Amantii FS-26-922 Owner's manual

INSTALLATION ANDOPERATION INSTRUCTIONS FOR ZEROCLEARANCE
ANDFREE STANDING UNITS
FS-26-922
SAFETY INFORMATION
WARNING
If theinformationintheseinstructionsare
not followed exactly,afireorexplosion
mayresult causingpropertydamage,
personalinjuryorlossoflife.
Do not storeoruse gasolineorotherflammablevapors
and liquidsinthevicinity ofthisorany otherappliance.
INSTALLER: LEAVE THIS MANUAL WITHTHEAPPLIANCE.
CONSUMER: RETAINTHIS MANUAL FOR FUTURE REFERENCE.

2
IMPORTANTINSTRUCTIONS....................................................................................................................................3
UNPACKING ANDTESTINGAPPLIANCE...............................................................................................................7
LOCATINGTHEFIREPLACE.....................................................................................................................................7
FS-26-922.......................................................................................................................................................................
MEDIAOPTIONS.........................................................................................................................................................9
DECORATIVEMEDIAINSTALLATION....................................................................................................................9
OPERATION............................................................................................................................................................... 10
MANUALOPERATION............................................................................................................................................. 10
REMOTE CONTROLOPERATION...........................................................................................................................11
CARE AND MAINTENANCE ....................................................................................................................................14
REPLACEMENTPARTS............................................................................................................................................15
EXPLODEDVIEW......................................................................................................................................................16
WIRING DIAGRAM...................................................................................................................................................17
TROUBLESHOOTING..............................................................................................................................................18
SERVICE HISTORY....................................................................................................................................................19
WARRANTY...............................................................................................................................................................20
8
PLUG INSTALLATION INSTRUCTIONS..................................................................................................................6
TABLE OF CONTENTS
Pleasereadandcarefullyfollowalloftheinstructionfoundinthis manual.Pleasepayspecial
attentiontothesafetyinstructionsprovided inthismanual.Theinstructionsincludedhere will assure
thatyouhavemanyyearsofdependableand enjoyableservicefromyourAmantii product.

3
IMPORTANT INSTRUCTIONS
Please read the following instructions carefully before using the appliance.
Caution - Fire, electric shock, physical injury and material damage hazards:
To use the appliance, always follow the instructions for assembly, use and maintenance as well as
usage cautions:
1. Carefully read and retain these instructions.
2. Before connecting the appliance, be sure that the mains voltage available matches that specified
on the rating plate.
3. Do not use the appliance for other than its intended use. For domestic indoor use only.
4. There may be trace of odour during the first few minutes of initial use. This is normal and will
quickly disappear.
5. The heater is hot when in use. To avoid burns, do not let bare skin touch any hot surface.
6. Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at
least 1m away from the heater.
7. Do not use the heater in areas where flammable liquids are stored or where flammable fumes
may be present.
8. Do not cover or obstruct any of the heat outlet grilles or the air intake openings of the heater.
9. Do not use the heater in the rooms with explosive gas or while using inflammable solvents,
varnish or glue.
10. Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as
this may cause electric shock, or fire or damage to the heater.
11. Always unplug or disconnect the appliance from the mains power supply when not in use or
when moving or cleaning it. Do not pull the cord to unplug the heater.
12. Do not immerse the cord, plug or any part of the appliance in water or any other liquid.
13. Do not attempt to repair, disassemble or modify the appliance. There are no user-serviceable
parts inside.
14. The heater must not be located immediately below a socket-outlet.
15. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
16. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.
17. Do not use this heater with a programmer, timer, separate remote-control system or any other
device that switches the heater on automatically, since a fire risk exists if the heater is covered or
positioned incorrectly.
18. WARNING: In order to avoid overheating, do not cover the heater.
19. WARNING! – DO NOT COVER THIS APPLIANCE WITH ITEMS SUCH AS CLOTHING, BLANKETS OR
PLACE NEXT TO CURTAINS OR NET/BLINDS.
20. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
21. Do not use this heater in small rooms when they are occupied by persons not capable of leaving

4
the room on their own, unless constant supervision is provided.
22. If the glass is damaged, do not use the heater in order to avoid a hazard.
23. Children of less than 3 years should be kept away from unless continuously supervised.
24. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided
that it has been placed or installed in its intended normal operating position and they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved, Children aged from 3 years and less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
25. CAUTION Some parts of this product can become very hot and cause burns. Particular attention
has to be given where children and vulnerable people are present.
26. This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
27. The heater may emit a slight, harmless odour and smoke when first used. This odour and smoke
is normal and it is caused by the initial heating of internal heater parts and will not occur again.
28. DO NOT plug into an extension lead/cable or plug adaptor.
29. DO NOT cut off the plug and hardwire directly into the mains or via a fused fixed spur.
30. For details about installing the fireplace, please refer to “Installation” section.

