Alliance Laundry Systems JT30XG Owner's manual

Installation/Operation/Maintenance
Drying Tumblers
30 Pound Capacity (28" Wide)
30 Pound Capacity (31.5" Wide)
50 Pound Capacity
75 Pound Capacity
120 Pound Capcity
170 Pound Capacity
Model Numbers in this manual
are shown on page 5
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
(If this tumbler changes ownership, be sure this manual accompanies
the tumbler.)
Part No. M413620R3
November 1998
NOTA: El manual en
español aparace después
del manual en inglés.

M413620 1
TABLE OF CONTENTS
SECTION I
SAFETY
Important Safety Instructions . . . . . . . . . . . . . . . . . . 5
SECTION II
INTRODUCTION
Information For Handy Reference . . . . . . . . . . . . . . 7
Nameplate Location . . . . . . . . . . . . . . . . . . . . . . . . . 8
Replacement Parts Information . . . . . . . . . . . . . . . . 8
Cabinet Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 9
Exhaust Thimble Locations. . . . . . . . . . . . . . . . . . . . 10
Steam Connection Locations. . . . . . . . . . . . . . . . . . . 11
Gas Connection Locations . . . . . . . . . . . . . . . . . . . . 12
Electrical Connection Locations . . . . . . . . . . . . . . . . 13
Tumbler Specifications . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION III
INSTALLATION INSTRUCTIONS
Receiving Inspection. . . . . . . . . . . . . . . . . . . . . . . . . 23
Materials Required (Obtain Locally) . . . . . . . . . . . . 23
Positioning the Drying Tumbler . . . . . . . . . . . . . . . . 24
Leveling the Drying Tumbler . . . . . . . . . . . . . . . . . . 24
Drying Tumbler Enclosure Construction . . . . . . . . . 25
Facilities Required. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Make-Up Air. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Steam Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 37
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . 42
Accessory Timing Cam Installation . . . . . . . . . . . . . 49
Preliminary Operating Checks . . . . . . . . . . . . . . . . . 50
Final Operating Checks . . . . . . . . . . . . . . . . . . . . . . 51
SECTION IV
ADJUSTMENTS
Main Gas Burner Air Shutter. . . . . . . . . . . . . . . . . . . 53
Air Flow Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Air Flow Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Cylinder Door Switch . . . . . . . . . . . . . . . . . . . . . . . . 58
Cylinder Door Strike . . . . . . . . . . . . . . . . . . . . . . . . . 58
Cylinder Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SECTION V
OPERATING INSTRUCTIONS
Manual Dual Timer Tumbler . . . . . . . . . . . . . . . . . . . 66
Coin-Operated Tumbler. . . . . . . . . . . . . . . . . . . . . . . 67
Electronically Controlled OPL Tumbler . . . . . . . . . . 69
SECTION VI
PREVENTIVE MAINTENANCE
INSTRUCTIONS
Daily. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Lint Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Monthly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Lint Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Every Three Months . . . . . . . . . . . . . . . . . . . . . . . . . 81
Lint Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Belt Tension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Every Six Months . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Overall Check . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Maintenance Check Chart . . . . . . . . . . . . . . . . . . . . . 82
Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Service Savers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Troubleshooting the Tumbler. . . . . . . . . . . . . . . . . . . 84
©Copyright 1998, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means
without the expressed written consent of the publisher.

2M413620
Notes

M413620 3
SECTION I
Safety
IMPORTANT: Warranty is void unless drying tumbler is installed according to instructions in this manual.
Compliance with minimum specifications and requirements detailed herein, and with applicable local gas fitting
regulations, municipal building codes, water supply regulations, electrical wiring regulations, and any other
relevant statutory regulations. Because of varied requirements, applicable local codes should be thoroughly
understood and all pre-installation work arranged for accordingly.
In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1 “National
Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code”.
In Canada, installation must comply with Standards CAN1-B149.1 or CAN1-B149.2 codes for gas burning
appliances and equipment and CSA C22.1, latest edition, Canadian Electric Code, Part I.
In Australia, installation must comply with the Australian Gas Association Installation Code for Gas Burning
Appliances and Equipment.
NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution and
carefulness are factors which CANNOT be built into this tumbler. These factors MUST BE supplied by the
person(s) installing, maintaining or operating the tumbler.
Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do
not understand.
Failure to install, maintain, and/or operate this machine according to manufacturer’s
instructions may result in conditions which can produce serious injury, death and/or
property damage. W051
WARNING

