Amantii WM-BI-26-3623 User manual

INSTALLATION AND
OPERATION INSTRUCTIONS FOR
WALL- MOUNT AND BUILT- IN UNITS
09 13-01
WM-BI-26-3623 WM-BI-26-3623-WHTGLS
WM-BI-34-4423 WM-BI-34-4423-WHTGLS
WM-BI-48-5823 WM-BI-48-5823-WHTGLS
WM-BI-72-8123 WM-BI-72-8123-WHTGLS
WM-BI-FI-34-4423-BLKGLS WM-BI-FI-48-5823-BLKGLS
operation

2
TABLEOF CONTENTS
CONGRATULATIONS!
In selecting this Amantii Wall Mount OR Built-in electric fireplace, you have chosen the
finest and most dependable fireplace on the market today. A beautiful and functional
addition to the finest homes. Welcome to the family of satisfied Amantii electric fireplace
owners.
Please read and carefully follow all of the instruction sfound in this manual. Please pay
special attention to the safety instructions provided in this manual. The instructions
included here will as sure that you have many years of dependable and enjoyable service
from your Amantii product.
Important instructions Page 3
WM-BI-26-3623-/WHTGLS Page 4
WM-BI-34-4423-/WHTGLS Page 5
WM-BI-48-5823-/WHTGLS Page 6
WM-BI-72-8123-/WHTGLS Page 7
Page 8
Installation Overview
Page 9
Package Contents
Page 10
Built-In Installation
Page 12
Wall Mount Installation
Page 13
Fire Glass Media Installation
Page 15
Front Installation
Page 16
Operating the Unit
Page 20
Replacing The Remote Control Battery
Page 21
Care And Maintenance
Page 22
Fireplace Maintenance
Page 23
Trouble Shooting
Page 25
Service History
Page 26
Warranty
Dealer Contact Information Back Page
Page 14
Media options
(WM-BI-FI-34-4423-BLKGLS)
(WM-BI-FI-48-5823-BLKGLS)
Page 24
Parts list

IMPORTANTINSTRUCTIONS
WARNING!
SAVE THESE INSTRUCTIONS
B
A
CD
Fig. 1
Grounding Pin
Cover Of Grounded
Outlet Box
Metal
Screws
Adapter
Grounding
Means Grounding
Pin
15.
5. Do not use outdoors.
3
properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

27” 22” or 68.60 cm 55.9 cm
55.68 lbs or 25.31kg
1500W
19W
6 1/8” or 15.5 cm
25 1/2” or 64.9 cm
21 1/8” or 53.6 cm
25W
sideLeft
t
Appliance Width
750W
1500W
12A
WM-BI-26-3623
WM-BI-26-3623-/WHTGLS
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence oflocal codes,
us the current CSA C22.1 Canadian Elec-
trical Code in Canada or the ANSI/NFPA
States.
120V AC,60Hz
Model Number
Voltage
Amps
Appliance Heigh
Appliance Depth
Gross Weight
Cord Length
Rough Wall Opening Size
74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
MOTOR HEATER
MOTOR FLAME 4W
This appliance has been tested in accor-
dance with the UL Standand 2021 for
appliances in the United States and Cana-
da. If you need assistance during installa-
23
10
21 1/8
1/2
23 1/2
35 1/2
25 1/2
-/WHTGLS
Built-In or Wall Mount Appliance
6 3/4
4

35” 22“ or 88.9 cm 55.9 cm
65.78 lbs or 29.90kg
33 1/2” or 852 cm
WM-BI-34-4423
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence oflocal codes,
us the current CSA C22.1 Canadian Elec-
trical Code in Canada or the ANSI/NFPA
States.
This appliance has been tested in accor-
dance with the UL Standand 2021 for
appliances in the United States and Cana-
da. If you need assistance during installa-
1500W
19W
6 1/8” or 15.5 cm
21 1/8” or 53.6 cm
25W
sideLeft
t
Appliance Width
750W
1500W
12A
120V AC,60Hz
Model Number
Voltage
Amps
Appliance Heigh
Appliance Depth
Gross Weight
Cord Length
Rough Wall Opening Size
74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
MOTOR HEATER
MOTOR FLAME 4W
WM-BI-FI-34-4423-BLKGLS
6 3/4
33 1/2
43 1/2
31 1/2
21 1/8
1/2
10
23
-/WHTGLS
Built-In or Wall Mount Appliance
5
WM-BI-34-4423-/WHTGLS

