Amantii Symmetry Bespoke Operating instructions

Symmetry Bespoke
Repair Manual
Revised - 09.26.21

SAFETY FIRST
TO AVOID ANY ELECTRICAL SHOCK OR POTENTIAL
DAMAGE TO THE UNIT REMEMBER TO TURN THE
POWER OFF TO THE UNIT BEFORE ATTEMPTING TO
REMOVE OR INSTALL ANY PARTS.

Table of Content
•How to replace LED light
•How to replace flicker motor
•How to replace heating element
•How to replace the circuit board
•How to replace the AC adapter
•How to replace the canopy light

Replacing the LED lights
Step 1
Replacing the ember bed LED lights
Remove Trim - remove the screws circled in red to safely
remove the trim. Screws will be needed to reinstall the trim.

Magnetic stone
Trim
Please note that there are magnetic stones on the bottom of the fireplace
that attaches the trim to hold the bottom face in place.

Step 2 After the trim has been removed, the front glass panel can be removed.
Front glass panel

Step 3
Remove steel side panels. The steel side panels hold the log in place.
Remove the 4 screws circled in red to remove the side panels. Screws will be
reused to reattach the steel side panels. The media now be removed from
the unit once the side panels have been removed.
The steel panels

Step 4
After the steel panels have been removed, the ember bed glass panel can
carefully be removed by lifting one end up and then out. The ember bed
LED strips are located below it. Please handle the piece of glass with care
to avoid damage to the glass.

Step 5
The LED strips are held in place with screws and are connected to the other
strips or to the end using a molex connector. Unscrew the screws of the failed
LED strip and unplug the molex connector to replace it with a new one.
Unscrew Unplug
Unplug

Replacing the Flame LED light
Follow STEP 1 to 4 from Replacing the Ember Bed LED light.
Step 1 Remove the screws circled in red to remove the steel bar used to hold the
flame effect glass to the unit. Remove steel bar from unit. The flame effect
glass can now be removed from the unit.
steel bar
flame effect glass

Step 2 Removing the flame effect steel panel. To remove the panel
remove the screws circled in red on the unit, as shown in the
diagram. Remove the panel and set aside.
Zoomed View Zoomed View
Zoomed View

After the flame effect steel panel has been removed, the unit should be as shown in
the diagram
LED strips for
flame effect lie
here
The Flame LED strips are held in place with screws and are connected
to the other strips or to the end using a molex connector. Unscrew the
screws of the failed LED strip and unplug the molex connector to
replace it with a new one.
Step 3

Follow STEP 1 to 2 in Replace Flame LED light, you come to here. After the
flame effect steel panel’s been removed, you can see the flame motor on the
left end.
Replacing the flicker motor

Step 1 Step 2 Step 3
Remove the reflector
from the fireplace
Remove the 2
screws circled in red
to remove the motor
from the fireplace.
The motor is
connected using
spade connectors.
Carefully disconnect
the motor and replace.
Steps to remove Flicker Motor

Step 1
Replacing the heating element
Follow STEP 1 in Replace Flame LED light.
Remove the screws circled in red to take off the inner top
panel. The heating element, circuit board, canopy light and
signal receiver are all located here.

INNER TOP PANEL
CIRCUIT BOARD
HEATING ELEMENT
AC ADAPTER

Remove the screws circled in red to take off heating
assembly from the inner top panel.
Step 2

Remove heater brackets from the heater by removing the screws
circled in red. Unplug the heater and replace it with a new heater.
Step 3

Follow STEP 1 in Replace the heating element.
Replacing the circuit board
INNER TOP PANEL
CIRCUIT BOARD
HEATING ELEMENT
AC ADAPTER

Remove the 4 screws circled in red and replace the failed
circuit board with a new one. Secure the new board to the
inner top using the same 4 screws previously removed
Step 1