Altronix AL1002ULADA User manual
Rev. 052313
AL1002ULADA
NAC Power Extender
Installation Guide
(See Application Guide for additional information)
AltronixCorp.
14058th St. Brooklyn, NY
- 2 - AL1002ULADA
Agency Listings:
• ULListedControlUnitsforFireProtective
SignalingSystems(UL864).
• MEA-NYCDepartmentofBuildingsApproved.
• CSFM-CaliforniaStateFireMarshalApproved.
• FM-FactoryMutualApproved.
• NFPA72Compliant.
Input:
• Powerinput120VAC60Hz,5.0amp.
• Two(2)ClassA,StyleZortwo(2)ClassB,
StyleW,YFACPinputs.
• Two(2)NCdrycontacttriggerinputs.
Output:
• Class2Ratedpower-limitedoutputs.
• 24VDC@10ampmaxtotalalarmcurrent.
• 2.5ampmaxcurrentperoutput.
• Separate1.0ampauxiliaryoutput.
• Programmablesupervisedindicatingcircuitoutputs:
Four(4)ClassB,StyleW,YorTwo(2)ClassA,
StyleZorOne(1)ClassA,StyleZandTwo(2)ClassB,
StyleW,Y(see Application Guide).
•Thermalandshortcircuitprotectionwithautoreset.
Battery Backup:
•Built-inchargerforsealedleadacidorgeltypebatteries.
•Automaticswitchovertostand-bybatterywhen
ACFails.
• Zerovoltagedropwhenswitchingoverto
batterybackup.
Supervision:
•ACfailsupervision(form“C”contact,1amp/28VDC).
Factorysetfor1.5hourswithoptional30seconds
delaysetting(fieldselectable).
• InstantlocalACtroublereportingrelay
(form“C”contact,1amp/28VDC).
•Batterypresenceandlowbatterysupervision
(form“C”contact,1amp/28VDC).
Visual Indicators:
•InputandoutputstatusLEDindicators.
Special Features:
• 2-wirehorn/strobeSyncmodeallowsaudible
notificationappliances(horns)tobesilenced
whilevisualnotificationappliances(strobes)
continuetooperate.
• SyncprotocolsincludePotter/Amseco,Faraday,
Gentex®,SystemSensor®,andCooperWheelock®.
• TemporalCode3,SteadyMode,InputtoOutput
FollowerMode(maintainssynchronizationof
notificationappliancescircuit).
• Compatiblewith12VDCor24VDCfirepanels.
•Outputloopsupervisionsteeredtoinput1orinput2.
• Signalcircuittroublememory(helpsidentify
intermittentloopproblems).
• Commontroubleinputandoutput.
• Groundfaultdetection.
•Unitincludespowersupply,redenclosure,camlock,
andbatteryleads.
Enclosure Dimensions (approx. H x W x D):
15.5”x12”x4.5”(393.7mmx304.8mmx114.3mm).
Overview:
TheAltronixAL1002ULADAisanextremelycosteffective10ampremotepowersupply/batterycharger.Itmaybecon-
nectedtoany12or24voltFireAlarmControlPanel(FACP).PrimaryapplicationsincludeNotificationApplianceCircuit
(NACsuchasstrobesandhorns)expansionsupporttomeetADArequirements.Italsoprovidesauxiliarypowertosupport
systemaccessories.Theunitdeliverselectronicallyregulatedandfiltered24voltpowertoClassB,StyleW,YorClass
A,StyleZNACloopcircuits.Additionally,aseparate1.0Aauxiliaryoutputforfour(4)-wiresmokedetectorsisavailable.
