEX I/O Digital Sourcing Input and Sinking
Output Modules
Catalog Numbers 1794-IV32, 1794-OV32
Topic Page
Important User Information 2
Environment and Enclosure 3
North American Hazardous Location Approval 4
Prevent Electrostatic Discharge 5
Install Your Digital Module 7
Configure Your Input Module 12
Configure Your Output Module 13
Specifications 14

2Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid-state Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://www.rockwellautomation.com/literature/) describes some important differences between solid-
state equipment and hard-wired electromechanical devices. Because of this difference, and also because of
the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements that are associated with any particular installation, Rockwell
Automation, Inc. cannot assume responsibility or liability for actual use based on the examples
and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of
Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an
explosion in a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss. Attentions help you identify a
hazard, avoid a hazard and recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor)
to alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to
alert people that surfaces may reach dangerous temperatures.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 3
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Environment and Enclosure
ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1),
at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not
provide adequate protection to radio communication services in such environments.
This equipment is supplied as open-type equipment for indoor use. It must be
mounted within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed to
prevent personal injury resulting from accessibility to live parts. The enclosure
must have suitable flame-retardant properties to prevent or minimize the spread
of flame, complying with a flame spread rating of 5V A or be approved for the
application if nonmetallic. The interior of the enclosure must be accessible only by
the use of a tool. Subsequent sections of this publication may contain more
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the
degrees of protection provided by enclosures.
ATTENTION: Read this document and the documents listed in the Additional
Resources section about installation, configuration, and operation of this
equipment before you install, configure, operate, or maintain this product. Users
are required to familiarize themselves with installation and wiring instructions in
addition to requirements of all applicable codes, laws, and standards.
Installation, adjustments, putting into service, use, assembly, disassembly, and
maintenance are required to be carried out by suitably trained personnel in
accordance with applicable code of practice. In case of malfunction or damage, no
attempts at repair should be made. The module should be returned to the
manufacturer for repair. Do not dismantle the module.

4Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
North American Hazardous Location Approval
The 1794-IV32, 1794-OV32 module is Hazardous Location approved:
The Following Information Applies When
Operating This Equipment In Hazardous Locations.
Informations sur l’utilisation de cet équipement en
environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable
for use in Class I Division 2 Groups A, B, C, D, Hazardous
Locations and nonhazardous locations only. Each product
is supplied with markings on the rating nameplate
indicating the hazardous location temperature code.
When combining products within a system, the most
adverse temperature code (lowest "T" number) may be
used to help determine the overall temperature code of
the system. Combinations of equipment in your system
are subject to investigation by the local Authority Having
Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu'à une utilisation en environnements de Classe
I Division 2 Groupes A, B, C, D dangereux et non dangereux.
Chaque produit est livré avec des marquages sur sa plaque
d'identification qui indiquent le code de température pour les
environnements dangereux. Lorsque plusieurs produits sont
combinés dans un système, le code de température le plus
défavorable (code de température le plus faible) peut être
utilisé pour déterminer le code de température global du
système. Les combinaisons d'équipements dans le système
sont sujettes à inspection par les autorités locales qualifiées
au moment de l'installation.
WARNING:
Explosion Hazard –
• Do not disconnect equipment
unless power has been removed
or the area is known to
be nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is
known to be nonhazardous.
Secure any external connections
that mate to this equipment by
using screws, sliding latches,
threaded connectors, or other
means provided with this product.
• Substitution of components may
impair suitability for Class I,
Division 2.
AVERTISSEMENT:
Risque d’Explosion –
• Couper le courant ou s'assurer que
l'environnement est classé non
dangereux avant de débrancher
l'équipement.
• Couper le courant ou s'assurer que
l'environnement est classé non
dangereux avant de débrancher les
connecteurs. Fixer tous les connecteurs
externes reliés à cet équipement à
l'aide de vis, loquets coulissants,
connecteurs filetés ou autres moyens
fournis avec ce produit.
• La substitution de composants peut
rendre cet équipement inadapté à une
utilisation en environnement de
Classe I, Division 2.
WARNING: When used in a Class I, Division 2, hazardous location, this equipment
must be mounted in a suitable enclosure with proper wiring method that
complies with the governing electrical codes.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 5
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Prevent Electrostatic Discharge
Special Conditions for Safe Use
ATTENTION: This equipment is sensitive to electrostatic discharge, which can
cause internal damage and affect normal operation. Follow these guidelines
when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
ATTENTION:
• This product is grounded through the DIN rail to chassis ground. Use zinc
plated chromate-passivated steel DIN rail to assure proper grounding. The use
of other DIN rail materials (for example, aluminum or plastic) that can corrode,
oxidize, or are poor conductors, can result in improper or intermittent
grounding. Secure DIN rail to mounting surface approximately every 200 mm
(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail
properly. Refer to Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1, for more information.
• Do not remove or replace an Adapter Module while power is applied.
Interruption of the backplane can result in unintentional operation or
machine motion.
• Do not remove or replace a terminal base unit while power is applied.
Interruption of the backplane cab result in unintentional operation or
machine motion.
• If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.

6Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Electrical Safety Considerations
WARNING:
• When you insert or remove the module while backplane power is on, an
electric arc can occur. This could cause an explosion in hazardous
location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
Repeated electric arcing causes excessive wear to contacts on both the module
and its mating connector. Worn contacts may create electrical resistance that
can affect module operation.
• If you insert or remove themodule while backplane power is on, an electric arc
can occur. This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
WARNING:
• Do not connect control circuit directly to line voltage. Line voltage must be
supplied by a suitable, approved isolating transformer or power supply having
short circuit capacity not exceeding 100V A maximum or equivalent.
• If you connect or disconnect wiring while the field-side power is on, an
electrical arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is nonhazardous
before proceeding.
ATTENTION:
• This equipment is certified for use only within the surrounding air temperature
range of 0…55 °C (32…131 °F). The equipment must not be used outside of
this range.
• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any
cleaning agents.
At the end of its life, this equipment should be collected separately from any
unsorted municipal waste.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 7
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Install Your Digital Module
The module mounts on a 1794 terminal base.
1. Rotate the keyswitch (1) on the terminal base (2) clockwise to position 2
as required for this type of module.
2. Ensure that the Flexbus connector (3) is pushed all the way to the left to
connect with the neighboring terminal base/adapter. Yo u c a nn o t i n s t a l l
the module unless the connector is fully extended.
3. Make sure the pins on the bottom of the module are straight so they will
align properly with the connector in the terminal base.
Description Description
1Keyswitch 5Alignmentbar
2Terminalbase 6Groove
3 Flexbus connector 7 Latching mechanism
4Module
ATTENTION: During mounting of all devices, be sure that all debris (metal chips,
wire strands, etc.) is kept from falling into the module. Debris that falls into the
module could cause damage on power up.
1
2
3
45
6
7

8Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
4. Position the module (4) with its alignment bar (5) aligned with the
groove (6) on the terminal base.
5. Press firmly and evenly to seat the module in the terminal base unit. The
module is seated when the latching mechanism (7) is locked into
the module.
Connect Wiring for the1794-IV32 Module (Using a 1794-TB32 or 1794-TB32S
Terminal Base)
1. Connect individual input wiring (0...15) to numbered terminals on the
0...15 row (A) as indicated in the Wiring Connections for 1794-IV32
and 1794-OV32 table.
2. Connect the associated power to the +V1 terminal (35, 37, 39, or 41) on
the 34...51 row (C) as indicated in the Wiring Connections for 1794-
IV32 and 1794-OV32 table.
3. Connect the associated common for inputs 0...15 to COM1 (terminal
36, 38, 40, or 42) on the 34...51 row (C) as indicated in the Wiring
Connections for 1794-IV32 and 1794-OV32 table.
4. Connect individual input wiring (16...31) to numbered terminals on the
16...33 row (B) as indicated in the Wiring Connections for 1794-IV32
and 1794-OV32 table.
Do not connect to terminals 16 or 33.
5. Connect the associated power to the +V2 terminal (43, 45, 47, or 49) on
the 34...51 row (C) as indicated in the Wiring Connections for 1794-
IV32 and 1794-OV32 table.
6. Connect the associated common for inputs 16...31 to COM2 (terminal
44 46, 48, or 50) on the 34...51 row (C).
7. If continuing input wiring power for inputs 0...15 to the next terminal
base, connect a jumper from terminal 41 (+V1) on this terminal base
unit to the power terminal on the next terminal base unit.
8. If continuing input wiring for inputs 0...15 common to the next terminal
base, connect a jumper from terminal 42 (COM1) on this terminal base
unit to the common terminal on the next terminal base unit.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 9
FLEX I/O Digital Sourcing Input and Sinking Output Modules
9. If continuing input wiring power for inputs 16...31 to the next terminal
base, connect a jumper from terminal 49 (+V2) on this terminal base
unit to the power terminal on the next terminal base unit.
10. If continuing input wiring 16...31 common to the next terminal base,
connect a jumper from terminal 50 (COM2) on this terminal base unit
to the common terminal on the next terminal base unit.
Connect Wiring for the1794-OV32 Module
1. Connect individual output wiring (0...15) to numbered terminals on the
0...15 row (A) as indicated in the Wiring Connections for 1794-IV32
and 1794-OV32 table.
2. Connect the associated power to the +V1 terminal (35, 37, 39, or 41) on
the 34...51 row (C) as indicated in the Wiring Connections for 1794-
IV32 and 1794-OV32 table.
3. Connect the associated output common (-V1) for outputs 0...15 to
COM1 (terminal 36, 38, 40, or 42) on the 34...51 row (C).
4. Connect individual output wiring (16...31) to numbered terminals on
the 16...33 row (B) as indicated in the Wiring Connections for 1794-
IV32 and 1794-OV32 table.
5. Connect the associated power to the +V2 terminal (43, 45, 47, or 49) on
the 34...51 row (C) as indicated in the Wiring Connections for 1794-
IV32 and 1794-OV32 table.
6. Connect the associated output common (-V2) for outputs 16...31 to
COM2 (terminals 44, 46, 48, or 50) on the 34...51 row (C).
7. If continuing power to the next terminal base, connect a jumper from
terminal 35, 37, 39, or 41 (+V1) and 43, 45, 47, or 49 (+V2) on this base
unit to the power terminal on the next base unit.
8. If continuing output common return to the next base unit, connect a
jumper from terminal 36, 38, 40, or 42 (COM1) and 44, 46, 48, or 50
(COM2) on this base unit to common on the next base unit (refer to the
installation instructions for the next type of terminal base unit).

