Alliance Laundry Systems UWH045K1L User manual

Programming
Washer-Extractor
Refer to Page 7 for Model Numbers
PHM1568R_SVG
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com F8552201R2
March 2017

WARNING
Machine installations must comply with minimum
specifications and requirements stated in the appli-
cable Installation Manual, any applicable municipal
building codes, water supply requirements, electrical
wiring regulations and any other relevant statutory
regulations. Due to varied requirements and applica-
ble local codes, this machine must be installed, ad-
justed, and serviced by qualified maintenance per-
sonnel familiar with applicable local codes and the
construction and operation of this type of machinery.
They must also be familiar with the potential hazards
involved. Failure to observe this warning may result
in personal injury, property damage, and/or equip-
ment damage, and will void the warranty.
W820
NOTE: The WARNINGS and IMPORTANT SAFETY IN-
STRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution, and care must be exer-
cised when installing, maintaining, or operating the
machine.
Any problems or conditions not understood should be reported to
the dealer, distributor, service agent or the manufacturer.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 F8552201R2

Table of Contents
Model Identification............................................................................... 7
Introduction........................................................................................... 8
Serial Plate Location....................................................................................... 8
Replacement Parts ......................................................................................... 8
Customer Service............................................................................................8
Preliminary Information.........................................................................9
About the Control........................................................................................... 9
Glossary of Terms...........................................................................................9
Power Failure Recovery.................................................................................. 9
Communications.............................................................................................9
Control Identification........................................................................... 10
Select Cycle Keypads....................................................................................10
Display Identification............................................................................11
Light Emitting Diodes (LEDs)........................................................................11
7-Segment Digits.......................................................................................... 11
Machine Operation...............................................................................12
Start Up....................................................................................................... 12
Door Locking Mode......................................................................................12
Stop Mode....................................................................................................12
Start Mode................................................................................................... 12
End of Cycle Mode....................................................................................... 12
Cycle Sequence............................................................................................ 12
Run Mode.................................................................................................... 12
Signals.........................................................................................................12
Special Features....................................................................................13
Programming the Control.............................................................................. 13
Collecting Audit Information......................................................................... 13
Testing Machine and Control Functions.......................................................... 13
Rapid Advance Feature................................................................................. 13
Communications Mode..................................................................................13
Entering the Manual Mode................................................................... 14
© Copyright 2017, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 F8552201R2

How to Enter the Manual Mode......................................................................14
How to Exit Programming Feature................................................................. 14
Programming Control...........................................................................15
What Can Be Programmed?........................................................................... 15
Programmable Options Available................................................................... 15
Programming Flowcharts...............................................................................19
Default Cycle dCYC..................................................................................... 24
Audio Signal AUd........................................................................................ 25
Error Code Programming Err-........................................................................ 27
Cycle Programming Cy--...............................................................................33
Number of Balance Retries bALr................................................................... 36
IR Access (Enable/Disable) IrA......................................................................36
Fahrenheit/Celsius t FC................................................................................. 38
Hot Water Temperature FH............................................................................ 39
Warm Water Temperature FHC...................................................................... 39
Cold Water Temperature FC...........................................................................40
Cooldown Enable/Temperature Codn .............................................................40
Production Test Cycle (Enable/Disable) PtEn.................................................. 41
Manual Rapid Advance (Enable/Disable) rAEn............................................... 41
No Cycle Time Display nCtd......................................................................... 42
Programmable Cycle Time Display PCtd........................................................ 42
Slow Drain Detection Adjust Value SdAd....................................................... 43
Set Real-Time Clock rtC-...............................................................................44
Manual Diagnostics (Enable/Disable) dAEn.................................................... 45
Low Water Level FLo (45/65 Pound Models).................................................. 45
Medium Water Level FnEd (45/65 Pound Models)...........................................46
High Water Level FHI (45/65 Pound Models)..................................................46
Temperature Controlled Fill Enable/Disable tCF (45/65 Pound Models).............47
Auto-Water Leak Detection ALd- (45/65 Pound Models)..................................48
Collecting Audit Information................................................................ 49
How to Enter Audit Feature........................................................................... 49
How to Read Audit Data................................................................................49
How to Exit Audit Feature............................................................................. 49
Manual Reset........................................................................................50
How to Enter Manual Reset........................................................................... 50
Testing Machine and Electronic Control Functions............................... 51
How to Enter Diagnostic Testing Feature........................................................ 51
How to Start Tests.........................................................................................51
How to Exit Diagnostic Testing Feature.......................................................... 51
Diagnostic Test Descriptions..........................................................................53
Error Codes..........................................................................................58
Rapid Advance Feature.........................................................................61
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 F8552201R2