The10ampmax.alarmcurrentcanbedividedbetweenthefour(4)outputsforpoweringNACdevices.Eachoutputis
ratedat2.5ampmax.,andcanbeindependentlyprogrammedforSteady,TemporalCode3orStrobeSynchronization.All
outputsmaybeprogrammedforInputtoOutputFollowerMode(outputwillfollowinput).Innon-alarmconditioninde-
pendentloopsupervisionforClassA,StyleZand/orClassB,StyleW,YFACPNACcircuitsisprovided.Intheeventof
alooptrouble,theFACPwillbenotifiedviathesteeredinput(input1orinput2).Inaddition,therearecommontrouble
outputterminals(NC,C,NO)whichareusedtoindicategeneralloop/systemtrouble.Acommontroubleinputisprovided
foroptionalNC(normallyclosed)devicestoreporttroubletotheFACP.Two(2)FACPsignalingoutputscanbeemployed
anddirectedtocontrolsupervisionandpowerdeliverytoanycombinationofthefour(4)outputs.
Note:TheinformationinthisdocumentisvalidformodelsAL1002ULADAandAL1002UL2ADA.ModelAL1002ULADA
isequivalenttomodelAL1002UL2ADA.
Specifications:
AL1002ULADA - NAC Power Extender
AL1002ULADA - 3 -
Power Supply Specifications:
AC Input: 120VAC60Hz,5amp.
Output:
Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.
One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised
totaloutputcurrentmustnotexceedcurrent10ampinAlarmCondition.
Battery: Usetwo(2)12VDC/12AHortwo(2)12VDC/7AHbatteriesconnectedinseries.
Stand-by/Alarm Current
Consumption: 130mA/300mA
EOL Resistor
(end of line): 2.2K(2200ohm),AltronixModel#AL-EOL22(included).
Ground fault maximum
test impedance: 1000ohm.
Stand-by Specifications:
Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current Aux. Output
24VDC/7AH 24Hours 10amp/5minutes ---
24VDC/12AH
(usetwo(2)12VDCbatteriesinseries) 24Hours 10amp/5minutes 50mA
24VDC/36AH 24Hours 10amp/5minutes 1amp
Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power
outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for ratings. When
loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 10 amp total
alarm current (example: AUX = 1 amp, outputs up to 9 amp).
Installation Instructions:
WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA
72/ANSI,andwithalllocalcodesandauthoritieshavingjurisdiction.
Productisintendedforindooruseonly.
Carefully review:
Application Guide for AL602ULADA, AL802ULADA, AL1002ULADA
Power Supply Specifications (pg. 3)
Stand-by Specifications (pg. 3)
Output Programming Selection Table (pg. 4)
Sync Mode Selection Table (pg. 4)
Terminal Identification Table (pgs. 5-6)
LED Status Indication Table (pg. 6)
1.Mountunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholes
intheenclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placethe
enclosure’supperkeyholesoverthetwoupperscrews,levelandsecure.Markthepositionofthelowertwoholes.
Removetheenclosure.Drillthelowerholesandinstallthetwofasteners.Placetheenclosure’supperkeyholesover
thetwoupperscrews.Installthetwolowerscrewsandmakesuretotightenallscrews
(Enclosure Dimensions, pg. 12).
2. Connectgreenleadtoearthground (Fig 1).Connecttheline(L)andneutral(N)terminalstoaseparateunswitched
ACcircuit(120VAC,60Hz)dedicatedtotheFireAlarmSystem.
3. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.
4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).
Note:IfbatteriesbeingusedinyourinstallationdonotfitintotheAL1002ULADAunit,itisrequiredtoinstalla
separateenclosure,ULListedforappropriateapplication.Separatebatteryenclosureisrequiredtohave50cubicinches
ofadditionalopenspace.AllwiringmethodsshallbeinaccordancewiththeNationalElectricalCodeNFPA70/
NFPA72/ANSIandwithalllocalcodesandauthoritieshavingjurisdiction.Batterycircuitsarenotpower-limited;
provide0.25”spacingfrompower-limitedcircuitsanduseseparateknockout.Ifadditionalbatteryenclosure
isrequired,itmustbeULListedfortheapplicationandmountedwithin5’oftheAL1002ULADAenclosureinthe
sameroom;minimum12AWGwireinappropriateconduitisrequiredforconnection.Whenusingconduit,make
sureitisinstalledinamatterwhereitcannotturn.