10 Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Wiring Connections for 1794-IV32 and 1794-OV32
Channel Signal Channel Signal
0A-0 16B-17
1A-1 17B-18
2A-2 18B-19
3A-3 19B-20
4A-4 20B-21
5A-5 21B-22
6A-6 22B-23
7A-7 23B-24
8A-8 24B-25
9A-9 25B-26
10 A-10 26 B-27
11 A-11 27 B-28
12 A-12 28 B-29
13 A-13 29 B-30
14 A-14 30 B-31
15 A-15 31 B-32
+V1 DC power
(inputs 0...15)
Power terminals 35, 37, 39, and 41 for inputs 0...15.
+V1 connected to terminals 35, 37, 39, and 41.
COM1 DC Return
(inputs 0...15)
Common terminals 36, 38, 40, and 42 for inputs 0...15.
V1 Return connected to terminals 36, 38, 40, and 42.
+V2 DC power(1)
(inputs 16...31
(1) 2-wire input devices use signal and return terminals.
3-wire devices use signal, return, and supply terminals.
Power terminals 43, 45, 47, and 49 for inputs 16...31.
+V2 connected to terminals 43, 45, 47, and 49.
COM2 DC return
(inputs 16...31)
Common terminals 44, 46, 48, and 50 for inputs 16...31.
V2 Return connected to terminals 44, 46, 48, and 50.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 11
FLEX I/O Digital Sourcing Input and Sinking Output Modules
1794-TB32 and 1794-TB32S Terminal Base Wiring for 1794-IV32 and 1794-OV32
2 and 3-Wire Input Wiring for 1794-IV32 and 1794-OV32
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
A
(1794-TB32 shown)
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
NC
B
NC
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Inputs/Outputs - Channels 00-15
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
NC COM1 COM1 COM1 COM1 COM2 COM2 COM2 COM2 NC
C
Inputs/Outputs - Channels 16-31
+V1 +V1 +V1 +V1 +V2 +V2 +V2 +V2
+V1 = Terminals 35, 37, 39 and 41
For 1794-OV32, also use the following as Signal Supply terminals:
For 1794-OV32, also use the following as Signal Supply terminals:
For 1794-IV32, also use the following as Signal return terminals:For 1794-IV32, also use the following as Signal return terminals:
For 1794-OV32 & 1794-IV32For 1794-OV32 & 1794-IV32
+V2 = Terminals 43, 45, 47 and 49
COM1 = Terminals 36, 38, 40 and 42
COM2 = Terminals 44, 46, 48 and 50
NC = No connections (terminals 16, 33, 34 and 51)
0 -15
COM1 / COM 2
16-33
A
B
C
2-Wire Device
COM1 = Terminals C36, C38, C40, and C42
COM2 = Terminals C44, C46, C48, and C50
(1794-OV32 – Sinking Output)
01 0 1
3-Wire Device
0
16
34
(1794-IV32 – Sourcing Input)

