Almost Heaven Saunas Logan Operating instructions

®
Logan Sauna
Installation & Owner’s Manual
In addition to reading this manual through to the end before proceeding with assembly
you may nd our instruction video helpful.
You can nd it at: youtube.com/user/almostheavensauna

®
Thank you for your purchase of your Logan sauna! Should you have any questions during assembly, please feel
free to call us at 888.355.3050, or email [e-mail].
Regular business hours are 9-5 EST, M-F.
Your Logan Indoor Sauna is specically designed to utilize your existing oor. As such, assembly is made very
simple since the entire sauna sits on pre-fabricated rails and risers. Your sauna can be assembled on any surface
that is rm and at, including concrete, ceramic, vinyl, laminate or tile. Installation on a carpeted surface is not
recommended.
Your Logan kit should include the following:
c 4 oor risers
c 4 Wall support rails
c 4 Roof support rails
c 2 Roof panels
c 2 Pieces of roof trim
c Wall panel A
c Wall panel B
c Wall panel C
c Door panel D
c Window panel E
c Wall panel F
c Bench
c Backrest w/LED light
c LED power supply
c Door handle assembly
c Heater
c Stones
c Wall sensor cover
c Hardware bag containing 2”screws, 2.5”bench screws, and trim nails
c Heater fence kit
These tools are required to assemble yourLogan sauna:
c Cordless drill
c Tape measure
c Rubber mallet
c Hammer
c 1/2” or 5/8” Forstner bit
c Utility knife
c Screwdriver (phillips and athead)
c Level
c Step stool or ladder
c Framing square
Read this entire manual through to the end before proceeding with the assembly.
LOGAN INSTALLATION MANUAL
page 1

LOGAN INSTALLATION MANUAL
page 2
Step 1. Connect the Four Floor Risers
Fasten the four oor risers together using the predrilled holes as a guide. (1-2)
Step 2. Position Wall Support Rails
Align each wall support so that the angled cuts make a corner. Each wall support has a predrilled hole. Fasten the
front, back, and sides together (3 & 4) and lay the assembly squarely on top of the oor risers with the groove facing
up (5). The rails should overlap both sides of the riser by approximately 1” (6). Secure the assembly to the oor risers
using three screws evenly spaced on each wall support rail (7 & 8).
Step 3. Position wall panels A & B
Position wall panel A in the groove of the left rail and push it ush against the back rail. Having a helper hold wall
panel A, placewall panel B in the groove of the back rail (9 & 10). Push the at edge against wall panel A. Align the two
panels so they are ush and fasten them together using the 2”screws through the predrilled holes (11).
Image 1 Image 2
Image 3 Image 4 Image 5
Image 6 Image 7 Image 8
Image 9 Image 10 Image 11
AB

LOGAN INSTALLATION MANUAL
page 3
Step 4. Position Wall Panel C
Position wall panel C into the groove of the back rail. Attach it to wall panel B by way of the tongue and groove t (12
& 13). Secure it by tapping it into place with a rubber mallet.
Step 5. Position Door Panel D
Position door panel D onto the front rail, being sure to snip the twine holding the door to the frame (14). Push door
panel D into place against wall panel A (15). Being sure the two panels are ush, fasten them together using 2” screws
through the predrilled holes on panel A.
Step 6. Position Window Panel E
Window panel E will connect to door panel D via tongue and groove t (16 & 17).
Step 7. Position Wall Panel F
Place wall panel F in the right-side rail. Fasten through predrilled holes into wall panel C and window panel E (18 &19).
B C
Image 12 Image 13
A
D
Image 14 Image 15
Image 16 Image 17
F C E
Image 18 Image 19

LOGAN INSTALLATION MANUAL
page 4
Step 8. Bench and LED Backrest Installation
Note: You may choose to install all the benches and backrests after the sauna is completed, but you may nd it easier
to install with the extra space and light aorded at this step.
Mount the Bench on the pre-placed bench supports. Fasten it in place using the pre-drilled holes on the sides, top,
and bottom of the bench, rmly attaching it to the bench supports and to the wall of the sauna (20 & 21).
Measure the desired height at which you want to install the back rest (suggested: 8-12”above the bench, centered on
the wall). Use 2”screws and pre-drilled holes to attach the Back Rest to Wall Panel F (22).
The LED lighting comes installed on the back of the Back Rest. Find the cord coming from the light switch and bore a
5/8” hole in wall panel C to insert the light cord through so it comes through to the outside of the sauna (23-25).
Use provided screws to position Power Supply where it is most convenient for you on the outside of wall panel C (26).
Optional: Secure excess wire with zip tie or some other fastener as desired. Plug the cord into the power supply (27).
Plug the power supply into any wall outlet, and ip the switch mounted on the back of the bench to operate the LED
light.
Image 20 Image 21
Image 22
Image 23 Image 24 Image 25
Image 26 Image 27