How to Use Rapid Advance........................................................................... 61
How to Exit Rapid Advance Feature............................................................... 61
Communications Mode......................................................................... 62
Infra-red Communications............................................................................. 62
Default Cycles.......................................................................................63
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 F8552201R2

Model Identification
Information in this manual is applicable to these models:
Models
45 Pound [20.4
Kg]
UWH045K1L
UWH045K1M
UWH045K2L
UWH045K2M
UWL045K1L
UWL045K1M
UWL045K2L
UWL045K2M
UWN045K1L
UWN045K1M
UWN045K2L
UWN045K2M
UWU045K1L
UWU045K1M
UWU045K2L
UWU045K2M
65 Pound [29.5
Kg]
UWH065K1L
UWH065K1M
UWH065K2L
UWH065K2M
UWL065K1L
UWL065K1M
UWL065K2L
UWL065K2M
UWN065K1L
UWN065K1M
UWN065K2L
UWN065K2M
UWU065K1L
UWU065K1M
UWU065K2L
UWU065K2M
85 Pound [38.6
Kg]
UWH085K1M
UWH085K2M
UWL085K1M
UWL085K2M
UWN085K1M
UWN085K2M
UWU085K1M UWU085K2M
105 Pound [47.6
Kg]
UWH105K21
UWH105K2M
UWL105K1M
UWL105K2M
UWN105K1M
UWN105K2M
UWU105K1M UWU105K2M
130 Pound [59
Kg]
UWH130K1M
UWH130K2M
UWL130K1M
UWL130K2M
UWN130K1M
UWN130K2M
UWU130K1M UWU130K2M
Model Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 F8552201R2

Introduction
Serial Plate Location
Always provide the machine’s serial number and model number
when ordering parts or when seeking technical assistance. Refer
to Figure 1 .
Model Example of Serial Plate Location
PHM3254P_SVG
2
1
2
1. In control (UniLinc Models)
2. On front and back of machine
Figure 1
Replacement Parts
If literature or replacement parts are required, contact the source
from which the machine was purchased or contact Alliance Laun-
dry Systems at [phone] for the name and address of
the nearest authorized parts distributor.
Customer Service
For technical assistance, contact your local distributor or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: [phone] Ripon, Wisconsin
Introduction
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 F8552201R2

Preliminary Information
About the Control
This control is an advanced, programmable computer that lets the
owner control most machine features by pressing a sequence of
keypads. Refer to Figure 2 .
The control allows the owner to program custom cycles, retrieve
audit information, run diagnostic tests, and other programmable
features. Refer to Programming the Control for a list of features.
Machines shipped from the factory have a default cycle built in.
However, the owner can change the default cycle, or any cycle, as
needs permit.
The default cycle is #5.
IMPORTANT: In the event of a power failure, the control
will not have to be reprogrammed. It is designed with a
memory system that will remember how it was pro-
grammed until the electrical power is restored.
IMPORTANT: It is extremely important that the machine
has a positive ground and that all mechanical and elec-
trical connections are made before applying power to
or operating the machine.
Glossary of Terms
The following are a few terms and abbreviations to learn. These
are referred to throughout the instructions.
Display – This term refers to the window area of the control that
displays words and values.
LED (Light Emitting Diode) – This term refers to the lights next
to the keypads and status words of the control.
Power Failure Recovery
If a cycle is in progress and the power fails for less than five (5)
seconds, the cycle status is saved in memory. When the power re-
covers, the machine will resume into the previously active cycle.
If the length of the power failure is greater than five seconds, the
control will end the cycle and the display will revert back to Start
Mode.
Communications
The control may be programmed manually or by infra-red com-
munication with an external device.
IR Communications
An external device, such as a PDA, allows the owner to program
and retrieve information from the control without touching the
keypad. An external device greatly expands the programming op-
tions available to the owner. However, it is not required to pro-
gram and operate the machine. The operation of an external de-
vice and the advanced features available are covered separately in
the instructions included with the external device software. Con-
tact Alliance Laundry Systems for a list of approved PDAs and
other external devices.
Preliminary Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 F8552201R2