49” 22“ or 124.46 cm 55.9 cm
82.17 lbs or 37.35kg
47 1/2” or 120.6 cm
WM-BI-48-5823
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence oflocal codes,
us the current CSA C22.1 Canadian Elec-
trical Code in Canada or the ANSI/NFPA
States.
This appliance has been tested in accor-
dance with the UL Standand 2021 for
appliances in the United States and Cana-
da. If you need assistance during installa-
1500W
19W
6 1/8” or 15.5 cm
21 1/8” or 53.6 cm
25W
sideLeft
t
Appliance Width
750W
1500W
12A
120V AC,60Hz
Model Number
Voltage
Amps
Appliance Heigh
Appliance Depth
Gross Weight
Cord Length
Rough Wall Opening Size
74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
MOTOR HEATER
MOTOR FLAME 4W
21 1/8
1/2
23
10
45 1/2
57 1/2
47 1/2
6 3/4
WM-BI-FI-48-5823-BLKGLS
-/WHTGLS
Built-In or Wall Mount Appliance
6
WM-BI-48-5823-/WHTGLS

72 1/2” 22“ or 184 cm 55.9 cm
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence oflocal codes,
us the current CSA C22.1 Canadian Elec-
trical Code in Canada or the ANSI/NFPA
States.
This appliance has been tested in accor-
dance with the UL Standand 2021 for
appliances in the United States and Cana-
da. If you need assistance during installa-
133.12 lbs or 52.41kg
71” or 180.4 cm
WM-BI-72-8123
1500W
19W
6 1/8” or 15.5 cm
21 1/8” or 53.6 cm
25W
sideLeft
t
Appliance Width
750W
1500W
12A
120V AC,60Hz
Model Number
Voltage
Amps
Appliance Heigh
Appliance Depth
Gross Weight
Cord Length
Rough Wall Opening Size
74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
MOTOR HEATER
MOTOR FLAME 4W
WM-BI-72-8123-/WHTGLS
69
81
71
6 3/4
10
21 1/8
23
1/2
-/WHTGLS
Built-In or Wall Mount Appliance
7

i
INSTALLATION OVERVIEW
NOTE: BEFORE YOU INSTALL
SITE SELECTION
wall.
Review and consider all of the following condi-
r r wo (2) wall
ethods:
t-In (page 10)
Wnt (Page 12)
re the power cordis so
pinched or againstasharp edge
and power cordis stored
or redto avoid tripping or snagging
ry to persons.
st c with local codes
-
ry to persons.
rapes, pillow -
re etc.
dir ht and away fr overhead light-
ing.
electric et for ease of electric
and all hardware fr ox and r oveall
packaging relat aterials prior to installa-
WARNING:
T
Phillip rewdriver
aw and/ aw
Level
Tape
Pliers
re
Gloves
E
Fr aterials
Wall Finishing Mar-
terials
aterials
stable)
TOOLS & BUILDINGSUPPLIES
NORMALLY REQUIRED
Volt cir r red.
cated cir referr -
Power supply Wire Gage
Voltage Wire Gage Fuse
120 v 14 G . 15 MP
Wall switch / t hermostat Wire Gage
Voltage Wire Gage
5 Volts 18 Gage
PACKAGING LIST
with:
r te control
To reduce the risk of fire, do not store or
use gasoline or other flammable vapors
and liquids in the vicinity of the heater.
not installed
that it is
ensure that the
Decorative media (See page 13)
8

PACKAGE CONTENTS
A
E
BC
D
Part
1ss
alGA
B1
C Wall Mount Bracket 1
D1
EDecorative Media 1
CONTENTS
Part Description Quantity Picture
Screw
0.16 in. x 1.0 in.
Wall Plug
0.3 in. x 1.5 in.
20
20
B
A
0.16 in. x 0.6 in. 18
CWood Screw
9

NEW CONSTRUCTION OR
RENOVATION
CAUTION:
Two people may be needed to
moisture and is locatedat least 0.91 m or
-
als such as curtains or drapes, furniture,
bedding, paper,etc.
2. Place the appliance in selected loca-
and store appliance in a safe, dry and
4. Prepare a wall with a framed open-
ing to accomodate the size of your unit.
Leave at least 1/4” (6mm) around the
edge of the appliance. Any new wiring
must be done in compliance with local
and nationalcodesand other applicable
outlets or circuits. To reduce the risk
licensed electrician.
WARNING:
To preventcontactwith sagging or
-
ancemust notbe installedagainst
result.
WARNING:
Sides ---------------------- 2 in / 5 cm
Floor ---------------------- 13 3/4 in / 35 cm
Top ---------------------- 2 in / 5 cm
Back ----------------------1/4 in / 0.6 cm
min. 5 cm
2 in
min. 5 cm
2 in
min. 35 cm
13 3/4 in
WALL
FLOOR
10

