Amart Furniture 58135 User manual

ASSEMBLY INSTRUCTION
RYAN STUDY BED
ITEM CODE - 58135
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance
with assembly or for missing parts please phone Amart Furniture, Customer
Service Freecall 1800 351 084.
158135
Furniture

PRE-ASSEMBLY PREPARATION
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
258135
WARNING
To help prevent serious or fatal injuries from entanglement or falls :
* Use the correct size mattress as specified
* Upper surface of mattress must be at least 160mm below upper
edge of guard rails
* Follow all written instructions included with this bed
* Use guardrails on both sides of upper bunk
* Check the bunk bed periodically to ensure that the guardrails,
access device and other components are maintained in the
correct position and state of repair and that all connectors are
tight with nothing protruding more than 8mm
* Ensure the upper bunk is more than 2m from any ceiling fan
* Prohibit horseplay on or under bed
* Prohibit more than one person on the upper bunk
TOP BUNK AND ELEVATED
BEDS ARE DANGEROUS AND
ARE NOT RECOMMENDED
FOR CHILDREN UNDER THE
AGE OF 9.
DO NOT REMOVE THIS LABEL

3
PARTS LIST
7
6
4
5
HB/FB PANEL
HB BED POST LEFT
8
9
10
11
12
13
14
HB BED POST RIGHT
2A
2B
FB BED POST LEFT
FB BED POST RIGHT
3A
3B
HB BOTTOM PANEL
5A
5B
SHORT SAFETY BARRIER
LONG SAFETY BARRIER
BED STORAGE
LADDER POST L/R
LADDER TREAD
METAL SUPPORT RAIL
TABLE SIDE STORAGE
- 18mm x 59mm x 920mm
SIDE RAIL LEFT
SIDE RAIL RIGHT
WITH DRAWER
TABLE TOP
1
2
58135
WOOD SLAT 9pcs / 2 set
NO PART QTY PICTURE PACKING CARTON
3
2 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
1 PC
1 UNIT
2 PCS
3 PCS
1 PC
1 PC
1 UNIT
2 SETS
BOX 1 / 5
BOX 2 / 5
BOX 1 / 5
BOX 3 / 5
BOX 5 / 5
BOX 1 / 5
BOX 3 / 5
BOX 4 / 5
BOX 1 / 5
BOX 3 / 5

4
JCBC SCREW
M6 x 100mm (R/B)
BARREL NUT
WOOD DOWEL
M8 x 30mm
M3.5 x 12mmCSK SCREW
L BRACKET
FLAT WASHER M8 (R/B)
M4 x 30mmCSK SCREW
6 HOLES
JCBC SCREW
M6 x 30mm (R/B)
JCBC SCREW
M6 x 45mm (R/B)
JCN NUT
MINIFIX
ALLEN KEY - M6
58135
METAL BUSHING D30 x T38mm
PIN
BOLT D8 x 85mm
JCBC SCREW
M6 x 40mm (R/B)
BARREL NUT
CASTOR
HARDWARE LIST
J
I
F
K
L
M
N
O
P
Q
A
NO PART QTY PICTURE PACKING CARTON
12 PCS
18 PCS
42 PCS
12 PCS
4 PCS
1 PC
6 PCS
3 PCS
18 PCS
1 PC
1 PC
2 PCS
1 PC
8 PCS
2 PCS
2 PCS
1 PC
BOX 4 / 5
B
C
D
E
G
H
JCBC SCREW
M6 x 80mm (R/B)
BARREL NUT
JCBC SCREW
M6 x 60mm (R/B)
BARREL NUT
RM3.5 x 16mmCSK SCREW 8 PCS
PLASTIC WASHERM6 1 PC
S