Control Identification
Select Cycle Keypads
(Refer to Figure 2 )
Select Cycle keypads are used to select the specific machine cy-
cle. These pads are numbered 0-9 and allow the user to select a
cycle other than the default cycle (#5). The Select Cycle keypads
are not active after starting a cycle. Pressing the flashing START
(enter) keypad will confirm the selection and the cycle will begin.
The Select Cycle keypads are used in various combinations for
programming cycles, retrieving audit information, running diag-
nostic tests, and other operations. These instructions cover the
manual programming and data retrieval options.
PHM1568R_SVG1
11
10
9
8
76
5
4
3
2
1
1. Select Cycle keypads
2. Display
3. Four 7-Segment Digits
4. STOP UNLOCK keypad
5. START (enter) keypad
6. START (enter) LED Light
7. LED Status Lights
8. Wash
9. Rinse
10. Spin
11. Door
Figure 2
Control Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 F8552201R2

Display Identification
Light Emitting Diodes (LEDs)
(Refer to Figure 2 )
Light Emitting Diodes (LEDs) are used to indicate the chosen cy-
cle, cycle status, when the bleach compartment is dispensing, and
door lock information. See below for information on each LED.
START LED
Strat LED is lit once the START (enter) keypad has been pressed.
WASH LED
Wash LED is lit at the beginning of a wash portion of the cycle
and will remain lit until the wash is complete.
RINSE LED
Rinse LED is lit at the beginning of a rinse portion of the cycle
and will remain lit until the rinse is complete.
SPIN LED
Spin LED is lit during the final spin portion of the cycle.
DOOR LED
Door LED is lit whenever the door is locked. The door can’t be
opened when this LED is lit.
7-Segment Digits
The 7-Segment Digits are used to display the time remaining in a
cycle, error messages and descriptive codes. During diagnostic
testing or manual programming of the control, these digits will
display descriptive codes and values (as described in Entering the
Manual Mode).
Display Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11 F8552201R2

Machine Operation
Start Up
When power is applied to the machine, the control becomes ac-
tive and will display its software version as SXX (XX is the ver-
sion number) for one (1) second. If the control was not powered
down during a running cycle, it will enter the Start Mode.
Door Locking Mode
The control enters this mode after the START (enter) keypad is
pressed in Start Mode. The control stays in Door Locking Mode
until it confirms the door is closed and locked.
Stop Mode
The control enters this mode if the user stops the cycle by press-
ing the STOP UNLOCK keypad. If control does not detect water
or cylinder rotation it will enter End Of Cycle Mode.
Start Mode
The control enters this mode when machine is ready for opera-
tion. The display will show CYxx where xx is the cycle num-
ber.
After pressing the START (enter) keypad, with the door closed
and locked, the cycle will begin. The cycle cannot be changed
once the cycle has started.
End of Cycle Mode
When a cycle is complete, the control will display 00 until the
machine door is opened. When this event occurs the display will
revert back to Start Mode.
Cycle Sequence
Upon the start of a cycle, the control will display the total cycle
time. The appropriate LEDs will light while the machine passes
through different cycle steps. Any coin entered after the first fill
step will be added to the total coin counter, but the user will not
be able to change cycles.
Run Mode
The control enters this mode when a cycle is running. The time
remaining appears in the display, the status LEDs are lit and the
loading door is locked.
Signals
The options for when a signal can be used during the machine op-
eration are listed below:
1. End of Cycle Signal - By default, this signal is turned off. If
turned on, the signal sounds for three (3) seconds at the end of
a cycle.
2. Signal On Keypad Depression - By default, this signal is
turned on and sounds for a quarter of a second each time a
keypad is pressed.
NOTE: Refer to Programming the Control to program sig-
nal options.
Machine Operation
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 F8552201R2