5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]and
desiredoutputsignaltype (Output Programming Selection Table, pg. 4).
L N
line
ground
neutral
Fig. 1
- 4 - AL1002ULADA
6. ConnectFACPoutputtodesiredAL800LGKlogicboardinputs,andnotificationappliancestodesiredAL800LGK
logicboardoutputs(see Application Guide).
Note:The2-wirehorn/strobesyncmodewillonlysynchronizehorns,horn/strobes,strobeswith
synchronizationcapability.
7. Forconnectionofsmokedetectors,digitaldialersee Optional Hookup Diagram, pg. 8.
Class A, Style Z Class B, Style W, Y, SW1 & SW2 Settings:
• ForallClassB,StyleW,Y,hookupsSW1&SW2ontheAL800LGKlogicboardmustbeopen.
ForallClassA,StyleZhookupsSW1&SW2ontheAL800LGKlogicboardmustbeclosed.
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function Switch Positions Descriptions
ON OFF
InputtoOutput
FollowerMode 1 2,3 Outputfollowssignalitreceivesfromthecorrespondinginput(i.e.FACP
Syncmodule-maintainssynchronizationofnotificationappliancecircuit).
Temporal
Code3Mode 3 1,2 EnablesTemporalCode3signalgenerationoutput.
Thismodewillacceptasteadyorapulsinginput.
SteadyMode 1,2,3 Asteadyoutputsignalwillbegenerated.
Thismodewillacceptsteadyorpulsinginput.
For the above modes Dip Switch 4 determines which Input controls
the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by input 1.
Switch 4 in the OFF position causes output(s) to be controlled by input 2.
Sync Mode Selection Table:
Function Switch Positions Descriptions
ON OFF
AmsecoSync
Mode*
1,3,
42
ThismodeisdesignedtoworkwiththeAmsecoseriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchro-
nizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobe
combinationoveratwo-wirecircuitwhileleavingstrobesactive.
Faraday
SyncMode* 2,4 1,3
ThismodeisdesignedtoworkwiththeFaradayseriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchroniz-
ingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobecombina-
tionoveratwo-wirecircuitwhileleavingstrobesactive.
Gentex®
SyncMode*
Gentexisaregisteredtrademark
ofGentexCorporation.
1,2,
3,4
ThismodeisdesignedtoworkwiththeGentex®seriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchroniz-
ingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobecombina-
tionoveratwo-wirecircuitwhileleavingstrobesactive.
SystemSensor®
SyncMode*
SystemSensorisaregistered
trademarkofHoneywell.
1,2,4 3
ThismodeisdesignedtoworkwiththeSystemSensor®seriesofhorns,strobes,and
horn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,syn-
chronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsofthe
horn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
CooperWheelock®
SyncMode*
CooperWheelockisa
registeredtrademarkof
CooperWheelock.
2,3,4 1
ThismodeisdesignedtoworkwiththeCooperWheelockseriesofhorns,strobes,
andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof
thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
*Note:TheAL1002ULADAwillonlysynchronizehorns,horn/strobesandstrobesthatcontainsynchronizationcapability.
Contactsignalmanufacturerformoredetailedinfo.Thesamesynchronizationmodemustbeselectedforalloutputs.
Note: It is required to control visual notification appliances (strobes) via input 1 (IN1) and audible notification
appliances (horns) via input 2 (IN2). This allows audible notification appliances (horns) to be silenced while
visual notification appliances (strobes) continue to operate.
(AL800LGK Board)
Output Dip Switches
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC
AL1002ULADA - 5 -
Amount of Notification Appliances per NAC:
Amseco 27perNAC* SystemSensor® 32perNAC*
Faraday 39perNAC* CooperWheelock® 32perNAC*
Gentex® 32perNAC*
*Not to exceed a maximum of 2.5 amp per NAC.
