Alphatech Slim IPDP - 01 User manual

DoorPhone VoIP
Slim IPDP –01
Slim IPDP –02
Slim IPDP –01C
Slim IPDP –02C
Slim IPDP –01C antivandal
Installation and Operating Instructions

Welcome
We congratulate you on purchase of “Slim IP Door phone -VoIP” (VoIP
= Voice over IP), which is the improved version of successful “New DoorPhone”
(NUDV). This DoorPhone VoIP will widely manage to satisfy your needs of
communication with persons at the building front door or your company entry,
or family house doorway. The universality lies in possibility to connect this
guard to an Ethernet network or VoIP exchange or directly to SIP server
through internet conection.
The basic DoorPhone VoIP module Slim IPDP-01 is supplied with 1
button, Slim IPDP-02 is supplied with 2 buttons The next version of basic VoIP
modules (Slim IPDP-01C and Slim IPDP-02C or Slim IPDP-01C antivandal)
is with integrated colour camera.
The Doorphone is supplied from AC/DC powersupply 12V or receives
power through the PoE (Power over Ethernet) technology. No additional
cabling fot power is therefore necessary.The basic features include the
possibility to open up to two doors by means of connected electrical locks (the
buttons can be used for door code opening). IPDP is configured over an
integrated web server, which can be controlled from any web browser, e.g., IE,
Mozilla Firefox.
Manual version V6.1 30-8-2011
Version of firmware V1.64 and V6.1
Alphatech spol. s r.o.
Jeremenkova 88
140 00 Praha 4
Tel/fax: [phone]
www.alphatech.cz / [e-mail]
The manufacturer continuously improves the product firmware. The
technology used allows you to upload to IPDP the latest version of the
firmware any time using a standard computer. The latest version of the
firmware is available at
http://www.alphatech.cz/ipdp-firmware/e_firmware.htm
You will find the necessary on page 29 of this manual. We recommend
that you use the latest version of the firmware, which brings new functions
and patches. At http://www.alphatech.cz/engl/e_ipdp-slim.htm you will
also find the latest version of the user documentation.

IPDP - installation and operating instructions
4
Table of Contents
DOORPHONE VOIP ............................................................................................................ 1
1BASIC DESCRIPTION................................................................................................ 5
1.1 FEATURES .............................................................................................................. 5
1.2 TERMINOLOGY ....................................................................................................... 6
1.3 MODULE ASSEMBLY ............................................................................................... 7
1.4 MODULE FEATURES ................................................................................................ 7
1.4.1 Slim IPDP Basic Module.................................................................................. 7
1.5 INSTALLATION OF DOORPHONE VOIP ASSEMBLY.................................................... 12
1.5.1 Open and close the cover of Slim IPDP .......................................................... 12
1.5.2 Dismounting lighting of nameplate.................................................................. 13
1.5.3 Assembly Slim IPDP on the wall...................................................................... 13
1.5.4 Return lighting name plate after mounting on the wall. .................................... 14
1.5.5 Change of nameplates ..................................................................................... 14
2DOORPHONE VOIP OPERATION.......................................................................... 15
2.1 SIGNALING OVERVIEW .......................................................................................... 15
2.2 VISITOR AT DOOR................................................................................................. 15
2.3 PERSON INSIDE OBJECT ......................................................................................... 16
2.3.1 Outgoing Call................................................................................................. 16
2.3.2 Incoming Call................................................................................................. 16
3PROGRAMMING OF PARAMETERS .................................................................... 17
3.1 BASIC VOIP SETTINGS........................................................................................... 17
3.1.1 Choosing a mode and login............................................................................. 17
3.1.2 Language option............................................................................................. 19
3.1.3 Network settings ............................................................................................. 20
3.1.4 Peer to peer or SIP server connection.............................................................. 22
3.1.5 Audio codec setting......................................................................................... 24
3.1.6 Setting video ................................................................................................... 25
3.1.7 Viewing the video (programme PopUp) ........................................................... 26
3.1.8 Day intervals .................................................................................................. 27
3.1.9 User interface................................................................................................. 28
3.1.10 Service settings .......................................................................................... 29
3.1.11 Restart ....................................................................................................... 31
3.1.12 Preparation style, language support ........................................................... 32
3.2 SETTING DOORPHONE PARAMETERS....................................................................... 33
3.2.1 Basic Parameters............................................................................................ 33
3.2.2 Sensors of open the doors............................................................................... 34
3.2.3 All about relays .............................................................................................. 35
3.2.4 Time Parameters............................................................................................. 37
3.2.5 Direct Dialing –Memories.............................................................................. 38
4TECHNICAL PARAMETERS .................................................................................. 39
4.1 ELECTRICAL PARAMETERS .................................................................................... 39
4.2 MECHANICAL DIMENSIONS .................................................................................... 39
4.3 PARAMETERS OF VIDEO,ACCESS ............................................................................ 40

