Allied Telesis AT-8624T/2M, AT-8624PoE Installation and operating manual

A5 Quick Install Guide Cover
AT-8600 Series Switch
Installation and Safety Guide
AT-8624T/2M
AT-8624PoE
613-000051 REV A

2 AT-8600 Series Switch
AT-8600 Installation & Safety Guide
Document Number C613-000083 REV B.
Copyright © 2005 Allied Telesyn Inc, Corp.
19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA.
All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesyn.
Allied Telesyn International, Corp. reserves the right to make changes in
specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without
notice. In no event shall Allied Telesyn be liable for any incidental, special,
indirect, or consequential damages whatsoever, including but not limited to lost
profits, arising out of or related to this manual or the information contained
herein, even if Allied Telesyn has been advised of, known, or should have known,
the possibility of such damages.
All company names, logos, and product designs that are trademarks or
registered trademarks are the property of their respective owners.
8600isg.fm Page 2 Wednesday, June 22, 2005 2:46 PM

Installation & Safety Guide 3
Electrical Safety and Emission Compliance Statement
STANDARDS: This product meets the following standards:
Category Approval Agency and Requirement
UL60950-1
CAN/CSA-C22.2 No. 60950-1-03
EN60950-1
EN60825
Electromagnetic Compliance FCC CFR47 Part 15 Class A
EN55022 Class A
VCCI Class A
AS/NZS CISPR22 Class A
Immunity EN55024
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
8600isg.fm Page 3 Wednesday, June 22, 2005 2:46 PM

4 AT-8600 Series Switch
Electrical Safety
IMPORTANT: This equipment must be installed in accordance with safety
precautions (page 18, 1).
Elektrische Sicherheit
WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von
Sicherheitsvorkehrungen erforderlich (Seite 19, 2).
Elektrisk sikkerhed
VIGTIGT: Dette udstyr skal installeres i overensstemmelse med
sikkerhedsadvarslerne (side 22, 3).
Elektrische veiligheid
BELANGRIJK: Dit apparaat moet in overeenstemming met de
veiligheidsvoorschriften worden geïnstalleerd (pagina 24, 4).
Sécurité électrique
IMPORTANT: Cet équipement doit être utilisé conformément aux instructions
de sécurité (page 26, 5).
Sähköturvallisuus
TÄRKEÄÄ: Tämä laite on asennettava turvaohjeiden mukaisesti (sivu 28, 6).
Sicurezza elettrica
IMPORTANTE: questa apparecchiatura deve essere installata rispettando le
norme di sicurezza (pagina 30, 7).
Elektrisk sikkerhet
VIKTIG: Dette utstyret skal installeres i samsvar med sikkerhetsregler
(side 32, 8).
Segurança eléctrica
IMPORTANTE: Este equipamento tem que ser instalado segundo as medidas de
precaução de segurança (página 34, 9).
Seguridad eléctrica
IMPORTANTE: La instalación de este equipo deberá llevarse a cabo cumpliendo
con las precauciones de seguridad (página 36, 10).
Elsäkerhet
OBS! Alla nödvändiga försiktighetsåtgärder måste vidtas när denna utrustning
används (sida 38, 11 ).
EC Declaration of Conformity
EC Declaration of Conformity (page 40).
8600isg.fm Page 4 Wednesday, June 22, 2005 2:46 PM

Installation & Safety Guide 5
Table of Contents
Electrical Safety and Emission Compliance Statement ............................................. 3
Models Covered By This Guide .................................................................................... 6
Package Contents ............................................................................................................. 6
Selecting a Site ................................................................................................................... 7
How to Install the Switch ............................................................................................... 8
How to Configure the Switch ..................................................................................... 11
LEDs on AT-8600 Series Switches .............................................................................. 14
Documentation and Tools CD-ROM ......................................................................... 17
Translated Safety Statements ....................................................................................... 18
EC Declaration of Conformity .................................................................................... 40
8600isg.fm Page 5 Wednesday, June 22, 2005 2:46 PM

6 AT-8600 Series Switch
Models Covered By This Guide
This Installation & Safety Guide includes information on these models:
■AT-8624T/2M 24-port 10BASE-T/100BASE-TX Layer 3 Ethernet Switch
■AT-8624PoE Layer 3 Fast Ethernet Switch
You can download Installation & Safety Guide updates from
http:// www.alliedtelesyn.com/support.
Package Contents
These items are included with each AT-8600 Series switch:
■One AC power cord
■One power cord retaining clip
■One serial cable for connecting the switch to a terminal or PC
■One 19 inch rack-mount kit
■One AT-8600 Series Installation & Safety Guide (which includes statutory and
safety information)
■One AT-8600 Series Documentation and Tools CD-ROM (which includes
the complete AT-8600 Series document set and utilities)
■One warranty card
Contact your authorised distributor or reseller if any items are damaged or
missing.
8600isg.fm Page 6 Wednesday, June 22, 2005 2:46 PM