Terminal Identification Table:
AL800LGK Logic Board
Terminal
Legend Function/Description
IN1+,IN1-
IN2+,IN2-
(Supervised)
Theseterminalsconnecttothe12VDCor24VDCFACPnotificationappliancecircuitout-
puts.(ClassA,StyleZorClassB,StyleW,X,Y)Inputtriggervoltageis8-33VDC@5mAmin.
Terminalpolarityisshowninalarmcondition.Duringanalarmconditiontheseinputswillcause
theselectedoutputschosentodrivenotificationappliances.Thedesignatedoutputsaresetbyoutput
switches[OUT1throughOUT4](Output Programming Selection Table, pg. 4). Atroubleconditionon
anoutputloopwillcausethecorrespondinginputtotriptheFACPbyopeningtheFACPloop.An
alarmconditionwillalwaysoverridetroubletodrivenotificationappliances.
RET1+,RET1-
RET2+,RET2-
(Supervised)
ForClassA,StyleZhookupstheseterminalpairsreturntoFACPNAC1and/orNAC2.For
ClassB,StyleW,X,YhookupstheFACPEOLresistorfromtheNAC1and/orNAC2outputs
areterminatedattheseterminals.
C“DRY1”NC
C“DRY2”NC
(Dryinputtrigger)
Anopenacrosstheseinputs,willcausetheselectedoutputschosentodrivenotification
appliances.Thedesignatedoutputsaresetbyoutputswitches[OUT1throughOUT4](Output
Programming Selection Table, pg. 4).Notetheseinputsareunidirectionalandwillnotreport
atroubleconditiontotheFACP.
+OUT1--
+OUT2--
+OUT3--
+OUT4--
(Supervised)
Notificationappliancesareconnectedtotheseregulatedoutputs (see Application Guide pg. 2-4).
Eachpower-limitedoutputwillsupply2.5amp.Two(2)outputsmaybeconnectedinparallelfora
maximumNACoutputcapabilityof4amp.Totalsupplycurrentis10amp(see note below).Outputs
arecontrolledbydesignatedinput1[IN1]orinput2[IN2](Output Programming Selection
Table, pg. 4). Maximumlinelossorvoltagedrop(testedwith2.5V).
C“FAULT”NC
(Common
troubleinput)
Anopencircuitacrossthispairofterminalswillcause[IN1andIN2]tosimultaneouslysignala
troubleconditionbacktotheFACP(TypicallyusedtoreportACorBATFail).(form“C”contact
1amp/28VDC)(Fig. 3, pg. 8).
NC,C,NO
(Common
troubleinput)
Thesearedrycontacttroubleoutputsthatfollowanygeneralloop/systemtroubleconditions.
(Typicallyusedtotriggeradigitalcommunicatororotherreportingdevice).
(form“C”contact1amp/28VDC0.35PowerFactor)(Fig. 3, pg. 8).
--AUX+ Thisseparate1ampmax.auxiliarySpecialApplicationPoweroutputcircuitistypicallyusedto
power4-wiresmokedetectors.Seeattachedlistofdevices(Appendix A, pgs. 10-11).
+DC-- 24VDCfrompowersupply.
Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power
outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for ratings. When
loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 10 amp total
alarm current (example: AUX = 1 amp, outputs up to 9 amp).
- 6 - AL1002ULADA
Terminal Identification Table:
Power Supply Board*
Terminal Legend Function/Description
L,N Connect120VACtotheseterminals:Ltohot,Ntoneutral(Fig. 2, pg. 7).
-DC+ 24VDC@10ampinalarmnonpower-limitedoutput(Fig. 2, pg. 7).
ACFAIL
NO,C,NC
Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciationdevices,
withACpresentterminalsmarkedNOandCareopen,NCandCareclosed.WhenlossofAC
occursterminalsmarkedNOandCareclosed,NCandCareopen.
ACLOCAL
NC,NO,C
Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciationdevices,
withACpresentterminalsmarkedNOandCareopen,NCandCareclosed.WhenlossofAC
occursterminalsmarkedNOandCareclosed,NCandCareopen.