Special Features
Programming the Control
The control allows the machine owner to program the control
with the use of the keypad. Cycle options may be programmed,
audit information may be viewed and diagnostic tests may be run
by pressing combinations of the keypads.
For details on programming select cycle options, refer to Pro-
gramming Control.
Collecting Audit Information
The control will store audit information in its memory that can be
retrieved by pressing various combinations of Select Cycle key-
pads. The control will record total machine cycles.
For more information on the audit features, refer to Collecting
Audit Information.
NOTE: Additional audit information is retrievable with
an external device, using infra-red communications.
Refer to the appropriate instruction manual.
Testing Machine and Control Functions
Special diagnostic features built into the control allow the owner
to run specific diagnostic tests. By opening and closing the top
cover and then pressing various sequences of Select Cycle key-
pads, the owner may retrieve or perform the following tests:
• Front End Control Software Version Number
• Output Board Control Software Version Number
• Output Board Water Level Sensor Trim Value
• Top Cover Opening Test
• Door Switch Input Test
• Door Lock Input Test
• Show Fill Time Test
• Show Drain Time Test
• Temperature Sensor Display Test
• Start Pulse Test (45 and 65 pound models)
• VFD Balance Input Test
• 24 VAC Switch Input Test
• VFD Drive Fault Input Test
• Frame Stability Switch Input Test
• VFD Balance Weight Test
• Drive DC Bus Display Test (45 and 65 pound models)
• Water Purge Test
• Water Leak Detection Test
• Drive Software Version Number (45 and 65 pound models)
• Drive Parameter Table Version Number (45 and 65 pound
models)
• Drive Type (45 and 65 pound models)
For detailed information on running diagnostic tests, refer to Test-
ing Machine and Electronic Control Functions.
Rapid Advance Feature
This feature allows the user to quickly advance through active cy-
cles. This feature is useful when tests must be performed immedi-
ately on a machine currently in an active cycle. In this case, the
user can quickly advance through the cycles to shakeout. At this
point, the user can perform the required tests and then return the
machine to the point it was interrupted.
Communications Mode
This feature allows the control to communicate with an external
device. This allows the control to be programmed and have its
data read without using the keypad.
For more detailed information on using the Communications
Mode feature, refer to Communications.
Special Features
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 F8552201R2

Entering the Manual Mode
For programming, testing, and retrieving information from the
control, it is often necessary to enter the Manual Mode by follow-
ing the six (6) simple steps below.
For an overview the Manual Mode, refer to Entering Manual
Mode.
How to Enter the Manual Mode
1. If the machine is in an active cycle, rapid advance through the
cycle. Refer to the Rapid Advance Feature.
2. While pressing and holding the #4 keypad with one hand,
press the #1 keypad with the other hand.
3. The display will show rAPd.
4. Press the #3 (∧) or the #6 (∨) keypad to scroll through the op-
tions until the desired option appears in the display.
5. Press the START (enter) keypad.
Manual Mode is broken into three (3) groups: Manual Program-
ming, Manual Rapid Advance and Manual Diagnostics. Manual
Programming can only be turned on or off with an external de-
vice. Refer to the appropriate instruction manual. Manual Rapid
Advance and Manual Diagnostics can be turned on and off using
an external device or by manual programming (refer to Manual
Rapid Advance (Enable/Disable) rAEn and Manual Diagnostics
(Enable/Disable) dAEn of Programming Control).
By default, all groups are turned on.
The manual features available in each group are as follows (the
menu displayed on the display in this mode is in parentheses).
•Manual Programming
•Manual Programming (Prog)
•Manual Read Audit (AUdt)
•Manual Reset (rSEt)
•Manual Rapid Advance
•Rapid Advance (rAPd)
•Manual Diagnostics
•Manual Diagnostic Tests (diAg)
If a group is turned off, the display will change from the selected
feature to oFF when the START (enter) keypad is pressed and an
audio signal will sound for one (1) second. The display will then
return to the selected feature. The features in the group cannot be
entered.
How to Exit Programming Feature
Press the #5 (<) keypad until the control returns to Start Mode.
Entering the Manual Mode
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14 F8552201R2