IPDP - installation and operating instructions
5
1 Basic Description
1.1 Features
Voice communication is supplied only from telephone line
Two 25digit numbers (IP adress) with each button
Commands can be used for a doophone two or a single digit (command
55 is reduced to 5 so that we save * 5 instead of the original 55)
Day/night switching - automatic week program
Possibility of the call extension by * or # choice
Possible to connect two independent locks for door opening
Possible use of 5 switch modes (e.g. camera, lighting, gradual
opening)
Two codes for hanging up the doorphone from telephone
Two codes for door opening from telephone
Six code locks (password from buttons at the door)
two inputs for door sensors (open / close door)
Power supply 12V AC/DC, 500mA max or PoE technology
(IEEE802.3af Altern. A+B)
White LED for automatic ligting for camera
Permanent lighting through visiting cards
Included color camera (autofocus)
Ethernet –10/100Mb with standard 10BaseT a 100BaseTx
Web server for remote configuration –BOA
Operating system –Linux 2.6
USB for connection internal camera –USB guest 1.1, software
GSPCA software for video transmission to the browsers in PC –
W3CAM(J-PEG, RTSP Streem) and stream H.263, H.264
SIP connection P2P or PBX network system
WEB –firmware upgradeable
WEB –interface for control and setup parameters

IPDP - installation and operating instructions
6
1.2 Terminology
Ethernet is a family of frame-based computer networking technologies for local area
networks (LANs).
A local area network (LAN) is a computer network covering a small physical area,
like a home, office, or small group of buildings, such as a school, or an airport
10BASE-T runs over four wires (two twisted pairs) on a Category 3 or Category 5
cable.
100BASE-TX Uses two pairs, but requires Category 5 cable (FastEthernet)
Twisted pair cabling is a form of wiring in which two conductors (the forward and
return conductors of a single circuit) are twisted together for the purposes of
canceling out electromagnetic interference (EMI) from external sources.
UTP (unshielded twisted pair) cable is not surrounded by any shielding.
STP (shielded twisted pair) cables are often shielded in attempt to prevent
electromagnetic interference.
The World Wide Web (commonly abbreviated as the "Web") is a system of
interlinked hypertext documents accessed via the Internet.
Hypertext Transfer Protocol (HTTP) is an application-level protocol for distributed,
collaborative, hypermedia information systems.
Universal Serial Bus (USB) is a serial bus standard to connect devices to a host
computer.
A video codec is a device or software that enables video compression and/or
decompression for digital video. H.264 is a standard for video compression, and is
equivalent to MPEG-4 AVC. H.263 is a video codec standard originally designed as
a low-bitrate compressed format for videoconferencing. MPEG-4 is collection of
methods defining compression of audio and visual (AV) digital data.
JPEG is a commonly used method of compression for photographic images.
Voice over Internet Protocol (VoIP) is a general term for a family of transmission
technologies for delivery of voice communications over IP networks such as the
Internet.
The Internet Protocol Suite (commonly known as TCP/IP) is the set of
communications protocols used for the Internet
An Internet Protocol (IP) address is a numerical identification and logical address
that is assigned to devices participating in a computer network utilizing the Internet
Protocol for communication between its nodes.
Dynamic Host Configuration Protocol (DHCP) is a network application protocol
used by devices (DHCP clients) to obtain configuration information for operation in
an Internet Protocol network.
The Internet is a global system of interconnected computer networks that use the
standardized Internet Protocol Suite (TCP/IP).
An intranet is a private computer network that uses Internet technologies
Power over Ethernet or PoE technology describes a system to transfer electrical
power, along with data, to remote devices over standard twisted-pair cable in an
Ethernet network (we use only PoE standard IEEE802.3af Altern. A+B)
Network Time Protocol (NTP), a means of synchronizing clocks over a computer
network.