BATFAIL
NO,C,NC
Form“C”drycontactsusedtosignallowbatteryvoltageorlossofbatteryvoltage.Undernormal
conditionsterminalsmarkedNOandCareopen,NCandCareclosed.Duringatroublecondition
terminalsmarkedNOandCareclosed,andNCandCareopen(Fig. 3, pg. 8).
+BAT- Stand-bybatteryinput(leadsprovided)(Fig. 3, pg. 8).
*Power Board Parameter Specifications:
• ACFailconditionwillreportapproximately1.5hoursafterlossofAC.TosetACDelayto30seconds,powertheunit
down(ACsupplyandBattery)priortochangingswitchposition.
OpenSwitch“ACDelay”orclose“ACDelay”switch,respectively.
• Lowbatteryconditionwillreportatapproximately20VDC.
• Batterypresencedetectionwillreportwithin180secondsafterbatteryremainsundetected(missingorremoved).
Arestoredbatterywillreportwithin30seconds.
LED Diagnostics:
Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normaloperatingcondition.
ON OFF LossofAC,Stand-bybatterysupplyingpower.
OFF ON NoDCoutput.
OFF OFF LossofAC.Dischargedornostand-bybattery.NoDCoutput.
AL800LGK - Logic Board
LED OFF ON BLINK (LONG)* BLINK (SHORT)**
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
Input1 Normal AlarmCondition TroubleCondition ---
Input2 Normal AlarmCondition TroubleCondition ---
Fault Normal AlarmCondition --- ---
* Indicatescurrenttroublecondition.Whentrouble(open,shortorground)occursonaspecificoutput,the
correspondingredoutputLED,[OUT1-OUT4]willblink.ThecorrespondinggreeninputLEDwill
blinkaswell.Looptroublewillreportwithin30seconds.
**Indicatestroubleconditionmemory.Whenatroubleconditionrestores,theunit’sredoutputLED[OUT1-OUT4]
willblinkwithashorteranddistinctlyadifferentduration.ThegreeninputLEDswillbeoff(normalcondition).
Toresetthememorydepresstheresetbutton(Fig. 3c, pg. 8).TheLED(s)willextinguish.
Note:Ifindicatingcircuitshavebeenrestored,memoryresetisnotrequiredfornormaloperationoftheunit.
AL1002ULADA - 7 -
External
Jacketed
Shield
Incorrect Wire
Handling
Correct Wire
Handling
Pull back
external jacketed
shield approx. 1/2”.
Wire
Insulation
Solid Copper
Conductors
NEC Power-Limited Wiring Requirements for AL1002ULADA Models:
Power-limitedandnonpower-limitedcircuitwiringmustremainseparatedinthecabinet.Allpower-limitedcircuit
wiringmustremainatleast0.25”awayfromanynonpower-limitedcircuitwiring.Furthermore,allpower-limited
circuitwiringandnonpower-limitedcircuitwiringmustenterandexitthecabinetthroughdifferentconduits.Onesuch
exampleofthisisshownbelow.Yourspecificapplicationmayrequiredifferentconduitknockoutstobeused.Anycon-
duitknockoutsmaybeused.Forpower-limitedapplications,useofconduitisoptional.Allfieldwiringconnectionsmust
bemadeemployingsuitablegaugeCMorFPLjacketedwire(orequivalentsubstitute).
OptionalbatteryenclosuremustbemountedadjacenttothepowersupplyviaClass1wiringmethods.
Note:Refertowirehandlingdrawingbelowfortheproperway
toinstalltheCMorFPLjacketedwire,(Fig, 2a).
Fig, 2
Fig, 2a
120VACInput
60Hz
(nonpower-
limited)
SupervisoryConnections
(power-limited)
non-supervised
Battery
Connections
(nonpower-
limited)
supervised
Aux.