JCBC SCREW
M6 x 30mm (R/B)
E - 2 Pcs
558135
PART A
PART B
PART C
JCBC SCREW
M6 x 100mm (R/B)
BARREL NUT
A - 12 Pcs
WOOD DOWEL
M8 x 30mm
C - 30 Pcs
JCBC SCREW
M6 x 80mm (R/B)
BARREL NUT
B - 18 Pcs
M4 x 30mm
CSK SCREW
N - 8 Pcs
JCBC SCREW
M6 x 60mm (R/B)
BARREL NUT
WOOD DOWEL
M8 x 30mm
C - 12 Pcs D - 12 Pcs
JCBC SCREW
M6 x 30mm (R/B)
E - 2 Pcs
JCBC SCREW
M6 x 40mm (R/B)
BARREL NUT
O - 2 Pcs
JCBC SCREW
M6 x 45mm (R/B)
JCN NUT
F - 1 Pc
P - 1 Pc
PLASTIC WASHER
M6
M3.5 x 12mm
CSK SCREW
L BRACKET
MINIFIX
G - 6 Pcs H - 3 Pcs I - 18 Pcs
6 HOLES
METAL BUSHING
D30 x T38mm
PIN
FLAT WASHER
M8 (R/B)
J - 1 Pc K - 1 Pc
L - 2 Pcs M - 1 Pc
BOLT D8 x 85mm
Q - 2 Pcs
CASTOR M3.5 x 16mm
CSK SCREW
R - 8 Pcs

6
1
13B
3A
2B
2A
4
65A
5B
11
12
13
8
9
10
7
14
6
58135
PERSPECTIVE VIEW

7
A
C
A
A
A
C
B
C
B
C
B
B
Step 1 :
Step 2 :
6
4
1
1
3B
2B
2A
3A
5A
5B
Assemble headboard and footboard parts as shown by using JCBC screw 'A' and wood
dowel 'C'.
Fixed side rails '5' and long safety barrier '6' to headboard and footboard by using JCBC
screw 'B' and wood dowel 'C'.
JCBC SCREW
M6 x 100mm (R/B)
BARREL NUT
A - 12 Pcs
JCBC SCREW
M6 x 80mm (R/B)
BARREL NUT
B - 16 Pcs
WOOD DOWEL
M8 x 30mm
C - 12 Pcs
WOOD DOWEL
M8 x 30mm
C - 16 Pcs
58135
ASSEMBLY FOR PART A

5
C
D
D
E
E
Step 3 :
Step 4 :
9
9
10
Assemble bed ladder '9 & 10' by using wood dowel 'C' and JCBC screw 'D'
Attach the bed ladder at footboard side and fixed with JCBC screw 'E'
JCBC SCREW
M6 x 60mm (R/B)
BARREL NUT
WOOD DOWEL
M8 x 30mm
C - 12 Pcs D - 12 Pcs
JCBC SCREW
M6 x 30mm (R/B)
E - 2 Pcs
58135
8
ASSEMBLY FOR PART B

9
B
B
C
O
F
O
Step 5 :
Step 6 :
Fix short safety barrier '7' at end side by using JCBC screw 'B' and wood dowel 'C'.
Fix other end side of safety barrier '7' to the bed ladder with JCBC screw 'O' and JCBC screw
'F' + Plastic washer 'P' + JCN nut 'F'.
7
JCBC SCREW
M6 x 80mm (R/B)
BARREL NUT
B - 2 Pcs
WOOD DOWEL
M8 x 30mm
C - 2 Pcs
JCBC SCREW
M6 x 40mm (R/B)
BARREL NUT
O - 2 Pcs
JCBC SCREW
M6 x 45mm (R/B)
JCN NUT
F - 1 Pc
58135
F
P
P - 1 Pc
PLASTIC WASHER
M6
ASSEMBLY FOR PART A
ASSEMBLY FOR PART B

E
Step 7 :
11
Fix metal support rail '11' with JCBC screw 'E'.
10 58135
ASSEMBLY FOR PART A
JCBC SCREW
M6 x 30mm (R/B)
E - 2 Pcs
ASSEMBLY FOR PART C
Step 8 : Fix table top '13' and table side storage '12' with mini fit 'G' as
shown. Attach L bracket ' H ' with screw ' I ' and than fix the
castor 'Q' with screw 'R' at pre - marking hole as shown.
13
12
M3.5 x 12mm
CSK SCREW
L BRACKET
MINIFIX
G - 6 Pcs H - 3 Pcs I - 18 Pcs Q - 2 Pcs
CASTOR
G
G
H
I
Q
R
6 HOLES M3.5 x 16mm
CSK SCREW
R - 8 Pcs

Step 9 :
Step 10 : Attach wood slat '14' to side rail support and fix with screw 'N' and than fix safety barrier
support '15' with JCBC screw 'E' as shown.
Fix table top to the support rail by using bolt 'J', metal bushing 'K', washer M8 'L', and pin 'M'.
11
METAL BUSHING
D30 x T38mm PIN
FLAT WASHER
M8 (R/B)
J - 1 Pc K - 1 Pc L - 2 Pcs M - 1 Pc
M4 x 30mm
CSK SCREW
N - 8 Pcs
58135
N14
BOLT D8 x 85mm
J
LK
M
ASSEMBLY FOR PART C
ASSEMBLY FOR PART A

Step 11 :
12
ASSEMBLY COMPLETE
58135
Place bed storage with drawer '8' as shown.
8
Note: The bed storage is free standing item and can use in other places.

Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
. Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.
13 58135

NOTE : ATTACMENT ASSEMBLY INSTRACTION AND HARDWARE
FOR ADDITIONAL PARTS OF SAFETY BARRIER SUPPORT.
SAFETY BARRIER SUPPORT
Fix safety barrier support '15' with JCBC screw 'E' as shown.
JCBC SCREW
M6 x 30mm (R/B)
E - 8 Pcs
E
15
QTY : 2 PCS
15
LONG SAFETY BARRIER
WITH SUPPORT HOLE.
6A
LONG SAFETY BARRIER
WITHOUT SUPPORT HOLE.
6B

ASSEMBLY INSTRUCTION
RYAN STUDY BED
ITEM CODE - 58135
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance
with assembly or for missing parts please phone Amart Furniture, Customer
Service Freecall 1800 351 084.
158135
Furniture

PRE-ASSEMBLY PREPARATION
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
258135
WARNING
To help prevent serious or fatal injuries from entanglement or falls :
* Use the correct size mattress as specified
* Upper surface of mattress must be at least 160mm below upper
edge of guard rails
* Follow all written instructions included with this bed
* Use guardrails on both sides of upper bunk
* Check the bunk bed periodically to ensure that the guardrails,
access device and other components are maintained in the
correct position and state of repair and that all connectors are
tight with nothing protruding more than 8mm
* Ensure the upper bunk is more than 2m from any ceiling fan
* Prohibit horseplay on or under bed
* Prohibit more than one person on the upper bunk
TOP BUNK AND ELEVATED
BEDS ARE DANGEROUS AND
ARE NOT RECOMMENDED
FOR CHILDREN UNDER THE
AGE OF 9.
DO NOT REMOVE THIS LABEL

3
PARTS LIST
5
6
TOP PANEL
2
VERTICAL PANEL
DRAWER BOX
4
BIG BACK PANEL
SMALL BACK PANEL
58135
NO PART QTY PICTURE PACKING CARTON
3
2 PCS
1 PC
2 PCS
1 UNIT
1 PC
1 PC
BOX 5 / 5
SIDE PANEL L/R1
WOOD DOWEL M8 x 30mm
HARDWARE LIST
A
NO PART QTY PICTURE PACKING CARTON
14 PCS
12 PCS
8 PCS
20 PCS
B
C
D
JCBC SCREW M6 x 25mm (R/B)
PAN HEAD SCREW #3.5 x 16mm
JCBC W SCREW M6 x 50mm (R/B)
BOX 5 / 5

458135
PERSPECTIVE VIEW
2
5
3
1
4
6
1

558135
WOOD DOWEL
M8 x 30mm
B - 4 Pcs
JCBC W SCREW
M6 x 50mm (R/B)
A - 4 Pcs
Step 1 : Assemble drawer box '4' and vertical panel '3' as show by using JCBC W screw 'A' and wood
dowel 'B'.
A
B3
3
4
WOOD DOWEL
M8 x 30mm
B - 4 Pcs
JCBC W SCREW
M6 x 50mm (R/B)
A - 4 Pcs
Step 2 : Fix top panel '2' to vertical panel '3' by using JCBC W screw 'A' and wood dowel 'B'.
3
B
A
2
3

658135
WOOD DOWEL
M8 x 30mm
B - 4 Pcs
JCBC W SCREW
M6 x 50mm (R/B)
A - 6 Pcs
Step 3 : Fix the side panel L/R '1' to the top panel '2' by using JCBC W screw 'A' and wood dowel 'B'.
1
A
2
B
1
JCBC SCREW
M6 x 25mm (R/B)
C - 8 Pcs
Step 4 : Fix drawer box '4' to the side panel '1' by using JCBC screw 'C' as shown.
1
C
41