IPDP - installation and operating instructions
7
1.3 Module Assembly
The Slim IPDP are the basic modules with color camera Slim
IPDP-01/02C or without camera Slim IPDP-01/02. Antivandal panel is very
strong metal cover for increased endurance against vandalism.
Slim IPDP-01 Slim IPDP-02 Slim IPDP-01C Slim IPDP-02C
(Slim IPDP-01C antivandal)
1.4 Module Features
1.4.1 Slim IPDP Basic Module
The Slim IPDP basic module is assembling from modules IP, PoE
mudul, camera module and motherboard. Positioning setting elements and
connectors are on picture 1.
For Slim IPDP is necessary used PoE power from switch or the AC
voltage of min. 11Vst - max. 15Vst or DC voltage of min. 12Vss to max. 18Vss
must be energized to “12V” terminal. This source loading depends on number
of modules, since it simultaneously serves feeding of lighting through visiting
cards –at max. number of connected modules the demand will not exceed
300mA. This source can be also used for feeding of lock(s), and then it is
necessary to consider the electrical lock demand. In practice the alternating
feeder 12V/1A mostly meets these demands.
IPDP receives power through the PoE (Power over Ethernet - IEEE802.3af
Altern. A+B) technology. No additional cabling is necessary. If your Ethernet is
not equipped with the PoE technology it is possible to use a PoE adaptor. If
you use electric lock for opening door, so you must for supply of the lock use
power supply (only in circuit with relay - contact), or use low power lock and for
supply of the lock use connector on visiting - card (back lighting buttons) and at
supply by PoE is here 12V/350mA to disposal. Picture 4.

IPDP - installation and operating instructions
8
Picture 1 Basic module - motherboard
The connection of relay contact terminals is shown on pict. 2. The “NO”
designation means an idle-disconnected contact, “COM” means a pin contact
(middle) and “NC” means an idle-connected contact. The contacts of both
switches are galvanically isolated each other and from other guard circuits. The
variants of connection are shown on picture. 3 and 4.
The camera is mounted so that it can be tilted in the vertical direction (up-
down) so that optimal image occupy space in front of, or granted for the
installation of disabled people.

IPDP - installation and operating instructions
9
Picture 2. Connect Slim IPDP

IPDP - installation and operating instructions
10
Picture 3 Examples of relays connections
Picture 4 Examples of relays connections powered by PoE
ATTENTION - lock is must be low power consumption, max 350mA.