Cautions
Do’s
·Always install the heater in accordance with this guide. If in
doubt obtain expert advice.
·Always make sure the electrical socket is accessible and located
adjacent to, but not above the heater.
·Always disconnect the heater from the electrical supply before
moving it, or carrying out cleaning, maintenance.
·Always make sure the heater is firmly secured to prevent it from
being tipped over.
·Always use a fireguard when young children and infirm persons
can come into contact with the heater.
Don’ts
·Never leave children unsupervised in a room where the heater is
ON and unguarded.
·Never obstruct or cover the fan outlet or force items into heater
openings.
·Never install or use the heater anywhere where water is in use,
i.e. Bathrooms, Kitchens, Shower Rooms, and Swimming Pool etc.
·Never use aerosols or steam cleaners on or around the heater.
·Never route the mains supply cable under carpet etc.
·Never install the heater close to curtains or combustible
materials.
·Never use the heater to dry clothes etc.
·Never sit or stand on the heater.
·Never use with a timer or any other device that switches the fire
on automatically.
5

PLUG INSTALLATION
Your power cord will come separate from the unit, please locate it when unpacking
your fireplace. The plug contained inside the box is predetermined at the factory and
according to orders placed by authorized dealers.
Available are UK, European & Swiss plugs. Should you require any of these options
please contact your dealer for purchase. You will be required to give them the correct
part number as listed below.
UK plug European plug Swiss plug
10103060E 10103030E 10103109E
Please follow the instructions to correctly install the plug into your fireplace.
1. Included in the box will be a power cord similar to the one pictured below.
2. Hold the male plug and insert it into the female receptacle. The receptacle is
located on the left side of the fireplace.
Picture 1 Picture 2
3. Please make sure the plugs are firmly connected. See Picture 2 above.
See Picture 1.
6

7
LOCATINGTHEFIREPLACE
Plan where tolocateand framethefireplace.Considerthefollowing:
1. Consideralocationwhere thefireplacescreenwill notbeexposedtodirectsunlight from
windowsordoors.
2. A15 ampere,240 Volt,50 Hz branchcircuit with properground mustbeavailableatthelocation.
Preferablyadedicatedbranchcircuitshouldbeprovidedtoavoidcircuitbreakerstotripoffuses
toblow.
UNPACKINGANDTESTINGAPPLIANCE
Carefullyremovetheappliancefromthebox.
Priortoinstallingtheappliance,testtomakesuretheapplianceoperatesproperlybypluggingthe
powersupplycordintoaconvenientlylocated 240 Volt grounded outlet.
Testallaspectsofitsoperation(manualswitches, remoteand heater)tomakesure all components
operatecorrectly.

8
FS-26-922
Description Free StandingAppliance
Voltage 240V AC50-60Hz
Watts 1900WMax
NOHEATER 18.5W
MOTOR HEATER 19W
ApplianceWidth 25 5/8" or 65.2 cm
ApplianceHeight 28" or 71.2 cm
ApplianceDepth 17 1/2" or 44.5 cm
Gross Weight 71.6 lbs or 32.5 kgs
PlugLocation Left side
Cord Length 707/8”or180 cm
BTU 6500

9
MEDIAOPTIONS
Sable
DECORATIVEMEDIA INSTALLATION
STEP1: Unplugtheunitfromwall and make
surecontrols are switched off.
STEP2: Pushupwards(asshowsinbellow
picture)andremovethefront paneltodecorate
yourfireplace.Pourthedecorativemediainto
thetray.Feelfree touseanycombinationoffire
glass mediathatyoufindmostappealing.
STEP3: Afterfinishingdecoration,putbackthe
Log Set 11 pieces
Hold here firmly, then push upwards to take off
the front glass panel.
The glass panel is hooked by 2 hooks on each
side.
Then you can take off
the glass panel.
frontglasspanel.
Now you can start to decorate your fireplace
Your fireplaceshippedwith thefollowingmedia:
3bags ofsableglass and an11piecelogset.
Customerscandecoratetheirfireplace
accordingto their wisheswith supplied media.
This fireplaceincludesthefollowingdecorative
media:

10
OPERATION
Thefireplacecanbeoperatedeitherbytheswitcheslocatedontheleftfront ofthefireplaceunitor
bysupplied remotecontrol.
MANUAL OPERATION
Pushtoreveal themanual controlpanel.(As showsin bellowpicture)
Push here to open the manual control panel
1、 Press key . Press for the first time，heater work at 1900W, indicator ights red.
Press for the second time, heater work at 950W，indicator ights b ue. Press for the
third time, the heating e ement turns off, indicator extinguishes.
Note: after the heating e ements are turned on manua y, the heating e ements work but
are not contro ed by the temperature sensor.
2、Press key . Press for the first time and the charcoa and f ame is in the highest
brightness. Press for the second time ,the charcoa and f ame is in medium brightness.
Press for the third time ,the charcoa and f ame is in ow brightness. Press for the fourth time ,
the charcoa and f ame goes out. Then it circu ates in turn.

11
REMOTE CONTROL OPERATION
1 、 Press the remote contro ’s key“ ”, its screen turns on, the f ame ignites and the f ame icon appears on
the LCD screen of the remote contro . Week, time (24h system), and temperature setting are disp ayed
norma y. Press it again, the screen of the remote contro wi turn off;
2
、 Key“ ”, f ame and charcoa contro switch. In case of ON, press once, the f ame and the charcoa bed
go out, the LCD screen does not disp ay . Press it again and the f ame and the charcoa bed turn on,
the LCD screen disp ays . The buzzer beeps once when the key is pressed;
3
、 Press“ (1) ”to adjust the red f ame. The buzzer beeps once when the key is pressed;
4 、 Press“ (2) ” to adjust the ye ow f ame. The buzzer beeps once when the key is pressed;
5
、 Press“ (3) ” to adjust the b ue f ame. The buzzer beeps once when the key is pressed;
6 、 Press“ ”to turn on, turn off and adjust top ight co ors. The buzzer beeps once when the key is pressed;
1
2
3

12
7、Press the heating key“ .” Press for the first time ,the heating e ements work at 1900W,
the LCD screen disp ays , the indicator on the machine ights red. Press a second
time , the heating e ements work at 950W, the LCD screen disp ays , the indicator
on the machine ights b ue. Press a third time and the heating e ements turn off, the LCD
screen does not disp ay the function icon, the indicator on the machine goes off. The
buzzer beeps once when the key is pressed;
Note: in case the heating e ements are turned on by remote contro , whether the heating
e ements work or not depends on the temperature setting and ambient temperature. They
work on y when the temperature setting is above the ambient temperature.
8、Press key“ ”“ ” to adjust the temperature setting between 7 and 30 ℃ . The
buzzer beeps when the key is pressed;
9、Press shift key“ ”. Press once, the corresponding figure f ashes. Press “ ” “
”
now to set current time and week. The buzzer does not beep when the key is pressed;
10、Press timing parameter setting key“ .” Press for the first time and the LCD screen
disp ays to indicate Monday. Now the temperature setting f ashes, press “ ” to
set the timing temperature for Monday, press key “ ” to confirm and then press “ ”
the time setting for timing.. The disp ayed time parameter is “00-23.” Press “ ”
to set the current operating state of timing function; indicates that the timing is on
current y and the contro temperature is the temperature setting, indicates that the
timing is on current y and the contro temperature is the temperature setting minus 3 ℃, No
disp ay indicates timing is off current and the heating e ements do not work. Corresponding
point f ashes when setting. Press for the second time, it disp ays , set the parameters

for Tuesday. Press for the 7th time and it disp ays . Press for the 8th time and it exits
and recovers to the current week day;
11、Press“ .” Press for the first time and the timing function turns on, the LCD screen
disp ays
, the machine’s indicator ights green. Press again to turn off, icon
on the LCD screen goes off. After the timing function is turned on, it works according
the parameter settings. The LCD screen
ights up according to corresponding parameter settings;
Note: when the time, week and timing parameters are changed, you need to switch on-off
the timing key to transfer the timing parameters to the machine. After the machine has
received them correct y, the buzzer wi beep once.
12、 Press“ ”. Press once to turn on the Open Window function, the LCD screen disp ays
icon , the indicator on the machine ights ye ow. Press again to turn it off, the LCD
screen does not disp ay icon
and the indicator on the machine goes off. The
buzzer beeps when the key is pressed;
After the Open Window function is turned on, the program first y detects if the heating
function is turned on. If it is turned on, the program wi save the current ambient temperature
va ue and detects the ambient temperature change once per 12 minutes. When the
decrease in the ambient temperature detected within 30 minutes exceeds 4 ℃ ,the
program wi deem that the window is open and stop heating, and the Open Window
indicator on the machine wi f ash rapid y. After it has stopped heating for 70 minutes,
the program starts to detect if the window is c osed, and the indicator f ashes s ow y. It
heats for 6 minutes every 30 minutes (position H2). If the temperature rise is more than 2 ℃ ,
the window is considered as c osed, and the indicator stops f ashing.
13