4M413620
IMPORTANT: Information must be obtained from your local gas supplier on instructions to be followed if the
user smells gas. These instructions must posted in a prominent location. Step-by-step instructions of the safety
information below must be posted in a prominent location near the tumbler for customer use.
FOR YOUR SAFETY, the information in
this manual must be followed to minimize
the risk of fire or explosion or to prevent
property damage, personal injury or
death. W033
WARNING
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do not
use any phone in your building.
– Clear the room, building or area of all
occupants.
– Immediately call your gas supplier from a
neighbor’s phone. Follow the gas
supplier’s instructions.
– If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be performed
by a qualified installer, service agency or
the gas supplier. W052
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.W053
AVERTISSEMENT
Assurez-vous de bien suivre les
instructions données dans cette notice
pour réduire au minimum le risque
d’incendie ou d’explosion ou pour
éviter tout dommage matérial, toute
blessure ou la mort. W033Q
• Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables
dans le voisinage de cet appareil ou de
tout autre appareil.
• QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ
– Ne pas tenter d’allumer d’apareil.
– Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant
dans le bâtiment où vous vous trouvez.
– Évacuez la pièce, le bâtiment ou la zone.
– Appelez immédiatement votre
fournisseur de gas depuis un voisin.
Suivez les instructions du fournisseur.
– Si vous ne pouvez rejoindre le
fournisseur de gas, appelez le service
des incendies.
• L’installation et l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz. W052Q
POUR VOTRE SÉCURITÉ
Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables dans le voisinage de cet
appareil ou de tout autre appareil. W053Q

M413620 5
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
1. Read all instructions before using the tumbler.
2. Refer to the GROUNDING INSTRUCTIONS for the proper grounding of the tumbler.
3. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.
4. Do not allow children to play on or in the tumbler. Close supervision of children is necessary when the tumbler is
used near children. This is a safety rule for all appliances.
5. Before the tumbler is removed from service or discarded, remove the door to the drying compartment.
6. Do not reach into the tumbler if the cylinder is revolving.
7. Do not install or store the tumbler where it will be exposed to water and/or weather.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the tumbler, or attempt any servicing unless specifically recommended in the
User-Maintenance instructions or in published user-repair instructions that you understand and have the skills to
carry out.
10. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric
softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured
rubberlike materials.
12. Always clean the lint filter before every load. A layer of lint in the filter reduces drying efficiency and prolongs
drying time.
13. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and
dirt.
14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel.
15. If not installed, operated and maintained in accordance with the manufacturer’s instructions or if there is damage to
or mishandling of this product’s components, use of this product could expose you to substances in the fuel or from
fuel combustion which can cause death or serious illness and which are known to the State of California to cause
cancer, birth defects or other reproductive harm.
16. Tumbler will not operate with the loading door open. DO NOT bypass the door safety switch by permitting the
tumbler to operate with the door open. The tumbler will stop tumbling when the door is opened. Do not use the
tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing or turning the
START mechanism. Remove the tumbler from use and call the serviceman. Tumbler will not operate with lint
panel open. DO NOT bypass lint panel safety switch by permitting the tumbler to operate with the lint panel open.
To reduce the risk of fire, electric shock, serious injury or death to persons when using
your tumbler, follow these basic precautions: W054
WARNING