IPDP - installation and operating instructions
11
In newer versions available Slim IPDP function door sensor.
Refer. page 34.
Setting voice communication –
position trimmers are presetting
from manufacture and in majority
case agree with, therefore
changes setting altering only in
necessary case. Basic position
of trimmers, sense of rotation
and meaning trimmers are
illustration on picture 5.
Level of echo canceler adjust
silence of the microphone, to
make smaller acoustic feedback
and remove the echo
setting sensitivity of sensor
ambient lighting determine at what decrease ambient light will be automatically
switching lighting LED for camera. This function is accesible only if is activated
IPDP (by talking).
On picture 1. is two inputs for sensors in your IPDP. Door sensors are
sensors (eg magnetic contacts or part of electrical lock) to inform the opening /
closing doors. Check this option to display the status of the door to the home
screen video and sends this information to the program UDVguard where it is
displayed. Also information about status of this inputs is displayed on first WEB
site with video in WEB browser.
Picture 5 Setting of trimmers

IPDP - installation and operating instructions
12
DIP switch setting basic operation and default
setting. See on picture 6.
State of DIP switch is reading at start the IPDP, i. e.
after reset. After get started system is necessary DIP
switch 3 and 4 always return to the position "On",
because at next reboot system would be new values
overwriting by default value.
Picture 6 DIP switch settings
1.5 Installation of DoorPhone VoIP Assembly
1.5.1 Open and close the cover of Slim IPDP

IPDP - installation and operating instructions
13
1.5.2 Dismounting lighting of nameplate
1.5.3 Assembly Slim IPDP on the wall
The installation is made by screwing to the wall by means of dowels.

IPDP - installation and operating instructions
14
1.5.4 Return lighting name plate after mounting on the wall.
1.5.5 Change of nameplates
Each button has its separate nameplate hold by means of plastic flag
(see figure). The paper nameplates can be printed from Excel form (to be
downloaded on www.alphatech.cz/engl/basic.htm).

IPDP - installation and operating instructions
15
2 DoorPhone VoIP Operation
2.1 Signaling Overview
The IPDP signals an acoustic conditions they may occur during
operation. Another signaling can be done by means of red LED (placed under
microphone hole). You can listen the signaling samples in Nset setting
program.
Condition
Tones
Tone frequency
LED
Line lifting up
–▄–■–▀–
425-850-1275
Light
Line hanging up
–▀–■–▄
1275-850-425
Dark
Report after calling
–▄–■–▀–
425-850-1275
Light
Notice about call end
–■–■–■–
1275
Light
Parameter confirmation
––█––
Switch on (Reset)
–■–▄–■–
1275-850-1275
Blink
Error (anything, if unsuitable)
–■–■–■–■–■–■–
425….
Empty memory (no progr. numb.)
–█–▄–■–▄–■–▄–
850-1275-1700…
Waiting to talk
-
-
Blinking
Is talk
-
-
light
2.2 Visitor at Door
The IPDP function is influenced by setting of IPDP parameters.
The DoorPhone buttons are provided by nameplates or positions of
persons inside the object. The incoming person will press the corresponding
button, the DoorPhone will lift up the VoIP canale neither immediately (the
button is not the first number from code lock), or with delay and dial the
programmed phone number thru VoIP, but dial number differs by choice mode,
which is set in the DoorPhone :
- Day/night mode = being the DoorPhone in Day mode, so it is always
dialing a number set in table 1, in Night mode, it is always dialing a
number set in table 2. . Switching is possible use manual (two codes)
or automatic (table "Day intervals") and here you can set the switch
to three day intervals for 7 days a week. To facilitate proper function
is to set the IP address of the NTP server and network settings so
that the DoorPhone IPDP should have access to the Internet. In
automatic mode, day / night mode is also possible to use a
temporary manual switch, which cancels the first passage of the next
automatic switching interval.

