Allied Telesis AT-MC13 User manual

Datasheet | Media Converters
AT-MC13
UTP to fiber ST Ethernet media converter
AT-MC14
UTP to fiber SC Ethernet media converter
AT-MC15
UTP to BNC Ethernet media converter
AT-MC16
UTP to fiber ST single-mode Ethernet media
converter
Fiber Connections
The Allied Telesis range of Ethernet media
converters provides a complete family of
conversion devices, allowing users to extend the
size of UTP networks with the use of fiber
cabling. Supporting all major fiber connectors,
with support for both multi and single-mode
fiber, these converters can be used to extend
networks with up to 15km of fiber.
Auto-Negotiation and MissingLink™
When connecting media converters to auto-
negotiating Fast Ethernet switches, these media
converters (except the AT-MC13 and AT-MC14)
will automatically connect the link in either
Ethernet full or half-duplex mode, allowing the
link to be established with the greatest
bandwidth. In addition, the MissingLinkTM feature
(except AT-MC15) allows switches or hubs with
redundant link capability to be inter-connected
with these media converters, as a failure in one
fiber link will be signalled to the switch, allowing
the second link to become active.
Simple Installation
All the media converters with a UTP
connection feature an internal MDI/MDI-X
switch, allowing the converter to be connected
to either a PC, hub or switch, with a simple UTP
cable.The media converters also allow the
installer to test the integrity of the fiber
connection, byforcing the converters to
communicate over the fiber cable.This ‘Link Test’
feature allows installers to check for cable faults
without the need for expensive fiber optic test
equipment.
Standalone or Rack-mounted
Each small media converter is powered by an
external power supply unit for use in standalone
applications. Where multiple media converters
are being used, up to 12 standalone devices can
be inserted into a low-cost rack-mount chassis,
allowing all the converters to be powered by a
single internal power supply. In critical
applications, a second load sharing internal
power supply can be installed into the rack-
mount chassis.
Key Features
•Half and full-duplex operation
(excluding AT-MC15, half-duplex only)
•Rack-mountable using optional AT-MCR12,
AT-TRAY4 or AT-TRAY1 chassis
•MDI/MDI-X
•MissingLink™ (excluding AT-MC15, N/A)
•Link Test (excluding AT-MC15, N/A)
MC1x Series
Ethernet Media Converters
Allied T
elesis www.alliedtelesis.com

Technical Specifications
Status Indicators
Front Panel
Power (PWR) Indicates power is applied to the
converter
Link (LNK) (2) Indicates a valid receive link
exists
Receive (REC) (2) Indicates valid data being
received by converter
Normal (NML) Indicates product is working in
normal mode
On Line Indicates BNC port is connected
to an active 10Base2 segment
(AT-MC15 only)
Collision (COL) Indicates BNC port is sensing a
collision signal (AT-MC15 only)
Packet Transmission Characteristics
Round Trip Delay 0.4µs Maximum
Bit Error Rate (BER) <10-12
Twisted Pair Interface
Transmitter Typical Worst
Peak Differential
Signal Amplitude 2.5v 2.2 to 2.8v
Transmitter Jitter ±3.2ns
Harmonics Content 27dB below fund
Common Mode 4v
Output Voltage:
Silence 0v +50mv
Link Test Pulse 130ns 105 to 135ns
Output Impendance 100
Ω 85 to 115 Ω
UTP Length 100m
Receiver:
Receiver Threshold -400mv -300 to 585mv
Differential Noise 300mv
Power Characteristics
External Power Supply 100-240V AC, 50/60Hz +/-3%
Input Supply Voltage 12vDC +/-5%
Max Current .5
Power Consumption 6W
Environmental Specifications
External Power Supply 120V AC, 60Hz (US model)
240V AC, 50Hz (European models)
Input Supply Voltage 12vDC
Max Current 500mA
Power Consumption 6W
Physical Characteristics
Dimensions 10.5cm x 9.5cm x 2.5cm
(W x D x H) (4.12” x 3.75” x 1.0”)
Weight 294g (10.4oz)
Electrical/Mechanical Approvals
EMC FCC Class A
Safety UL-Cul, CSA/CSA, NRTL, TUV,
CE compliant
Ordering Information
AT-MC13-xx
UTP to fiber Media Converter with ST fiber connectors
AT-MC14-xx
UTP to fiber Media Converter with SC fiber connectors
AT-MC15-xx
UTP to BNC Media Converter
AT-MC16-xx
UTP to fiber Media Converter with ST single-mode fiber
connectors
Where xx = 10 AC Power supply, US power cord
20 AC Power supply, European power cord
30 AC Power supply, UK power cord
40 AC Power supply, Australian power cord
MC1x Series |Ethernet Media Converters
USA Headquarters |19800 North Creek Parkway |Suite 200 |Bothell |WA 98011 |USA |T: [phone] |F: [phone]
European Headquarters |Via Motta 24 |6830 Chiasso |Switzerland |T: +41 91 69769.00 |F: +41 91 69769.11
Asia-Pacific Headquarters |11 T
ai Seng Link |Singapore |534182 |T: [phone] |F: [phone]
www.alliedtelesis.com
©2007 Allied T
elesis Inc.All rights reserved. Information in this document is subject to change without notice. All company names, logos, and product designs that are trademarks or registered trademarks are the property of their respective owners. 617-00274-00 Rev F