6M413620
17. Do not put articles soiled with vegetable or cooking oil in the tumbler, as these oils may not be removed during
drying. Due to the remaining oil, the fabric may catch on fire by itself.
18. To reduce the risk of fire, DO NOT put clothes which have traces of any flammable substances such as machine
oil, flammable chemicals, thinner, etc. or anything containing wax or chemicals such as in mops and cleaning
cloths, or anything dry-cleaned at home with a dry-cleaning solvent in the tumbler.
19. Use the tumbler only for its intended purpose, drying fabrics.
20. ALWAYS disconnect the electrical power to the tumbler before servicing. Disconnect power by shutting off
appropriate breaker or fuse.
21. Install this tumbler according to these INSTALLATION INSTRUCTIONS. All connections for electrical power,
grounding, and gas supply must comply with local codes and be made by licensed personnel when required. Do not
do it yourself unless you know how!
22. Remove laundry immediately after the tumbler stops.
23. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings
or precautions. To reduce the risk of poisoning or chemical burns, keep them out of reach of children at all times
(preferably in a locked cabinet).
24. Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the
cylinder with a damp cloth to remove particles of fiberglass.
25. Always follow the fabric care instructions supplied by the garment manufacturer.
26. Never operate the tumbler with any guards and/or panels removed.
27. DO NOT operate the tumbler with missing or broken parts.
28. DO NOT by-pass any safety devices.
29. Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in
conditions which can produce bodily injury and/or property damage.
30. Run tumbler with a load before putting tumbler into service.
This machine is intended for commercial use.
To reduce the risk of serious injury, install lockable door(s) to prevent public access to
rear of tumblers. W055
WARNING

M413620 7
SECTION II
Introduction
Information in this manual is applicable to these tumbler models.
INFORMATION FOR HANDY REFERENCE
Date Purchased _________________________________________________________
Model No. _________________________ Serial No. __________________________
Dealer’s Name _________________________________________________________
NOTICE: For your own convenience and protection, record the above
information and retain your sales slip for this appliance. The model and serial
numbers will be found on the nameplate located on the tumbler, see Figure 1.
30 Pound
(28" Wide) 30 Pound (31.5" Wide) 50 Pound 75 Pound 120 Pound 170 Pound
JT30XG
JT30WE JT30CG STB30CG
JTB30CG
DTB30CG
JT30EG
STB30EG
JTB30EG
DTB30EG
JT30CE
STB30CE
JTB30CE
DTB30CE
JT30CSH
STB30CSH
JTB30CSH
DTB30CSH
JT30CSL
STB30CSL
JTB30CSL
DTB30CSL
JT50CG
STB50CG
JTB50CG
DTB50CG
JT50EG
STB50EG
JTB50EG
DTB50EG
JT50CE
STB50CE
JTB50CE
DTB50CE
JT50CSH
STB50CSH
JTB50CSH
DTB50CSH
JT50CSL
STB50CSL
JTB50CSL
DTB50CSL
JT75CG
STB75CG
JTB75CG
DTB75CG
JT75EG
STB75EG
JTB75EG
DTB75EG
JT75CE
STB75CE
JTB75CE
DTB75CE
JT75CSH
STB75CSH
JTB75CSH
DTB75CSH
JT75CSL
STB75CSL
JTB75CSL
DTB75CSL
STB634
DTB634
ST120FG
JT120FG
DT120FG
ST120CSH
JT120CSH
DT120CSH
ST170FG
JT170FG
DT170FG
ST170CSH
JT170CSH
DT170CSH
Conversion Table
Multiply By To Obtain Multiply By To Obtain
BTU .252 kCal Pounds / sq. in. .06895 Bars
BTU 1055 Joules Pounds / sq. in. .070 kg / sq. cm.
Inch 2.54 Centimeters Pounds (lbs.) .454 Kilograms
Inches W.C. .036 Pounds / sq. in. Boiler Horsepower 33479 BTU
Inches W.C. .249 kPa Boiler Horsepower 34.5 lbs. Steam / hr.
lbf / inch2(psi) .0369 kPa CFM .471 liters / second
ft328.32 Liters KW 3414 BTU / hr.