IPDP - installation and operating instructions
16
- mode two number group = first press –it always dials a number set
in table 1. By repeated press of the same button or detection of busy
tone after dialing the DoorPhone will select the number from the
second group (table 2). The next press of the same button again
selects a number of the first group, etc..……
The switch (code lock) can be controlled by first 1-2 buttons of
DoorPhone. If the visitor at door presses buttons in such combination that meet
the preprogrammed code and the time among presses is not bigger than the
set point, then the DoorPhone will pick up and close the corresponding switch
(if set in m=1 or m=5 modes) to the period given by seting in parameters. Then
it will hang up.
2.3 Person Inside Object
The person inside object is considered a person that is in phone contact
with DoorPhone.
2.3.1 Outgoing Call
The outgoing call is the call from DoorPhone (caused by visitor). After
guard choice the telephone is ringing inside object and the pickuping up will
allow speaking to the visitor at door. The code choice can close the switch, if
set to m=1 or m=5 modes, change over the Day/Night modes and hang up the
DoorPhone. The DoorPhone in 10 seconds before call end will send a notice
about call end and the call may be extended by sign selection (* or #). The
telephone hanging up will end the call.
They are two possible means transmission information of push
buttons (command for opening lock, switch-over day/night, prolongation
conversation, command for hang-up) - by either in "RTP channels" or in
"SIP info", variant "inband DTMF" isn't in IPDP decoding.
2.3.2 Incoming Call
The incoming call is the call to the DoorPhone (caused by person inside
object). After exchange number selection, where the DoorPhone is connected,
the DoorPhone is ringing and when set number of rings is over, the DoorPhone
will pick up and it is possible to speak. The possibilities are the same as with
outgoing call.

IPDP - installation and operating instructions
17
3 Programming of Parameters
3.1 Basic VoIP settings
3.1.1 Choosing a mode and login
It is important to choose a DoorPhone mode
first. The DoorPhone can work in the PeerToPeer
mode or SIP server mode. The mode setting can be
made by a relevant switch (DIP switch see on picture
7). In the SIP server mode is possible to choose SIP
server (external). It can be set in a configuration
interface of the DoorPhone.
Setting values in doorphone to the firm setting
make by DIP switch 3 move to the position off and
reboot doorphone. After reboot system this switch is
necessary return to the position On.
Setting of basic IP address
192.168.1.250 make by DIP switch 4
move to the position off and reboot
doorphone. After reboot system this switch is necessary return to the position
On.
Reboot doorphone it is possible make by double ways –partly turn it off
and on again, or clicks on „Restart", in WEB site is at the entry service.
IP address of doorphone is from the manufacturer (as well as default)
setting on 192.168.1.250. If you are at installation in other numbering nets (=
NOT BEGINING 192.168.1.xxx) so is necessary setting in feature of protocol
TCP/IP in your PC IP address either temporarily or like alternative configuration
e.g . 192.168.1.245 . Then it is possible setting parameters of doorphone
including new IP address and after reboot VoIP module in doorphone you can
attach to WEB sites of the doorphone already on new IP address.
ATTENTION: DIP switch 3 and 4 must be in position "On", otherwise new IP
address after reboot module is re-write back on starting IP address =
192.168.1.250.
Picture 7 DIP switch setting

IPDP - installation and operating instructions
18
In your web browser enter IP address of the DoorPhone, default is
192.168.1.250. See picture 8.
Picture 8 First site - video from camera
Enter user name and password. User name is „admin“, default password
is „1234“. See picture 9.
Picture 9 Login to setup

IPDP - installation and operating instructions
19
3.1.2 Language option
Language setting can be made in a menu on the left panel. Adding language is
description on page 29

IPDP - installation and operating instructions
20
3.1.3 Network settings
Network settings are located in the Network seting menu item. It is possible to
use DHCP service (1) or you can enter IP addresses manually.
Manual configuration:
After making changes click on a save and restart button.
1. Hostname –name of doorphone for resolution in nets (e.g . while using
more doorphones –more entrance)
2. Enable/disable ethernet settings via DHCP
3. Setting IP address, mask, eventually next network parameters, in case
obscurity contact his IT manager
4. Display actual mode of IPDP –day / night
5. Return on introductory WEB site with display videos from cameras IPDP
6. short help for quick assistance in setting the parameters1 –
7. Default value –presetings to the firm settings. After making changes click
on a save and restart button (display screen - see page 31).