Output
(power-limited)
non-supervised
NAC
Circuits
(power-limited)
supervised
Signaling
Circuits
fromFACP
(nonpower-
limited)
supervised
- 8 - AL1002ULADA
Optional hookups:
1- BatteryandACmonitoring:ACorBatteryFailconditionwillcausethecommontroubleinput[C“FAULT”NC]to
reportbacktotheFACPviainput1andinput2.Thecommontroubleinputmayalsobeusedforotheroptional
supervisorymonitoring.
ToreportACandBatteryTroubleconnectthebatteryandACFailrelayoutputshownin(Fig. 3a, Pg. 8)tothe
commontroubleinput.
2- Drycontactinput(C“DRY1”NC)(C“DRY2”NC)canbeusedtoalarmoutputfroman
addressablemodule(theseinputsareunidirectionandcannotreportbacktotriggermodule).
Connection to triggering devices must be made within 20ft. of distance and using conduit for wiring.
3- Auxiliaryoutput(-AUX+)24VDCat1ampmax.
4- ACLocal[NC,NO,C]shouldconnecttothehostcontrolpanelforlocalannunciationof
thetroublecondition.
Note: Ifcommontroubleinput,terminalsmarked[C“FAULT”NC]arenotused,theseterminalsmustbe
shorted(connectjumper)toremaininactive.Foroptionalhookups(Fig. 3b, Pg. 8).
Optional Hookup Diagram:
Fig. 3
Maintenance:
Unitshouldbetestedatleastonceayearfortheproperoperationasfollows:
Output Voltage Test:Undernormalloadconditions,theDCoutputvoltageshouldbecheckedforpropervoltagelevel
(26.2-26.4VDC recommended range).
Battery Test:Undernormalloadconditionscheckthatthebatteryisfullycharged.Checkspecifiedvoltage
bothatbatteryterminalandattheboardterminalsmarked[+BAT--]toensurethatthereisnobreakinthebattery
connectionwires.
Fuses:Checkinputandoutputfusesonthepowersupplyboard,replaceifnecessary.Inputfuseratingis6.3amp@
250V,Outputfuseratingis15amp@32V.
Note:Maximumchargingcurrentis1.5amp.
Note:Expectedbatterylifeis5years;however,itisrecommendedchangingbatteriesin4yearsorlessifneeded.
These circuits are used to monitor AC and
Bat Fail and will cause a simultaneous trouble
condition to the FACP's IN1 and IN2 (Non-Supervised)
4-wire Smoke
Detector
+
--
+
--
4-wire Smoke
Detector
Fire Alarm
Control Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from FACP
SW1
-- DC +
SW2
+ OUT1 --
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC C NO C "FAULT" NC
OUT1 OUT3
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1-- IN2--
IN2+ C "DRY1" NC
RET1+
RET1-- RET2--
RET2+ C "DRY2" NC
+ OUT2 -- + OUT3 -- + OUT4 --
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
-- AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable Control
Module Trigger Output
See Note 2
(Non-Supervised)
RESET
Supervised
Non-Supervised Input from
Power Supply
BAT FAIL
AC FAIL
DC AC
AC DELAY
NC C NO NC C NO
AC LOCAL
NC C NO
L
N
6.3A 250V
Digital Communicator
or Local Annunciator
Dry output Contact
(Form "C" contacts)
Power-Limited Outputs
2.5 amp per output in alarm
Total = 10 amp
(Supervised)
AC FAIL
NC C NO
BAT FAIL
NC C NO
Fig. 3a
-- DC +
OUT1 OUT3
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
RESET
Fig. 3c
TroubleMemory
ResetButton
Fig. 3b
Common
trouble
Input/Output
NC CNOC"FAULT" NC
AL1002ULADA - 9 -
Battery Calculation Worksheet
Device Number of
Devices Current per Device Stand-by
Current
Alarm
Current
Foreachdeviceusethisformula: Thiscolumn x Thiscolumn = Equals Currentpernumberofdevices.
AL1002ULADA
(Currentdrawfrombattery) 1Stand-by: 130mA 130mA
Alarm: 300mA 300mA
AAL1002 Current 130mA 300mA
AuxiliaryDevices Refertodevicemanualforcurrentratings.