8M413620
NAMEPLATE LOCATION
Figure 1
PARTS ORDERING INFORMATION
If literature or replacement parts are required, contact the source from whom the machine was purchased or contact
Alliance Laundry Systems at [phone] for the name and address of the nearest authorized parts distributor. For
technical assistance, call [phone].
T276IE3B T238IE3B
JUNCTION BOX
COVER
INFORMATION
When writing for information
on any tumbler, be sure to
mention model and serial
numbers. The model and serial
numbers will be found on
the nameplate as shown.
T228IE3D
T281IE3B
JUNCTION
BOX
COVER
FOR THE
120 POUND
TUMBLER
FOR THE
170 POUND
TUMBLER
FOR THE 30, 50
AND 75 POUND
TUMBLER

M413620 9
Roughing-In Dimensions and Specifications
Cabinet Dimensions
* See Section III “Positioning the Drying Tumbler” for temporarily reducing the height of these models.
OPENING
CLEARANCE
HEIGHT
WIDTH
T326IE3A
DEPTH
TUMBLER MODELS OVERALL DOOR
HEIGHT WIDTH DEPTH OPENING CLEARANCE
30XG/30WE 72-1/4" (1835 mm) 28" (711 mm) 44-7/8" (1140 mm) 26-3/4" (679 mm) 30-3/4" (781 mm)
30CG/30EG 72-1/4" (1835 mm) 31-1/2" (800 mm) 46-11/16" (1186 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
30CE/30CSH 72-1/4" (1835 mm) 31-1/2" (800 mm) 44-7/8" (1140 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
30CSL 72-1/4" (1835 mm) 31-1/2" (800 mm) 45-1/32" (1144 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
50CG/50EG/50CE 76-5/8" (1946 mm) 38-5/8" (981 mm) 47" (1194 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
50CSL/50CSH 80" (2032 mm) 38-5/8" (981 mm) 47" (1194 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
75CG/75EG/75CE/634 76-5/8" (1946 mm) 38-5/8" (981mm) 53" (1346 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
75CSL/75CSH 80" (2032 mm) 38-5/8" (981 mm) 53" (1346 mm) 28-1/4" (717 mm) 30-3/4" (781 mm)
120FG*/120CSH* 85-1/2" (2172 mm) 46-1/2" (1181 mm) 65" (1235 mm) 30-1/2" (775 mm) 31-5/16" (795 mm)
170FG*/170CSH* 94" (2390 mm) 53-1/8" (1349 mm) 66-1/8" (1679 mm) 30-1/2" (775 mm) 33-5/16" (857 mm)

10 M413620
Roughing-In Dimensions and Specifications
Exhaust Thimble Locations
HEIGHT
ACROSS
T327E3A
ACROSS
ACROSS
ACROSS
DEPTH
DEPTH
HEIGHT
30XG, 30WE & 75EG
120FG, 120CSH,
170FG & 170CSH
TUMBLER MODELS HORIZONTAL EXHAUST VERTICAL EXHAUST
DIAMETER ACROSS HEIGHT DIAMETER ACROSS HEIGHT
30XG/30WE N/A N/A N/A 6" (152 mm) 3-3/8" (86 mm) 3-3/8" (86 mm)
30CG/30CE
30CSL/30CSH 8" (203 mm) 4-7/16" (113 mm) 21-7/8" (556 mm) N/A N/A N/A
30EG 8" (203 mm) 4-7/16" (113 mm) 55-3/8" (1407 mm) N/A N/A N/A
50CG/50CE
50CSL/50CSH 8" (203 mm) 5-3/8" (137 mm) 13-3/8" (340 mm) N/A N/A N/A
50EG 8" (203 mm) 5-3/8" (137 mm) 57-5/8" (1464 mm) N/A N/A N/A
75CG/75CE
75CSL/75CSH 8" (203 mm) 5-3/8" (137 mm) 13-3/8" (340 mm) N/A N/A N/A
75EG N/A N/A N/A 8" (203 mm) 5-5/8" (143 mm) 5" (127 mm)
634 10" (254 mm) 6-1/2" (165 mm) 6-1/2" (165 mm) N/A N/A N/A
120FG/120CSH N/A N/A N/A 10" (254 mm) 203 mm (8") 7-1/2" (185 mm)
170FG/170CSH N/A N/A N/A 12" (305 mm) 7" (178 mm) 9-3/8" (238 mm)

