Amantii SYM-B Series Installation and maintenance instructions

Fix your Fireplace
SYM-B Series

Content
•How to replace LED light
•How to replace flicker motor
•How to replace heating element
•How to replace the PCB board
•How to replace the signal receiver

SAFETY FIRST
TO AVOID ANY ELECTRICAL SHOCK OR POTENTIAL
DAMAGE TO THE UNIT REMEMBER TO TURN THE
POWER OFF TO THE UNIT BEFORE ATTEMPTING TO
REMOVE OR INSTALL ANY PARTS.

Replace LED light
Step 1
Replace ember bed LED light
Unscrew the 4 screws circled in red to remove the trim.

Magnetic stone
Trim
Please note The bottom of the trim is secured to the face by a magnetic stone.

Step 2 After the trim’s been removed, take off the front glass panel.
Front glass panel

Step 3
The side steel panels need to be removed. To remove the side panels, unscrew
the 4screws circled in red.
The steel panels

Step 4
After the steel panels have been removed, the ember bed glass panel can
carefully be removed by rising one end up first and then out. The ember bed LED
strips are located below it. Remember this is a piece of glass and can break if not
handled with care.

Step 5
The LED strips are held in place with screws and are connected to the other
strips or to the end using a molex connector. Unscrew the screws of the failed
LED strip and unplug the molex connector to replace it with a new one.
Unscrew
Unplug

Replace Flame LED light
Follow STEP 1 to 4 in Replace Ember Bed LED light
Step 1 Remove the back glass to expose location of the flame LED. Unscrew
the screws circled in red to remove the steel bar that secures the back
glass. Remove steal bar and set aside. The back glass can now be
removed and set aside.

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.

Once the panel has been removed you have exposed the location of
the Flame LED strip. They are set back from the Ember bed LED as
seen below
Horizontal view
Bird’s eye view
LED strips for flame
effect lie here

HOOK
BUCKLE
The Flame LED strip is connected using a molex connector and secured
in place with plastic hooks. Disconnect the strip from the molex connector
and carefully unsecure the hooks holding the strip in place. A new strip can
now be installed by reconnecting to the molex connector and secured to
the unit using the hooks.
Step 3

Follow STEP 1 to 4 in Replace Ember Bed LED light
Step 1
Replace flicker motor
Remove the back glass to expose location of the Flicker motor.
Unscrew the screws circled in red to remove the steel bar that
secures the back glass. Remove steal bar and set aside. The back
glass can now be removed and set aside.

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.

Once the flame effect steel panel’s been removed, you can locate the flame motor
on the left side of the unit.

Step 1 Step 2 Step 3
Unscrew the clamp
that secures the
flicker rod onto the
motor. Remove the
rod by carefully
pulling it off of the
motor
Unscrew the 2
screws circled in red
to remove the motor
from the fireplace.
The motor is
connected using
spade connectors.
Carefully disconnect
the motor and replace
Steps to remove Flicker Motor

Follow STEP 1 to 4 in Replace Ember Bed LED light.
Step 1 Remove the back glass to expose the flame effect steel panel.
Unscrew the screws circled in red to remove the steel bar that secures
the back glass. Remove steal bar and set aside. The back glass can
now be removed and set aside.
Replace the heating element

Zoomed View Zoomed View
Step 2
Remove flame effect steel panel. To remove the panel,
remove the 2 screws shown circled in red on each side
of the unit. Remove the panel and set aside.

Remove the screws circled in red located at the top rear of the
inner firebox
Step 3