alpro AL2400-LP User manual

AL2400-LP model LED light
AL2400-LP model LED light model (Light Panel)
Vortex Door Magnet
AL2400-LP
Pack Contents Assembly
Swivel Pin Assembly
Light Feature
Read all instructions before starting installation
Introduction
Wiring & Power Input
The AL2400-LP series are SURFACE mount mounting. The AL2400-LP model
uses a miniature LED and a large strip LED for long distance door
monitoring and smarter look (see LED feature p3).
The AL2400-LP series needs DC and stabilised power. The voltage
(measured at the lock) must be correct for the magnet to retain the
armature plate with its highest holding force capacity. When an external
pressure is applied, the combined technology of magnetic force and
swivel pin held inside the magnet hole by six metal marbles will ensure a
holding force of > 15 000 N (~ 1 500 kgf). Cutting the power to the lock will
remove the magnetic force and the marbles release themselves from pin
head to unlock the door. The Vortex®AL2400-LP works in 12 or 24VDC. A
reed contact is integrated for a complete locking monitoring. This
monitoring only works if the armature plate is fitted flexibly and if the
power supply is correct at the lock input. Another reed contact provides
the door status. The exit button (or keypad, prox reader…) must be wired
on 12VDC (or 24VDC), not on the input wiring of power supply.
Also, this Vortex lock is equipped with a contact able to detect any
pressure on the door locked. This contact could be connected to an
alarm system or local alarm to warn BEFORE the access is opened without
authorisation. A built-in buzzer will sound simultaneously.
The PSU output must not be connected to the earth but isolated to avoid
any kind of electric sparks, therefore damaging the lock and its surfaces.
x4
x2
x2
x12 x4
x1
x1
x1
x1
x1
x1
x1
x1
1 x OIL
NO - DSS (BLUE)
NO (PURPLE)
COM (ORANGE)
NC (PINK)
NO-LSS (YELLOW)
- (BLACK)
NO - DSS (BLUE)
NO-LSS (YELLOW)
12/24 VDC
12VDC/0.36A, 24VDC/0.18A
30 VDC max
0.3 A max, 10 W max
30 VDC max
0.3 A max, 10 W max
EW, 50VDC,
0.3A max
Buzzer Enabled - Close
+(RED)
(BROWN)
(WHITE)
Buzzer Disabled - Open
To prevent irreversible damage to the unit, ensure that wiring is
connected correctly before supplying power to the mechanical
electro magnet.
We recommend using a 2 amp PSU (power supply unit) per lock.
To assure a solid locking from the magnet and its armature plate,
you need to mount the latter with FLEXIBILITY with help from the
rubber washer supplied. A over tighten central screw or not enough
power supply are the two main reasons why a magnet will not work
with efficiency.
Key screw
Spring
Pivoting Pin
Free-Angle
screw
rubber
Flat washer
Security top
sleeve nut
Flat washer
Anti-Tamper-Bracket
Tapped hole
Armature plate
Applied drop-wise
of provided thread-
lockers glue to the
thread of the
security sleeve nut
to prevent loosening
NOTE: Make sure to have the
rubber washer mount for absorbing
shock and obtaining the required
strength.

Bearing sleeve nut
5.5
30.5
218.0
30.0
Dimension of the holes in door for locating pin
is ø12, with a depth of 7mm
180.0
226.0
256.0
35.0
30.5
Armature plate
180.0
218.0
Secure firmly the
48AL2400-LP Mechanical
Electro Magnet on the
door frame.The provided
screws must be used in
accordance with the
frame or support
material. Also, the
screws must be checked
periodically to avoid
looseness.
PROBLEM POSSIBLE CAUSE SOLUTION
Door will
not lock
Holding
Force
reduced
There is a
delay in door
release when
power off.
Not enough DC voltage.
Wrong wire connection.
The screw centre is bad
positioned compared to
the magnet.
Bad physical contact
between armature plate
and magnet surface.
The power switch-off is
disturbed by the power
supply stabilisation.
Screw or contact supplier.
Make sure than surface
contact is cleaned and
well aligned with the
armature plate
Check wiring and refer
to wiring instruction.
Check power at lock
and wiring connection.
[email protected] www.alpro.co.uk
01202 676262 01202 680101
Registered in England & Wales 1925537 © November 2016 IEC. All rights reserved. All dimensions are nominal and subject to tolerances
Note: From factory, the voltage setting is 24VDC. For 12 VDC
installation, please select the jumper correctly.
Vortex Door Magnet
AL2400-LP
Installation Dimensions
Important Safety Information
The surface of contact
between the mechanical
electro magnet and the
armature plate must be kept
cleaned. Surfaces should be
cleaned periodically with a
non-abrasive cleaner. Do not
use cleaning chemical
products such as cleaning
solvents or varnish. This will
lead to serious problems
releasing the armature plate
from the magnet, damaging
the mechanism and causing
safety problems.
Maintenance Trouble Shooting
Read all instructions before starting installation
The power cut must be
done between the PSU
and lock. Not at the AC
input of the PSU.