12 Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Configure Your Input Module
You configure your input module by setting bits in the configuration word
(word 3).
Set the Input Filter Time for the 1794-IV32 Module
To set the input filter time, set the associated bits in the output image
(complementary word) for the module.
Image Table Memory Map for the 1794-IV32 Module
Dec 1514131211109876543210
Oct 17161514131211107 6 5 4 3 2 1 0
Read1I15I14I13I12I11I10I9I8I7I6I5I4I3I2I1I0
Read 2 I31 I30 I29 I28 I27 I26 I25 I24 I23 I22 I21 I20 I19 I18 I17 I16
Write 1 Not used Input Filter FT
0...31 Not used
Where I = Input
FT = Input filter time
Note: C, CR, and CF not available when used with any series 1794-ASB or -ASB2 Remote I/O Adapters.
O:010
11 10 07 06 05 04 03 02 01 0017 16 15 14 13 12
Octal
09 08 07 06 05 04 03 02 01 0015 14 13 12 11 10
FT = 00...31
Dec.

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 13
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Input Filter Times
Configure Your Output Module
You configure your output module by setting bits in the configuration word
(word 3).
Bits Description Selected Filter Time
10 09 08 Filter Time for Inputs 00...31 Off to On / On to Off
000Filtertime0(default) 0.25ms
001Filtertime1 0.5ms
010Filtertime2 1ms
011Filtertime3 2ms
101Filtertime4 4ms
101Filtertime5 8ms
110Filtertime6 16ms
111Filtertime7 32ms
Image Table Memory Map for the 1794-OV32 Module
Dec 1514131211109876543210
Oct 17161514131211107 6 5 4 3 2 1 0
Read 0 Not used – set to 0
Write1 O15O14O13O12O11O10O9O8O7O6O5O4O3O2O1O0
Write2 O31O30O29O28O27O26O25O24O23O22O21O20O19O18O17O16
Where O = Output

14 Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Specifications
Specifications – FLEX™ I/O Digital Sourcing Input Module
Attribute Value
Number of inputs 32, current, sourcing
Recommended terminal base unit 1794-TB32, 1794-TB32S, 1794-TB62DS, 1794-TB62EXD4X15
On-state voltage, min 19.2V DC
On-state voltage, nom 24V DC
On-state voltage, max 31.2V DC
On-state current, min 2.0 mA
On-state current, nom 4.1 mA @ 24V DC
On-state current, max 6.0 mA
Off-state voltage, max 5V DC
Off-state current, max 1.5 mA
Input impedance 6 kΩ
Isolation voltage
50V (continuous), Basic Insulation Type
Type tested @ 850V DC for 60 s, between field side and system
No isolation between individual channels
Input filter time(1)
Off to On
On to Off
(1) Input off-to-on filter time is the time from a valid input signal to recognition by the module. Input on-to-off filter time is
time from the input signal dropping below the valid level to recognition by the module.
See Input Filter Times table
Flexbus current 40 mA @ 5V DC
Power dissipation, max 6 W @ 31.2V DC
Thermal dissipation, max 20.5 BTU/hr @ 31.2V DC
Specifications – FLEX I/O Digital Sinking Output Module
Attribute Value
Number of outputs 32, current, sinking
Recommended terminal base unit 1794-TB3, 1794-TB3S, 1794-TB3K, 1794-TB3SK
Output voltage, min 10V DC

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 15
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Output voltage, nom 24V DC
Output voltage, max 31.2V DC
Output current rating
14 A max per module
6 A total for channels 0...15
8 A total for channels 16...31
On-state current 1.0 mA min per channel
500 mA max per channel
Surge current 2 A for 50 ms each, repeatable every 2 seconds
Off-state leakage, max 0.5 mA
Isolation voltage
50V (continuous), Basic Insulation Type
Type tested at 707V DC for 60 s, between field side and system
No isolation between individual channels
Output signal delay(1)
Off to On
On to Off
0.5 ms
1.0 ms
Flexbus current 110 mA @ 5V DC
Power dissipation, max 4.4 W @ 31.2V DC
Thermal dissipation, max 8.53 BTU/hr @ 31.2V DC
(1) Delay time is the time from the receipt of an output on or off command to the output actually turning on or off.
General Specifications
Attribute 1794-IV32 1794-OV32
Terminal base screw torque Determined by installed terminal base
Dimensions, approx. (H x W x D) 94 x 94 x 69 mm (3.7 x 3.7 x 2.7 in.)
Indicators (field side) 32 yellow status indicators
External DC power supply voltage, nom 24V DC
External DC power voltage range 19.2...31.2V DC
(includes 5% AC ripple)
10...31.2V DC
(includes 5% AC ripple)
North American temp code T4
Keyswitch position 2
Specifications – FLEX I/O Digital Sinking Output Module
Attribute Value