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
BAuxiliary Devices Current (must not exceed 1 amp)
Refertodevicemanualforcurrentratings.
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
CNotificationAppliancesCurrent must notexceed10amp(10,000mA) 0mA mA
DTotalalarmcurrent mA mA
ETotalcurrentratingsconvertedtoamperes(lineDx0.001) A A
FNumberofstand-byhours(24forNFPA72,Chapter1,1-5.2.5). H
GMultiplylinesEandF. Totalstand-byAH AH
HAlarmsoundingperiodinhours.
(Forexample,5minutes=.0833hours.) H
IMultiplylinesEandH. TotalalarmAH AH
JAddlinesGandI. Totalstand-byandalarmAH AH
K
MultiplylineJby1.30.
(30%extrainsurancetomeetdesiredperformance)
Totalampere-hoursrequired
AH
Unitsarecapableofrecharging36AHbatterymax.Iftotalampere-hourrequiredexceeds36AH,
decreaseAUXcurrenttoprovideenoughstand-bytimefortheapplication.
- 10 - AL1002ULADA
Appendix A - UL Listed Compatible Devices
A.1 Four (4) Wire Smoke Detectors
TableA-1belowlistsfour(4)wiresmokedetectorscompatiblewithAL1002ULADAAUXoutput.
Smoke Detector/BaseDetector Type Max Standby
Current (mA)
Alarm
Current (mA)
FenWalCPD-7021(w/70-201000-005Base) Ionization 0.10 *
FenWalPSD-7125 Photoelectric 0.10 *
FenWalPSD-7125(w/70-201000-005Base) Photoelectric 0.10 *
Fire-LiteBLP-12-4W Base * *
Gentex824 Photoelectric 0.50 *
Gentex824T Photoelectric 0.50 *
Gentex824CP Photoelectric 0.50 *
Gentex824CPT Photoelectric 0.50 *
HochikiHSC-4R Base * *
HochikiSPB-24 ProjectedBeam 0.25 *
SystemSensorB112LP Base 0.12 36
SystemSensorB114LP Base * *
SystemSensorB404B Base * *
SystemSensorDH100ACDC Photoelectric 0.15 0.70
SystemSensorDH100ACDCLP Photoelectric 0.15 0.70
SystemSensorDH100ACDCLPW Photoelectric 0.15 0.70
SystemSensorDH400ACDCI IonizationDuct 25 95
SystemSensorDH400ACDCP PhotoelectricDuct 25 95
SystemSensor1112/24/D Ionization 0.05 50
SystemSensor1424 Ionization 0.10 41
SystemSensor1451(w/B402BBase) Ionization 0.10 39
SystemSensor2112/24ATR Photoelectric 0.50 60/70
SystemSensor2112/24AITR Photoelectric 0.50 60/70
SystemSensor2112/24/D Photoelectric 0.05 50
SystemSensor2112/24R Photoelectric 0.50 60/70
SystemSensor2112/24TR Photoelectric 0.50 60/70
SystemSensor2112/24T/D Photoelectricw/135oThermal 0.05 50
SystemSensor2112/24TSRB Photoelectricw/135o
ThermalSupervisoryRelay 15 45
SystemSensor2312/24TB Photoelectric 0.12 50
SystemSensor2412(12volt) Photoelectric 0.12 77
SystemSensor2412AT(12volt) Photoelectric 0.12 58
SystemSensor2412TH(12volt) Photoelectric 0.12 77
SystemSensor2424 Photoelectric 0.10 41
SystemSensor2424TH Photoelectric 0.10 41
SystemSensor2451 Photoelectric 0.10 39
SystemSensor2451TH(with/B402BBase) Photoelectric 0.10 39
SystemSensor2W-MOD LoopTest/MaintenanceMod. 30 50
AL1002ULADA - 11 -
A.1 Four (4) Wire Smoke Detectors (cont.)
