Allen + Roth 0731353 User manual

allenandroth.com
VANITY WITH TOP
ITEM #0731353
MODEL #1212VA-30-201
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 1-866-439-9800,
8 a.m. - 8 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Français p. 8
Español p. 15
allen + roth®is a registered trademark
of LF, LLC. All Rights Reserved.
EB16182
welcoming • sophisticated • inspiring
1

allenandroth.com
2
PACKAGE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install this
product.
WARNING
• Some steps are more easily handled with two adults.
•Assembly and unpacking requires two adults.
CAUTION
• DO NOT try to pry off top from vanity. Damage to top or vanity may occur.
• Use care when assembling the vanity; take your time and follow the assembly instructions closely.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HARDWARE CONTENTS
Touch-Up Pen
Qty. 1
AA
PART DESCRIPTION QUANTITY
A Vanity 1
B Top (preassembled
to Vanity (A))
1
CBacksplash 1
A
B
C
AA

allenandroth.com
3
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Installation Time: 20-30 minutes (24 hours for adhesive to dry).
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, adhesive,
power drill with drill bit
Helpful Tools (not included): Measuring tape, level
INSTALLATION INSTRUCTIONS
1
A
1
2
1. To remove drawers preassembled in vanity (A),
fully extend drawers. Locate plastic tabs on metal
glide tracks at left and right sides of drawer box.
To disengage drawer box from glides, pull out
plastic tabs from glide toward center of drawer.
Then, gently lift drawer up to remove it from
vanity (A).

allenandroth.com
4
INSTALLATION INSTRUCTIONS
1
2
2
3
A
B
3. From inside vanity (A), drill hole through vanity
mounting area and into wall studs. Using
mounting hardware (not included) appropriate
for your installation site, secure vanity (A) to wall
stud. If possible, secure vanity (A) to two wall
studs for increased stability.
3
A
Note: Clean area where the vanity (A) will be
permanently located prior to beginning installation,
ensuring the vanity (A) will not interfere with any water
supply and drain lines once mounted.
2. With two people, carefully place vanity (A) with
and mark locations of wall studs behind the
permanent location of vanity (A).
Note: Use preassembled levelers on legs of
vanity (A) to level the item. Twisting the levelers
counterclockwise will increase the height of vanity (A),
twisting them clockwise will decrease it.
WARNING
Vanity (A) MUST be secured to wall.

allenandroth.com
5
4
2
A
1
3
INSTALLATION INSTRUCTIONS
4. To reinstall drawer into vanity (A), fully extend
metal glide tracks. Gently lower and slide drawer
box into rear glide catch. Next lower drawer box
down to completely rest on extended glides.
Then, push back in the left and right plastic tabs
to lock the drawer box in place.
Repeat for remaining drawer.
CAUTION
DO NOT force drawer or damage to glide may
occur. If drawer does not slide in with ease,
remove and try again from the start.
22
5
1
C
B
5. Apply adhesive (not included) to unpolished
side and bottom of backsplash (C). Position
backsplash (C) on top (B) and against wall.
Clean any excess adhesive before allowing
to dry.
Assembly is now complete. Install desired faucet
and drain assemblies (neither included) per the
manufacturers' instructions to complete
the installation.

allenandroth.com
6
WARRANTY
The manufacturer warrants this item against defects in materials and workmanship for a period of one
(1) year from the date of original retail purchase. This warranty applies only to the original purchaser.
. The manufacturer
is not accountable whatsoever for product installation during the warranty period. There is no further
expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential
or special damages arising at or in connection with product use or performance except as may
otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.
CARE AND MAINTENANCE
• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local
supplier.
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch. Rub off excess
colorant promptly with a soft cloth.
IMPORTANT
• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble,
engineered stone). Stone tops will vary from product to product. Use caution when placing items
such as soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar
item to protect the surface if placing any soap or fragranced products on the stone.
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and
dry using a soft non-abrasive cloth.
• Stone care products are available at your local home center store. Follow the manufacturer's
directions on how to use.
• DO NOT use products to clean the stone top that contain acetone, lemon, vinegar or other acids as
these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home
store. Follow the manufacturer's directions on how to apply.

allenandroth.com
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST,
Monday - Friday.
Printed in China
allen + roth®is a registered trademark of
LF, LLC. All Rights Reserved.
C
F
E
D
BB
AA
CC
PART DESCRIPTION PART #
CBacksplash PF-1012VA-30-201-001
DDrawer Divider PF-1012VA-30-201-002
ETop Divided Drawer PF-1012VA-30-201-003
FBottom Drawer PF-1012VA-30-201-004
AA Touch-Up Pen OF-0010 (W2108)
BB Glide Track Set 663BH-12
CC Drawer Pull CF-001-BN
7

allenandroth.com
8
MEUBLE-LAVABO AVEC COMPTOIR
ARTICLE #0731353
MODÈLE #1212VA-30-201
Numéro de série Date d’achat
Desquestions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant,
appelez notre service à la clientèle au 1 866 439-9800, entre 8 h et 20 h (HNE), du lundi au vendredi.
JOIGNEZ VOTRE REÇU ICI
allen + roth® est une marque de commerce
déposée de LF, LLC. Tous droits réservés.
welcoming • sophisticated • inspiring

allenandroth.com
9
CONSIGNES DE SÉCURITÉ
Assurez-vous de lire et de comprendre l’intégralité de ce manuel avant de tenter d’assembler, d’installer
ou d’utiliser le produit.
AVERTISSEMENT
• Certaines étapes sont plus faciles à effectuer avec l’aide d’un deuxième adulte.
• L’assemblage et le déballage nécessitent deux adultes.
ATTENTION
• Ne tentez pas de retirer le comptoir du meuble-lavabo; vous risqueriez d’endommager le comptoir
ou le meuble-lavabo.
• Soyez prudent lors de l’assemblage du meuble-lavabo; prenez votre temps et suivez minutieuse-
ment les instructions pour l’assemblage.
VEUILLEZ CONSERVER CES INSTRUCTIONS POUR VOUS Y RÉFÉRER ULTÉRIEUREMENT.
QUINCAILLERIE INCLUSE
Crayon à retouche
Qté : 1
AA
PIÈCE DESCRIPTION QUANTITÉ
A Meuble-lavabo 1
BComptoir (préassemblé
au meuble-lavabo [A])
1
CDosseret 1
A
B
C
AA
CONTENU DE L’EMBALLAGE

allenandroth.com
10
PRÉPARATION
Avant de commencer l’assemblage de l’article, assurez-vous d’avoir toutes les pièces. Comparez le
contenu de l’emballage avec la liste des pièces et celle de la quincaillerie incluse. S’il y a des pièces
manquantes ou endommagées, ne tentez pas d’assembler l’article.
Temps d’installation approximatif : 20 à 30 minutes (24 heures pour le séchage de l’adhésif).
Outils nécessaires pour l’installation (non inclus) : tournevis cruciforme, couteau à lame rétractable ou
ciseaux, adhésif, perceuse électrique et foret.
Outils utiles (non inclus) : ruban à mesurer et niveau.
INSTRUCTIONS POUR L’INSTALLATION
1
A
1
2
1. Pour enlever les tiroirs préassemblés du
meuble-lavabo (A), ouvrez-les complètement.
Repérez les languettes de plastique sur les
glissières en métal posées de chaque côté du
tirez sur les languettes de plastique des
glissières vers le centre du tiroir. Ensuite,
soulevez délicatement le tiroir pour le retirer du
meuble-lavabo (A).