M413620 11
Roughing-In Dimensions and Specifications
Steam Connection Locations
ACROSS
T328E3A
STEAM
OUTLET
HEIGHT
SPAN
STEAM
INLET
HEIGHT
TUMBLER
MODELS STEAM INLET STEAM OUTLET
DIAMETER ACROSS HEIGHT SPAN DIAMETER ACROSS HEIGHT SPAN
30CSL
30CSH 3/4" (19 mm) I.D. 14" (356 mm) 68-3/4" (1746 mm) 7-1/2" (190 mm) 3/4" (19 mm) I.D. 14" (356 mm) 61-1/4" (1556 mm) 7-1/2" (190 mm)
50CSL
50CSH 3/4" (19 mm) I.D. 15-1/4" (387 mm) 72-3/4" (1848 mm) 7-1/2" (190 mm) 3/4" (19 mm) I.D. 15-1/4" (387 mm) 64-3/4" (1645 mm) 7-1/2" (190 mm)
75CSL
75CSH 3/4" (19 mm) I.D. 15-1/4" (387 mm) 72-3/4" (1848 mm) 7-1/2" (190 mm) 3/4" (19 mm) I.D. 15-1/4" (387 mm) 64-3/4" (1645 mm) 7-1/2" (190 mm)
120CSH 3/4" (19 mm)
I.D. 21-1/4" (540 mm) 82-3/4" (2102 mm) N/A (Manifold) 1" (25 mm) N.P.T. 11-7/8" (302 mm) 68-1/2" (1739 mm) 21-1/2" (546 mm)
170CSH 3/4" (19 mm)
I.D. 15-3/4" (400 mm) 88" (2235 mm) 21-5/8" (549 mm) 1" (25 mm) N.P.T. 8-3/4" (222 mm) 71-3/4" (1822 mm) 35-5/8" (905 mm)

12 M413620
Roughing-In Dimensions and Specifications
Gas Connection Locations
ACROSS
T329E3A
HEIGHT
TUMBLER
MODELS GAS CONNECTION
DIAMETER (N.P.T.) ACROSS HEIGHT
30XG 1/2" (12.7 mm) 12-1/4" (311 mm) 62-1/8" (1578 mm)
30CG/30EG 1/2" (12.7 mm) 15" (381 mm) 62-1/8" (1578 mm)
50CG/50EG 1/2" (12.7 mm) 15-1/2" (394 mm) 65-3/4" (1670 mm)
75CG/75EG 1/2" (127 mm) 15-3/4" (400 mm) 65-3/4" (1670 mm)
634 3/4" (19 mm) 15-3/4" (400 mm) 65-3/4" (1670 mm)
120FG 3/4" (19 mm) 33-1/2" (851 mm) 70-1/4" (1784 mm)
170FG 1" (25 mm) 38-5/8" (979 mm) 77-3/8" (1965 mm)