16 Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Enclosure type rating None (open-style)
Weight, approx. 77 g (2.72 oz) 80 g (2.82 oz)
Wire size Determined by installed terminal base
Wiring category(1) 2 – on signal ports
(1) Use this Conductor Category information for planning conductor routing as described in the appropriate System Level
Installation Manual. Also refer to Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for
more information.
Environmental Specifications
Attribute Value
Operating temperature
IEC 60068-2-1 (Test Ad, operating cold),
IEC 60068-2-2 (Test Bd, operating dry heat),
IEC 60068-2-14 (Test Nb, operating thermal shock):
0…55 °C (32…131 °F)
Storage temperature
IEC 60068-2-1 (Test Ab, unpackaged nonoperating cold),
IEC 60068-2-2 (Test Bb, unpackaged nonoperating dry heat),
IEC 60068-2-14 (Test Na, unpackaged nonoperating thermal shock):
-40…85 °C (-40…185 °F)
Temperature, surrounding air, max 55 °C (131 °F)
Relative humidity IEC 60068-2-30 (Test Db, unpackaged damp heat):
5…95% noncondensing
Vibration IEC60068-2-6 (Test Fc, operating):
5 g @ 10...500 Hz
Shock, operating IEC60068-2-27 (Test Ea, unpackaged shock):
30 g
Shock, nonoperating IEC60068-2-27 (Test Ea, unpackaged shock):
50 g
Emissions IEC 61000-6-4
ESD immunity
IEC 61000-4-2:
6 kV contact discharges
8 kV air discharges
General Specifications
Attribute 1794-IV32 1794-OV32

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 17
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Radiated RF immunity
IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz
10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz
1V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz
EFT/B immunity
IEC 61000-4-4:
±2 kV @ 5 kHz on power ports
±2 kV @ 5 kHz on signal ports
Surge transient immunity IEC 61000-4-5:
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
Certifications
Certifications
(When Product Is
Marked)(1)
Value
c-UL-us
UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for U.S. and Canada.
See UL File E334470.
CE
European Union 2014/30/EU EMC Directive, compliant with:
• EN 61326-1; Meas./Control/Lab., Industrial Requirements
• EN 61000-6-4; Industrial Emissions
• EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2011/65/EU RoHS, compliant with:
• EN 50581; Technical documentation
KC Korean Registration of Broadcasting and Communications Equipment, compliant with:
• Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
RCM Australian Radiocommunications Act, compliant with:
• EN 61000-6-4; Industrial Emissions
(1) See the Product Certification link at http://www.rockwellautomation.com/global/certification/overview.page for
Declaration of Conformity, Certificates, and other certification details.
Environmental Specifications
Attribute Value

18 Rockwell Automation Publication 1794-IN122C-EN-P - July 2018
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Notes:

Rockwell Automation Publication 1794-IN122C-EN-P - July 2018 19
FLEX I/O Digital Sourcing Input and Sinking Output Modules
Rockwell Automation Support
Use the following resources to access support information.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any
suggestions on how to improve this document, complete the How Are We Doing? form
at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-
du002_-en-e.pdf.
Technical Support
Center
Knowledgebase Articles, How-to Videos,
FAQs, Chat, User Forums, and Product
Notification Updates.
www.rockwellautomation.com/
knowledgebase
Local Technical
Support Phone
Numbers
Locate the phone number for your country. www.rockwellautomation.com/global/
support/get-support-now.page
Direct Dial Codes
Find the Direct Dial Code for your product.
Use the code to route your call directly to a
technical support engineer.
www.rockwellautomation.com/global/
support/direct-dial.page
Literature Library Installation Instructions, Manuals,
Brochures, and Technical Data. www.rockwellautomation.com/literature
Product Compatibility
and Download Center
(PCDC)
Get help determining how products interact,
check features and capabilities, and find
associated firmware.
www.rockwellautomation.com/global/
support/pcdc.page

Allen-Bradley, Rockwell Automation, FLEX I/O, Rockwell Software, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: [phone]
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 1794-IN122C-EN-P - July 2018
Supersedes Publication 1794-IN122B-EN-P - August 2015 Copyright © 2018 Rockwell Automation, Inc. All rights reserved.