FIREPLACEINSTALLATIONBUILT IN
k r ow
w
NOTE BEFORE YOUINSTALL
Wall
21
4" [58mm]
Units (models listed in table below) must
stick out of the wall a minimum of
2 1/4" or 5.8 cm
W
D
H
W(") D(") H(")
WM-BI-26-3623 27 5 22
WM-BI-34-4423 35 5 22
WM-BI-48-5823 49 5 22
WM-BI-72-812372 1/2 5 22
The rough wall opening size of the fireplace.
11
-
and the wall studs.

the bottom of unit.
4. Drive mounting screws into the mounting bracket on
Floor
It is strongly recommended that the screws be
screwed into the wall studs where possible. If
anchors are used.
ke sure it is level.
hanging into the keyholes on the back of the unit.
3. Check the appliance for stability ensuring that
the appliance will not pull free from the wall.
NOTE: BEFORE YOU INSTALLStakes for hanging
wall bracket
Back of unit
Stakes for hanging
Side view
Wall
13 3/4 inch
12

Media opons
Models WB-BI-26-3623, WM-BI-34-4423, WM-BI-48-5823, WM-BI-72-8123, are shipped with an LED ember
log that is pre-installed. 3 colours of fire glass media are also included.
See page 16 for log removal instrucons.
See page 16 for media installaon instrucons.
Models WB-BI-26-3623-WHTGLS, WM-BI-34-4423-WHTGLS,
WM-BI-48-5823-WHTGLS, WM-BI-72-8123-WHTGLS,
diamond shaped media.
See page 16 for media installaon instrucons.
Clear
Glass nuggets, clear and
blue diamond shaped media
Harvest Moon Sun Tea LED log
13
WM-BI-FI-34-4423-BLKGLS, WM-BI-FI-48-5823-BLKGLS
are shipped with 3 large glass nuggets, clear and blue

Fire Glass Media - Log Installaon
1. Removing the log
Unplug the unit from wall and make sure controls are switched off. The LED log is shipped in place. The log has
tabs on each side that hold it secure. Remove the side panel to remove the log set and the LED strip.
. Installing the fire glass media
Pour the fire glass media into the tray as shown below. Fee free to use any combinaon of fire glass media that
you find most appealing.
14
2

ear sa
NOTE: BEFORE YOU INSTALL
FRONT INSTALLATION
It is recommended that two people install the
front onto the appliance, w fety glasses and
gloves when handling glass.
appliance body
Wall
Unit
Shoulder Screw
Wall
Mount
Unit
Shoulder Screw
Screw
NOTE: Before you lift the front glass. Unscrew
two screws on both side of the fireplace as
below shown.
1.Lift fireplace front and line up the brackets
with the four (4) shoulder screws on the side of
15

Fix plate
3. Put the plate back and screw back.
appliance directly to the house hold wiring.
electrician may remove the cord connection, and wire the
If it is necessary to hard wire this appliance, a qualified
HARD-WIRE INSTALLATION
OPERATINGTHEUNIT
1. Make sure the appliance is switched OFF (refer
on the right hand side of the unit.
3. Plug unit into electrical outlet.
Wall
outlets or circuits. To reduce the risk of
licensed electrician.
WARNING:
Power adaptor port
Appliance has overheated and safety
device has cause the thermal switch to
discount. Unplug the appliance, allow
appliance to cool for 15 minutes, then
plug back in.
Inspect for an objects on or adjacent to
the heater that may have locked the
airflow or otherwise caused high
temperatures to have occurred.
plate and the power cord fix piece, remove power cord.
Remove the knockout.
2. Attach the wiring to the junction block
1. Unscrew two screw show in the below. Remove the cover
19
16

When using remote control, always point it at the middle of the fireplace, and keep not far away
and “ O ” indicates OFF. When the unit is turned on, there will be chiming sound.
Plug the fireplace in and turn the power switch to “ I “ to turn the power on. The “ I ” indicates ON
OPERATING THE UNIT
than 6 metres.
NOTE: The power switch is located at the bottom left hand side of the unit.
17
This remote control will be used on :
WM-BI-26-3623, WM-BI-34-4423 , WM-BI-48-5823, WM-BI-72-8123
The button located at the top position of the remote control is ON/OFF. Press it, the flame and
ember will be on. The heater will be off. Press again, the fireplace will turn off.
“DISPLAY ON/OFF”: Switching the fireplace flame and tray light ON/OFF. It has functions of setting
memory.
“FLAME ORANGE”: Adjust the orange colour brightness of flame.
“FLAME YELLOW”: Adjust the yellow colour brightness of flame.
“TRAY ORANGE”: Adjust the orange colour brightness of tray.
TRAY WHITE”: Adjust the white colour brightness of tray.
“MOOD LIGHT ON/OFF”: Switching the fireplace mood light ON/OFF.
“ADJUST”: Switching the color of mood light. There are 16
different colors.
“FLASH”: Switching flash kind of mood light. There are 4 different
flash styles.
“HEATER ON/OFF”: Switching the fireplace heater ON/OFF. It
has functions of setting memory.
“HIGH”: The heater works at 1500W.
“LOW”: The heater works at 750W.
“T E M P. ”: The heater keep working if the room temperature lower
than 22℃. The heater not working if the room temperature
higher than 25℃.
“