Installation & Safety Guide 7
Selecting a Site
You can install the switch in a standard 19-inch rack, on a level surface such as a
desktop or bench, or against a wall using the optional wall-mount kit. How to
install the switch using the 19-inch rack-mount kit is described below. How to
install the switch using the wall-mount kit is described in the AT-8600 Series
Hardware Reference.
When you install the switch, choose a site that:
■allows adequate airflow around the switch and its vents.
■is free of dust and moisture.
■will maintain an ambient temperature range of 0 º C to 40º C
(32º F to 104º F) and a humidity range of 5% to 80% non-condensing.
■has a reliable and earthed (grounded) power supply, preferably dedicated
and filtered.
■does not expose cabling to sources of electrical noise such as radio
transmitters, broadband amplifiers, power lines, electric motors, and
fluorescent fixtures.
■allows easy access to the switch’s power and cable connections.
■allows all related network devices to be connected to the switch without
exceeding maximum cable length limitations as specified in the AT-8600
Series Hardware Reference.
■ensures that when the switch is mounted in a rack, the switch is mounted
evenly to prevent uneven mechanical loading of the rack.
8600isg.fm Page 7 Wednesday, June 22, 2005 2:46 PM

8 AT-8600 Series Switch
How to Install the Switch
Warning All versions of this equipment must be earthed.
Prepare to install the switch
1. Read the safety information
Read the safety information included in this Installation & Safety Guide. This
Installation & Safety Guide is also on the Documentation and Tools CD-ROM
and you can download a copy from http:// www.alliedtelesyn.com.
2. Gather the tools and equipment you will need
You will need a Phillips #2 screwdriver and cage nuts to attach the brackets
to your rack. Cage nuts are not supplied.
3. Choose a suitable operating location
Follow the guidelines described in “Selecting a Site” on page 7 to choose a
suitable location.
You can install the switch either in a 19-inch rack, on a flat bench, or against
a wall.
4. Unpack the switch
Verify the package contents. If any items are damaged or missing, contact
your authorised distributor or reseller.
5. Install expansion modules (optional)
The only expansion module supported by the AT-8624T/2M is the AT-A46.
If you purchased expansion modules, install them now by following the
instructions in the AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules
Installation Guide that comes with the modules. The AT-A46 expansion
module is supported by AT-8000 Series switches as well as AT-8600 Series
switches.
Hot swap of expansion modules is not supported on AT-8624T/2M
switches. If you insert or remove a module when the switch is already
powered on, you must restart the switch before the module can be used.
8600isg.fm Page 8 Wednesday, June 22, 2005 2:46 PM

Installation & Safety Guide 9
6. Place the switch in its operating location
If installing the switch in a rack:
• Remove the rubber feet on the bottom of the switch with a flat-head
screwdriver.
• Attach the two rack-mounting brackets to the switch with the screws
provided.
• Mount the switch in the rack using standard screws (these are not
provided).
7. Check the supply voltage and the switch’s rated voltage
AT-8600 Series switches are fitted with a universal main power supply that
will function over the range 100–240 VAC and 50–60 Hz.
The specific power supply requirements for a particular model are clearly
displayed on the rear or underside of the switch. If the supply is outside the
accepted range for the switch, the switch may not operate or damage to
the switch may result.
8. Apply AC power to the switch
Plug the power cord into the AC power connector on the switch’s rear
panel as shown in Figure 1. The Fault LED should flash for approximately 10
seconds as the switch runs internal tests. If the LED continues to flash,
refer to the AT-8600 Series Hardware Reference for troubleshooting
information.
Figure 1: AT-8624T/2M front and rear panel with AC power inlet.
Figure 2: AT-8624PoE front and rear panel with AC power inlet
1 3 5 7 9 11 13 15 17 19 21 23
2 4 6 8 10 12 14 16 18 20 22 24
LINK
MODE
LINK
MODE
FAULT
RPS
MASTER
PWR
MODE
1357911
24681012
13 15 17 19 21 23
14 16 18 20 22 24
STATUS
RS-232
TERMINAL PORT
26
COL
100
FULL
ACT
AT-8624T/2M Advanced Fast Ethernet Switch
25
25
1 3 5 7 9 11 13 15 17 19 21 23
2 4 6 8 10 12 14 16 18 20 22 24
FAULT
RPS
MASTER
PWR
MODE
1357911
24681012
13 15 17 19 21 23
14 16 18 20 22 24
STATUS
26
RS-232
TERMINAL PORT
COL HALF DUP FULL DUP
ACT100 LINK 10 LINK ACT
PD ON MAX CURRENTPD ERR
AT-8624POE Layer 3 Fast Ethernet Switch
8600isg.fm Page 9 Wednesday, June 22, 2005 2:46 PM

10 AT-8600 Series Switch
9. Check that the PWR LED on the switch’s front panel lights green
If the PWR (power) LED fails to light, refer to the AT-8600 Series Hardware
Reference for troubleshooting information.
10. Connect the data cables
Make sure each cable connection is secure. The switch will now perform
basic Layer 2 switching functions.
8600isg.fm Page 10 Wednesday, June 22, 2005 2:46 PM