Smoke Detector/BaseDetector Type Max Standby
Current (mA)
Alarm
Current (mA)
SystemSensor4W-B(12/24volt) PhotoelectricI3.05 23
SystemSensor4WT-B(12/24volt) PhotoelectricI3w/Therm .05 23
SystemSensor4WTA-B(12/24volt) I3Photow/Therm/Sounder .05 35
SystemSensor4WTR-B(12/24volt) I3Photow/Therm/Relay .05 35
SystemSensor4WTR-B(12/24volt) I3Photow/Therm/
Sounder/Relay .05 50
SystemSensor4WITAR-B(12/24volt) I3Photow/IsolatedTherm/
Sounder/Relay .05 50
SystemSensor2W-MOD2 I3LoopTest/Maintenance
Mod. .05 *
SystemSensorRRS-MOD I3ReversingRelay/Sync
Module .05 *
SystemSensor6424 ProjectedBeam 10 28.4
SystemSensorBeam1224(S) ProjectedBeam 17 38.5
*Contactmanufacturerforcurrentdraws
A.2 Door Holders
TableA-2belowlistsdoorholderscompatiblewithAL1002ULADAAUXoutput.
Manufacturer Model Type Current (mA)
Edwards DH150A FloorMount 96
Edwards DH154A FloorMount 96
Edwards DH158A SurfaceMount 96
RixonFiremark FM-980 FloorMount,single 68
RixonFiremark FM-996 SurfaceWiring 68
RixonFiremark FM-998 ConcealedWiring 68
A.3 Relays
TableA-3belowlistsrelayscompatiblewithAL1002ULADAAUXoutput.
Manufacturer Model Current (mA)
AirProducts&
Controls,LTD
MR-101/C
MR-201/C
PAM-1
PAM-2
PAM-SD
A77-716B
15
35
15
15
15
20
Manufacturer Model Current (mA)
SystemSensor
PR-1
PR-2
PR-3
EOLR-1
R-10T
R-14T
R-20T
R-24T
R-10E
R-14E
R-20E
R-24E
15
30
30
30
23
23
40
40
23
23
40
40
- 12 - AL1002ULADA
Enclosure Dimensions (H x W x D approx.):
15.5”x12”x4.5”(393.7mmx304.8mmx114.3mm)
MEMBER
Altronixisnotresponsibleforanytypographicalerrors.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IIAL1002ULADA I04M
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
5.0”
(127.0mm)
5.0”
(127.0mm)
1.5”
(38.1mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
1.75”
(44.45mm)
1.75”
(44.45mm)
4.5”
(114.3mm)
1.25”
(31.75mm)
4.5”
(114.3mm) 1.25”
(31.75mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.1”
(27.94mm)
1.1”
(27.94mm)
0.79”
(20.06mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
0.91”
(23.114mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
15.5”
(393.7mm)
4.615”
(117.22mm)
12.23”
(310.64mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
Other manuals for AL1002ULADA
1
Table of contents
Other Altronix Extender manuals
Altronix
Altronix FireSwitch108 User manual
Altronix
Altronix AL802ULADAJ User manual
Altronix
Altronix AL802ADA220J User manual
Altronix
Altronix AL1002ULADA User manual
Altronix
Altronix AL602ADA220J User manual
Altronix
Altronix AL642ULADA User guide
Altronix
Altronix AL602ULADAJ User manual
Altronix
Altronix AL642ULADA User manual
Altronix
Altronix AL1042ADA220 User manual
Altronix
Altronix AL602ULADAJ User guide
Altronix
Altronix AL602ULADA User manual
Altronix
Altronix AL802ULADA User manual
Altronix
Altronix AL1042ULADA User manual
Altronix
Altronix AL602ULADA User guide
Altronix
Altronix AL602ULADAJ User guide
Altronix
Altronix Pace1STR User manual
Altronix
Altronix AL642ULADA User guide
Altronix
Altronix AL842ULADA User manual
Altronix
Altronix AL1002ULADAJ User manual
Altronix
Altronix AL602ULADA User guide