Programming Control
What Can Be Programmed?
This feature allows the owner to program cycle parameters and
other features by using the keypads. The control must have the
Manual Programming Mode enabled, which is the factory de-
fault. This mode can only be turned oFF and on by using an ex-
ternal device. Refer to this section when programming the con-
trol.
This section offers a detailed description of all available program-
mable options.
Each description includes instructions on when and why the op-
tion might be used and, more importantly, how to program the
option.
For an overview of the programming organization, refer to the
flowcharts on the following pages.
For more advanced users, see the quick reference list (refer to Ta-
ble 1) and programming flowcharts (refer to Programming Flow-
charts) for the options available through the programming mode.
NOTE: The codes in the Option Display column of Table
1 are displayed when that option is selected.
Programmable Options Available
Option
Number
Option Dis-
play Description Default Value Value Range
1dCYC Default Cycle Cy05* Cy01-Cy30*
2AUd Audio Signal 29* 0-31*
3Err- Errors — —
a. E FL Fill Errors on on/oFF
b. E dr Drain Error on on/oFF
c. E Ub Unbalance Error Display on on/oFF
d. E oP Open Thermister Error Dis-
play
on on/oFF
e. E SH Shorted Thermistor Error Dis-
play
on on/oFF
f. E Ht Heat Error Display (heater on-
ly)
on on/oFF
g. LE- (45/65
pound models)
LEr (85-160
pound models)
Water Leak Detection Error — —
1. LEr1 Water Leak Detection During
a Machine Cycle (on/off)
oFF on/oFF
2. LEr2 Water Leak Detection Day of
Week Enable
127* 0-127*
3. LEr3 Number of cycles between
leak detection test
0* 0-127*
h. E Sd Slow Drain Detection oFF on/oFF
Table 1 continues...
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15 F8552201R2

Option
Number
Option Dis-
play Description Default Value Value Range
4Cy-- Cycle Programming Refer to Default Cycles for default cycle information
a. AgIt Cycle Agitate — —
1. tyPE Agitate Type ** 1-4*
2. ASPd Agitate Speed ** Lo/rEg*
b. SEg- Cycle Segment Programming — 1-8*
1. SgEn Segment Enable/Disable ** on/oFF
2. FILL Fill Step — —
a. FLEn Fill Step Enable/Disable ** on/oFF
b. FLEU Fill Level ** HI/nEd/Lo or 1-30
c. tEnP Fill Temperature ** CoLd/Uarn/Hot
35°F-194°F [2°C-90°C]
3. SUPL Supply Step — —
a. SUEn Supply Step Enable/Disable ** on/oFF
b. dISP Dispenser Options ** Display will show Sx
(i) S1 Supply #1 ** on/oFF
(ii) S2 Supply #2 ** on/oFF
(iii) S3 Supply #3 ** on/oFF
(iv) S4 Supply #4 ** on/oFF
c. SdUr Supply Duration ** Press START (enter) keypad
to access options
(i) SEC Seconds ** 0-59
(ii) nIn Minutes ** 0-9
4. AgSt Agitate Step — —
a. AgEn Agitate Step Enable/Disable ** on/oFF
b. AdUr Agitate Duration (in minutes) ** 1-30 for agitate types 1 or 2
1-180 for agitate types 3 or 4
c. HEAt Heat in Agitate (if heater is
present)
** oFF/1/2**
5. drAn Drain Step — on/oFF
6. SPIn Spin Step — —
a. SPEn Extract Step Enable/Disable ** on/oFF
b. SSEC Extract Seconds ** 0-59
Table 1 continues...
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16 F8552201R2

Option
Number
Option Dis-
play Description Default Value Value Range
c. SnIn Extract Minutes ** Intermediate Extract:
Min. Step Time = 30 sec-
onds
Max. Step Time = 3:59 mi-
nutes
Final Extract:
Min. Step Time = 30 sec-
onds
Max. Step Time = 9:59 mi-
nutes
d. SSPd Extract Speed ** 1-3*
c. Cnin Cycle Time 0* 0-255 minutes
5bALr Number of Balance Retries 1 (45/65 pound models)
3 (85-160 pound models)
1-7
6IrA IR Access (enable/disable) on on/oFF
7t FC Fahrenheit/Celsius FAHr (Fahrenheit) FAHr/CEL
8FH Hot Water Temperature 140°F [60°C] 35°F-194°F [2°C-90°C]
9FHC Warm Water Temperature 100°F [38°C] 35°F-194°F [2°C-90°C]
10 FC Cold Water Temperature 35°F [2°C] 35°F-194°F [2°C-90°C]
11 Codn Cooldown Enable/Tempera-
ture
oFF oFF /
50°F-160°F [10°C-71°C]
12 PtEn Production Test Cycle (ena-
ble/disable)
on on/oFF
13 rAEn Manual Rapid Advance
(Enable/Disable)
on on/oFF
14 nCtd No Cycle Time Display oFF on/oFF
15 PCtd Programmable Cycle Time
Display
0 0 = Disabled
1 = Enabled
16 SdAd Slow Drain Detection Adjust 0 0-255 seconds
17 rtC- Real Time Clock — —
a. rtC1 Set Real Time Clock Minutes — 00-59
b. rtC2 Set Real Time Clock Hours — 00-23
c. rtC3 Set Real Time Clock Day — 001 (Sunday)-007 (Saturday)
Table 1 continues...
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17 F8552201R2