CARE AND MAINTENANCE
CAUTION: Do not use harsh detergents, chemical cleaners or solvents as they may damage the
surface finish of the plastic components.
CONFORMITY WITH DIRECTIVES
Conforms to all relevant European directives
ENVIRONMENTAL PROTECTION
Recycling
This symbol is known as the 'Crossed-out Wheelie Bin Symbol'. When
this symbol is marked on a product or battery, it means that it should not
be disposed of with your general household waste. Some chemicals
contained within electrical/electronic products or batteries can be harmful
to health and the environment.
Only dispose of electrical/electronic/battery items in separate collection
schemes, which cater for the recovery and recycling of materials contained
within. Your co-operation is vital to ensure the success of these schemes
and for the protection of the environment.
1. Switch off and unplug from the power supply before cleaning.
2. Using a soft, moist cloth, with or without a mild soap solution, carefully clean the exterior surface
of the products.
CAUTION: Allow the product to completely cool before handling or cleaning it.
3. Do not allow water or other liquids to run into the interior of the product, as this could create a
fire and/or electrical hazard.
4. We also recommend the periodic cleaning of this appliance by lightly running a vacuum cleaner
nozzle over the guards to remove any dust or dirt that may have accumulated inside or on the
unit.
14

15
REPLACEMENTPARTS
Thislist containsreplacement parts
NO. PARTNUMBER DESCRIPTION QTY.
1 10701213 FRONTCLEARGLASS(MIDDLE) 1
2 10701214 FRONTCLEARGLASS(SIDES) 2
3 10702166 BOTTOMGLASS 1
4 BACKBLACKPLASTICGLASS 1
5 10104002 SWITCH 1
6 FLICKERASSEMBLY 2
7 10101221C FLAMEMOTOR 2
8 601137B LEDSTRIPFORTRAY 1
9 601136B LEDSTRIPFORFLAME 2
10 3001506B REMOTERECIVER 1
11 602032B BLOWERANDHEATERASSEMBLY 1
12 601095F CIRCUITBOARD 1
13 601035 MANUALCONTROL1
14 TOPLIGHT 1
15 10105200 REMOTE 1
3126010
3126512
10125025

16
EXPLODEDVIEW

Wiring Diagram
17

18
TROUBLESHOOTING
PROBLEMPOSSIBLECAUSE SOLUTION
FlameLEDsareburntout InspecttheLEDsand replacethemif
necessary.
Dim orno flame
Backblackcloth is fallingoff
and rolled up in the flicker Changea flicker and back black cloth.
Emberbedis not
glowingordimming EmberLEDsare burnt out InspecttheemberbedLED sand replacethemifnecessary.
Appliancehasoverheatedand
safetydevicehascausedthe
thermal switchtodisconnect
Turnoffthemainswitch,allow
appliancetocoolfor10minutes, then
turn iton.
Housecircuitbreakerhas
tripped Reset housecircuitbreaker.
Applianceturnsoffand
will not turnon
Appliancesfusehasblown Replacethefuse.
Applianceis notpluggedintoan
electrical outlet Checkplugandplugin.
Appliancehasoverheatedand
safetydevicehascausedthe
thermal switchtodisconnect
Turnoffthemainswitch,allow
appliancetocoolfor10minutes, then
turn iton.
Appliancewill notcome
onwhenswitchis
flipped to ON
Circuitboardis burntout Inspectthecircuitboardandreplace
it ifnecessary.
No warmaircomingout
of appliance Heateris burnt out Inspecttheburnerand heater assemblyandreplaceitif necessary.
Flamesputters
Flamemotoris defective. Call aqualifiedservicetechnicianand replaceflamemotor.
RemoteControldoes
not work. Lowbatteries. Unitswitch in “O”position. ReplaceAAA batteriesinremote control.
Turn theswitchin “I”position.
Flameis fixed. Wiringmaybelooseorthe
flamemotormaybedefective.

19
SERVICE HISTORY
This heatermustbeserviced annuallydependingonusage.
DateDealer
Name Servicetechnician Name ServicePerformed Special Concerns
NOTES:

20