M413620 13
Roughing-In Dimensions and Specifications
Electrical Connection Locations
NOTE: These are approximate dimensions only.
ACROSS
T330iE3A
HEIGHT
ACROSS
HEIGHT
Gas & Steam Electric
TUMBLER
MODELS ELECTRICAL SERVICE - GAS & STEAM MODELS ELECTRICAL SERVICE - ELECTRIC MODELS
HEIGHT ACROSS HEIGHT ACROSS
30XG/30CG/30EG 65" (1651 mm) 3" (76 mm) N/A N/A
30WE N/A N/A 60" (1524 mm) 14" (356 mm)
30CE N/A N/A 60" (1524 mm) 16" (406 mm)
30CSL/30CSH 65" (1651 mm) 3" (76 mm) N/A N/A
50CG/50EG 68" (1727 mm) 3" (76 mm) N/A N/A
50CE N/A N/A 64" (1626 mm) 19" (483 mm)
50CSL/50CSH 68" (1727 mm) 3" (76 mm) N/A N/A
75CG/75EG 68" (1727 mm) 3" (76 mm) N/A N/A
75CE N/A N/A 64" (1626 mm) 19" (483 mm)
75CSL/75CSH/634 68" (1727 mm) 3" (76 mm) N/A N/A
120FG/120CSH 65" (1651 mm) 24" (610 mm) N/A N/A
170FG/170CSH 68" (1727 mm) 27" (686 mm) N/A N/A

14 M413620
30 Pound, 28" wide Gas Tumbler
30 Pound, 28" wide Electric Tumbler
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 26.5" x 30" (67.3 cm x 76.2 cm)
perforated galvanized steel with three baffles
Motor: 1/3 H.P., lifetime lubricated, internal overload protected
Gas Consumption: 75,000 BTU per hour (79.1 MJ/hr.)
Max. Air Flow: 370 C.F.M. (175 liters/sec.)
Net Weight: 350 Pounds (159 kg) (approximate)
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 26.5" x 30" (67.3 cm x 76.2 cm)
perforated galvanized steel with three baffles
Motor: 1/3 H.P., lifetime lubricated, internal overload protected
Element: 21,000 Watts (60 Hz models)
Long life nichrome wire
18,000 Watts (50 Hz models)
Max. Air Flow: 625 C.F.M. (295 liters/sec.)
Net Weight: 410 Pounds (184.5 kg) (approximate)

M413620 15
30 Pound Gas Tumbler
30 Pound Electric Tumbler
30 Pound Steam Tumbler
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 30" x 30" (76.2 cm x 76.2 cm) perforated galvanized steel with three baffles;
30 pounds (13.6 kg) dry weight (cotton load)
Motor: 1/3 H.P., lifetime lubricated, internal overload protected
Gas Consumption: Energy Saver Models — 80,000 BTU per hour (84.4 MJ/hr.)
Standard Models — 105,000 BTU per hour (110.8 MJ/hr.)
Gas Connection: 1/2 inch N.P.T.
Max. Air Flow: Energy Saver Models — 250 C.F.M. (118 liters/sec.)
Standard Models — 625 C.F.M. (295 liters/sec.)
Net Weight: 450 Pounds (204 kg) (approximate)
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 30" x 30" (76.2 cm x 76.2 cm) perforated galvanized steel with three baffles;
30 pounds (13.6 kg) dry weight (cotton load)
Motor: 1/3 H.P., lifetime lubricated, internal overload protected
Element: 21,000 Watts (all voltages)
Max. Air Flow: 625 C.F.M. (295 liters/sec.)
Net Weight: 450 Pounds (204 kg) (approximate)
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 30" x 30" (76.2 x 76.2 cm) perforated galvanized steel with three baffles;
30 pounds dry weight (13.6 kg) (cotton load)
Motor: High Pressure (4 coils) 1/2 H.P.
Low Pressure (4 coils) 3/4 H.P.
Boiler Horsepower: 4 coil High Pressure – 3.7 Bhp (123,950 BTU/hr., 58 kg/hr, 31,235 kCal/hr.)
4 coil Low Pressure – 2.6 Bhp (87,100 BTU/hr., 40 kg/hr, 21,949 kCal/hr.)
Max. Air Flow: 625 C.F.M. (295 liters/sec.)
Net Weight: 470 Pounds (214 kg) (approximate)