Option
Number
Option Dis-
play Description Default Value Value Range
d. rtC4 Set Real Time Clock Date — 1-31
e. rtC5 Set Real Time Clock Month — 1-12
f. rtC6 Set Real Time Clock Year — 00 (2000)-99
g. rtC7 Daylight Saving Option on on/oFF
18 dAEn Manual Diagnostics (enable/
disable)
on on/oFF
19 FLo Low Water Level 3 1-10
20 FnEd Medium Water Level 15 11-20
21 FHI High Water Level 27 21-30
22 tCF Temperature Controlled Fill oFF on/oFF
23 ALd- Auto-Water Leak Detection — —
a. ALd1 Auto-Water Leak Detection
(on/off and cycles)
oFF oFF/0-127 (Cycles)
b. ALd2 Auto-Water Leak Detection
Hour
0 0-23
c. ALd3 Auto-Water Leak Detection
Day of Week
127* 0-127*
*Refer to programming section for value definition.
**Refer to the Default Cycles for default cycle setting information.
Table 1
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18 F8552201R2

Programming Flowcharts
Entering Manual Mode
Enter Manual Mode.
Press and hold both #4 keypad and
#1 keypad at the same time.
“rAPd” - Quickly advance through active
cycles.
1. Press START (enter) keypad to begin Rapid
Advance cycle and advance through cycle
steps.
“AUdt” - Retrieve audit information for
machine.
1. Press START (enter) keypad.
“CyC” - Total number of machine cycles:
1. Press START (enter) once to read audit.
“rSEt” - Reset the control’s programming data
to factory default.
1. Press START (enter) keypad.
“Prog” - Program cycle information and other
features into the control.
1. Refer to the Manual Programming flowchart.
“dIAg” - Run diagnostic tests on machine
operations.
1. Press START (enter) keypad. Refer to
Diagnostic Tests flowchart.
“rCyC” - Total number of rapid advance cycles:
1. Press START (enter) once to read audit.
PHM1563R_SVG
Figure 3
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19 F8552201R2

Manual Programming
PHM1564R_SVG
“AUd” - Program when the signal will sound.
“Err-” - Turn on/off certain errors in control.
“E dr” - Drain Error
“E Ub” - Unbalance Error
“E Sd” - Slow Drain Detection
“FILL” - Program fill step options
“LEr-” - Leak Detection
“E oP” - Open Thermistor Error
“E SH” - Shorted Thermistor Error
“LEr1” - Water Leak Detection During
a Machine Cycle
“LEr2” - Water Leak Detection - Day
of Week
“LEr3” - Number of Cycles Between Water
Leak Detection During a Machine Cycle
“0” - “127”
“dCYC” - Set the default cycle and
temperature.
“Cy--” - Program aspects for the various
steps in each type of cycle. There are (30)
cycles available for programming.
(continued) (continued)
“SEg1” - Program options for each
segment. There are (8) segments
available for programming
“SgEn” - Segment Enabled/Disabled:
“on” = Enabled
“oFF” = Disabled
“tyPE” - Agitation Type:
1 = 18/3/18
2 = 10/20/10
3 = 3/27/3
4 = 4/56/4
“ASPd” - Agitation Speed:
“Lo” = Reduced Speed
“rEg” = Normal Speed
“AgIt” - Program the cycles agitation
action and speed
(continued)
““FLEn” - Fill Step Enable/Disable:
“on” = Enabled
“oFF” = Disabled
“FLEU” - Fill Level:
“HI” = High Level
“nEd” = Medium Level
“Lo” = Low Level
“1-30” = Fill Level
“tEnP” - Fill Temperature:
“CoLd” = Cold
“UArn” = Warm
“Hot” = Hot
(35°F - 194°F [2°C - 90°C])
“E Ht” - Heat Error (heater only)
“E FL” - Fill Error
Figure 4
Programming Control
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20 F8552201R2