LOGAN INSTALLATION MANUAL
page 5
Step 9. Assemble and Position Roof Support Rails
Align each roof support rail so the angled cuts join together to make a 90-degree angle placing the longer supports
on the sides and the shorter supports on the front and back. Fasten them together using 2” screws through the pre-
drilled holes (28 & 29). This is the same assembly you performed in Step 2.
Place the assembly on top of the wall panels so that the wall panels t snugly into the groove. When in place, secure
the assembly to the walls using three 2”screws on each rail (29 & 30).
Step 10. Position Roof Panels
Position the two roof panels on top of the roof support rails with the predrilled holes facing up (31-32). The roof
panels connect via tongue and groove t. Align the connected roof panels on the rails so that approximately 1” of the
support rails extend past each side of the roof panels. Once evenly spaced, secure the panels with 2”screws through
the predrilled holes (33). Install the provided trim pieces with the 1”trim nails to cover the raw edges of the roof panels
(34).
Image 28 Image 29
Image 29 Image 30
Image 31 Image 32
Image 33 Image 34

LOGAN INSTALLATION MANUAL
page 6
Step 11. Accessories
1. Install the vent hole cover using the provided screw and washer (35 & 36).
2. Install door handle with wood handle to the interior of the sauna (37 & 38).
Step 12. Finishing Touches
After the sauna has been installed, sweep down the inside to remove any sawdust and wood shavings, and then
vacuum completely. Using a damp cloth with warm water, wipe down the entire sauna including the benches to
remove any remaining dirt, dust and debris.
Step 13. Heater Installation
Please consult your heater manual for all heater installation information. All electrical connections must be
done by a qualied licensed electrician.
Image 35 Image 36
Image 37 Image 38

LOGAN INSTALLATION MANUAL
page 7
Optional Heater Fence Assembly
The heater fence kit will come banded in stretch wrap, remove the wrap and place the two pieces on your working
surface (39-40). Match the two pieces as shown below (41).
Turn over matched pieces so the long section is face down. Ensure the boards are ush in the top corner for optimal
tment (42). Attach the two pieces together using the two predrilled holes and remaining screws from your sauna
hardware kit (43). It is recommended to keep pressure on the two square boards during fastening for easier assembly.
See below for nished heater fence (44). To install heater fence into sauna, use the four predrilled holes and screws
from sauna hardware kit (45-46). Place fence around heater and fasten into side and front wall panels (47).
TRADITIONAL SAUNA USE
Congratulations! You are ready to enjoy your sauna! You may use your sauna in a wet or dry fashion. A dry sauna
means you do not sprinkle any water onto the stones, while wet means you increase the humidity of the room by
sprinkling water on the stones. Please note that not much water is needed to achieve a wet sauna experience!
The sauna as we know it originates in Finland. The typical sauna experience follows the steps below, but you may
enjoy your sauna in any way that you like!
• Set your heater so your sauna achieves the desired temperature. This is typically 150 -170+ degrees F. Please note,
novice sauna users should begin at the lower end of that range and increase their high temperature over time.
• Take a quick shower or a quick dip in a hot tub or pool.
• Step into the sauna and enjoy for 5-15 minutes, bringing a towel to sit or lay on. Leave the sauna once you are
perspiring freely.
• Take a plunge in a pool, shower, snowbank, lake - anything that will cool you down! After that, relax and cool down
for 10-20 minutes.
• Step into the sauna again. During this visit, you may wish to sprinkle small amounts of water onto the stones to
create bursts of steam. If water spills through the heater to the oor, you are using too much water, though this
will not hurt the heater or the sauna.
• Continue repeating this process. After your nal visit to your sauna, relax for at least 20 minutes. Shower with
warm water initially, nishing with cool water to close your skin pores.
• Prepare to feel refreshed for the day or to have an amazing night’s sleep!
Whatever your sauna routine, it is imperative that you STAY HYDRATED!
Image 39 Image 40 Image 41
Image 54 Image 55 Image 56 Image 57 Image 58 Image 59