Allen-Bradley ArmorBlock Series Manual

Wiring Diagrams
ArmorBlock Dual-Port EtherNet/IP 8-Point
Digital Modules
Catalog Numbers 1732E-IB8M8SOER, 1732E-OB8M8SR, 1732E-8CFGM8R
Parts List
Your package contains one 1732E ArmorBlock™ module and these pinout guide
wiring instructions.
For complete installation instructions, refer to the Module Publication Number
table and visit http://literature.rockwellautomation.com.
Module Publication Number
Module Publication Number
1732E ArmorBlock Dual Port EtherNet/IP Digital Modules Installation
Instructions
1732E-IN007
ATTENTION: Two sets of mounting holes are used to mount the module
directly to a panel or machine. Mounting holes accommodate #6 (M3) pan
head screws. The torque specification is 0.68 Nm (6 lb-in.).
ATTENTION: To comply with the CE Low Voltage Directive (LVD), this
equipment and all connected I/O must be powered from a source compliant
with the following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
ATTENTION: To comply with UL restrictions, this equipment must be powered
from a source compliant with the following: Limited Voltage.
ATTENTION: The device meets UL Type 1 Enclosure rating.

2ArmorBlock Dual-Port EtherNet/IP 8-Point Digital Modules
Publication 1732E-WD002C-EN-P - March 2014
I/O Connectors
EtherNet/IP Connector
D-Code M12 Micro Network Female Connector
ATTENTION: Sensors/actuators power should not be supplied externally.
IMPORTANT
Use the 1585D–M4DC–H: Polyamide small body unshielded mating
connectors for the D-Code M12 female network connector.
Note that the distance between the center of each Ethernet connector is
16.2 mm. Rockwell Automation recommends the use of suitable cable
based on this measurement. Some of the recommended cables are
1585D-M4TBJM-x and 1585D-M4TBDM-x for daisychains.
ATTENTION: Make sure all connectors and caps are securely tightened to
properly seal the connections against leaks and maintain IP enclosure type
requirements.
34
1
(View into connector)
Pin 1 Sensor source voltage
Pin 3 Return
Pin 4 Input
45383
Pico-style 3-Pin Input Female Connector
34
1
45383
(View into connector)
Pin 1 Sensor source voltage
Pin 3 Return
Pin 4 Output
Pico-style 3-Pin Output Female Connector
34
1
Pico-style 3-Pin Self-configuring Female Connector
(View into connector)
Pin 1 Sensor source voltage
Pin 3 Return
Pin 4 Input or Output
45383
(View into connector)
Pin 1 Tx+
Pin 2 Rx+
Pin 3 Tx-
Pin 4 Rx-
Pin 5 Shell
4
2
31
5
44808

ArmorBlock Dual-Port EtherNet/IP 8-Point Digital Modules 3
Publication 1732E-WD002C-EN-P - March 2014
Power Connectors
Micro-style 4-Pin Input Male Receptacle
Specifications
IMPORTANT
Use two twisted pair CAT5E UTP or STP cables.
IMPORTANT
The maximum current that any pin on the power connectors can
carry is 4 A.
Environmental Specifications
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…60 °C (-4…140 °F)
Temperature, ambient, max 60 °C (140 °F)
Voltage, power, max 30V DC
Voltage, power, min 12V DC
Output current 0.5A per output, up to 4A per module
D-Code
M12 Pin
Wire Color Signal 8-way Modular
RJ45 Pin
1 White-orange TX+ 1
2 White-green RX+ 3
3 Orange TX- 2
4 Green RX- 6
1
4
3
2
3
4
1
2
45764
(View into receptacle)
Pin 1 Auxiliary power+
Pin 2 Module power+
Pin 3 Module power-
Pin 4 Auxiliary power-
45763
Male Input Female Output

Publication 1732E-WD002C-EN-P - March 2014 PN-245397
Supersedes publication 1732E-WD002B-EN-P - January 2012 Copyright © 2014 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Allen-Bradley, Rockwell Automation, ArmorBlock and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Pilot Duty Rating DC-14
Enclosure type rating Meets IP65/66/67/69K
ATTENTION: This equipment is considered Group 1, Class A industrial equipment
according to IEC/CISPR 11. Without appropriate precautions, there may be difficulties
with electromagnetic compatibility in residential and other environments due to
conducted and radiated disturbance.
Certifications
Certification (when
product is marked)(1)
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
Value
c-UR-us UL Recognized Component Industrial Control Equipment, certified for US
and Canada. See UL File E322657.
CE European Union 2004/108/EC EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
C-Tick Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
EtherNet/IP ODVA conformance tested to Ethernet/IP specifications.
KC Korean Registration of Broadcasting and Communications Equipment,
compliant with:
Article 58-2 of Radio Waves Act, Clause 3
Environmental Specifications
Attribute Value