16 M413620
50 Pound Gas Tumbler
50 Pound Electric Tumbler
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 37" x 30" (94 cm x 76.2 cm) perforated galvanized steel with four baffles;
50 pounds (22.7 kg) dry weight (cotton load)
Motor:
(Nonreversing Models) 1/2 H.P., lifetime lubricated, internal overload protected (See below for reversing models.)
Gas Consumption: Energy Saver Models — 95,000 BTU per hour (100.2 MJ/hr.)
Standard Models — 120,000 BTU per hour (126.6 MJ/hr.)
Max. Air Flow: Energy Saver Models — 390 C.F.M. (184 liters/sec.)
Standard Models — 750 C.F.M. (354 liters/sec.)
Net Weight: 545 Pounds (247 kg) (approximate)
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 37" x 30" (94 cm x 76.2 cm) perforated galvanized steel with four baffles;
50 pounds (22.7 kg) dry weight (cotton load)
Motor:
(Nonreversing Models) 1/2 H.P., lifetime lubricated, internal overload protected (See below for reversing models.)
Element: 21,000 watts (240 VAC 50 Hz.) Long life nichrome wire
30,000 watts (all other voltages) Long life nichrome wire
Max. Air Flow: 750 C.F.M. (354 liters/sec.)
Net Weight: 550 Pounds (250 kg) (approximate)

M413620 17
50 Pound Steam Tumbler
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 37" x 30" (94 x 76.2 cm) perforated galvanized steel with four baffles;
50 pounds (22.7 kg) dry weight (cotton load)
Motor:
(Nonreversing Models) High Pressure Steam — 1/2 H.P.
Low Pressure Steam — 3/4 H.P
Both motors are lifetime lubricated, internal overload protected
See below for reversing models.
Boiler Horsepower: High Pressure Steam (6 Coil) — 4.60 B.H.P.
Low Pressure Steam (4 Coil) — 3.00 B.H.P.
Max. Air Flow: 750 C.F.M. (354 liters/sec)
Net Weight: 4 Coil Tumbler — 565 pounds (257 kg) (approximate)
6 Coil Tumbler — 580 pounds (263 kg) (approximate)
REVERSING MOTOR SIZES
GAS ELECTRIC STEAM
HIGH
PRESSURE LOW
PRESSURE
50 LB. FAN 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/2 H.P.
CYLINDER 1/3 H.P. 1/3 H.P. 1/3 H.P. 1/3 H.P.

18 M413620
75 Pound Gas Tumbler
75 Pound, Electric, Non-reversing Tumbler
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 37" x 36" (94 x 91.4 cm) perforated galvanized steel cylinder with four baffles;
75 pounds (34.1 kg) dry weight (cotton load)
Motor: 3/4 H.P., lifetime lubricated, internal overload protected. See below for
reversing models.
Gas Consumption: Standard Models: 165,000 B.T.U. per hour (174.1 MJ/hr.) Energy Saver Models: 140,000 B.T.U. per hour (147.7 MJ/hr.)
DTB634 Models: 215,000 B.T.U. per hour (227 MJ/hr.)
Max. Air Flow: Standard Models: 920 C.F.M. (434 liters/sec.)
Energy Saver Model: 500 C.F.M. (236 liters/sec.)
634 Models: 1100 C.F.M. (519 liters/sec.)
Net Weight: 575 Pounds (261 kg) (approximate)
Cabinet Finish: Electrostatically applied thermosetting polyester.
Cylinder: 37" x 36" (94 x 91.4 cm) perforated galvanized steel with four baffles;
75 pounds (34.1 kg) dry weight (cotton load)
Motor: 3/4 H.P., lifetime lubricated, internal overload protected. See below for
reversing models.
Element: 30,000 watts (all models)
Max. Air Flow: (C.F.M.) 750 C.F.M. (354 liters/sec.)
Net Weight: 555 Pounds (252 kg) (approximate)