This remote control will be used on :
18
WM-BI-72-8123-WHTGLS, WM-BI-FI-34-4423-BLKGLS, WM-BI-FI-48-5823-BLKGLS
WM-BI-26-3623-WHTGLS, WM-BI-34-4423-WHTGLS, WM-BI-48-5823-WHTGLS
The button located at the top position of the remote control is ON/OFF. Press it, the flame and
ember will be on. The heater will be off. Press again, the fireplace will turn off.
“DISPLAY ON/OFF”: Switching the fireplace flame and tray light ON/OFF. It has functions of setting
memory.
“DISPLAY ORANGE ”: Adjust the orange colour brightness of flame.
“DISPLAY BLUE ”: Adjust the blue colour brightness of flame.
“MOOD LIGHT ON/OFF”: Switching the fireplace mood light ON/OFF.
“ADJUST”: Switching the color of mood light. There are 16
different colors.
“FLASH”: Switching flash kind of mood light. There are 4 different
flash styles.
“HEATER ON/OFF”: Switching the fireplace heater ON/OFF. It
has functions of setting memory.
“HIGH”: The heater works at 1500W.
“LOW”: The heater works at 750W.
“T E M P. ”: The heater keep working if the room temperature lower
than 22℃. The heater not working if the room temperature
higher than 25℃.
ORANGE BLUE
DISPLAY
HIGH LOW TEMP.
HEATER ON/OFF
DISPLAY ON/OFF
MOOD LIGHT
ON/OFF
ADJUST FLASH

19
B: Main Unit Buttons Operations
1. Power ON/OFF Switch
2. Flame & Ember
3. Mood Light
4. HEAT
5. Indicator
Plug the heater into a suitable outlet.
Set this switch to position I to turn the product ON. Setting it to Oto turn the product OFF. The
POWER LED will be lit when the fireplace insert is on.
Press the HEAT button repeatedly to set the heater to the desired heat setting. The HEATER LED will
indicate the current setting for the heater as shown below:
HEATER LED = Red = 1500W HEAT OUTPUT
HEATER LED = Blue = 750W HEAT OUTPUT
HEATER LED = Purple = AUTO MODE
Auto Mode
In this mode the heater will automatically turn on and off. When the room temperature drops below
71° F. (22° C) the heater will turn on to the high heat setting (1500 watt). When the room temperature
is between 71° and 77° F (22-25° C) the heater output will switch to low heat setting (750W). When the
room temperature goes above 77° F (25° C) the heater will turn off.
1 2 3 4 5
1) "Power ON/OFF"
Press the FLAME&EMBER button to adjust the flame height and ember bed brightness. Press
and release the FLAME&EMBER button to cycle through LO, MED, HI and OFF.
Press the MOOD LIGHT button to change the colour of background light or to flash.
2) "Flame & Ember"
33) "Mode Light"
4) "HEAT"

REPLACING THE REMOTE CONTROL BATTERY
When the remote control stops operating or its range seems reduced, it is time to replace the batteries
with new ones. Remove the batteries if the remote control won’t be used for a long period of time.
1. The battery compartment is located on the back end of the remote.
2. Press the small tab inward as you slide the battery door open and remove the old batteries.
3. Replace with (2) AAA batteries (not included), making sure the + and - sides of the battery match the
inside of the battery compartment.
4. Replace the battery door.
CAUTION:
Always purchase the correct size and grade of battery most suitable for the intended use.
y.
Note:
Caution for Ingestion.
Batteries may contain hazardous substances which could be endangering to the
enviroment and to human health.
This symbol marked on the battery and/or packaging indicates that used battery shall
not be treated as municipal waste. Instead it shall be left at the appropriate collection
point for recycling.
By ensuring used batteries are disposed of correctly, you will help to prevent potential
The recycling of
materials will help to conserve natural resources.
For more information about collection and recycling of used batteries, please contact
your local municipality or your waste disposal service.
Note: please operate remote transmitter at a slow measured pace. Press the remote control buttons with
an even motion and gentle pressure. Repeatedly pressing buttons in rapid succession may cause the
transmitter to Malfunction.
DISPOSAL OF USED BATTERIES
20