Amart Furniture 64086 User manual

ASSEMBLY INSTRUCTION
VIKA GAS LIFT QUEEN BED
ITEM CODE - 64086
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
164086
1622mm
1399mm
2203mm
Furniture
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance
with assembly or for missing parts please phone Amart Furniture, Customer
Service Freecall 1800 351 084.

PRE-ASSEMBLY PREPARATION
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
2
TOOL REQUIRED
64086

3
PARTS LIST
WOOD SLAT
FOOTBOARD
BIG BASE PANEL
SIDE RAIL-R
HEADBOARD FRAME
HEADBOARD PANEL
HEAD POST L/R
SIDE RAIL-L
CENTER WOOD PANEL
SMALL BASE PANEL
1
2
3
4
5
6
7
8
9
10
64086
MINI FIX BOLD
A x 12pcs B x 12pcs
WOOD DOWEL
M8 x 30mm ML-CB (METALCORNER BLOCK)
C x 2pcs
JCBC BOLT
M8 x 35MM
D x 8pcs
JCBC BOLT
M8 x 25MM JCBC BOLT
M8 x 15MM JCBC BOLT
M8 x 20MM JCBC BOLT
M8 X 75MM
FLAT WASHER M8 BASE NUT BASE HANDLE JCBC BOLT
M6 x 40MM
M8 x 45MM JCBB BOLT c/w NUT
c/w HEX NUT,SPRING & FLAT
WASHER
ALLEN KEY - M6
M12.8 SPANAR M14 SPANAR
E x 16pcs F x 8pcs G x 10pcs H x 4pcs
I x 4pcs J x 4pcs K x 3pcs L x 6pcs
M x 6pcs P x 1pc
Q x 1pc R x 1pc S x 1pc
SINGLE END
PLASTIC CAP DOUBLE END
PLASTIC CAP
N x 32pcs O x 16pcs
11
RIGHT HYDRAULIC BASE SUPPORT
12
HYDRAULIC PUMP
13
14 BACK BED BASE
15 FRONT BED BASE
LEFT HYDRAULIC BASE SUPPORT
WITH STOPPER
2
5
8
9
7
4
1
11 13
3
6
12
10
15
14

4
STEP 1: Assemble the bed post L/R '2' to the headboard panel '3' with minifix screws 'A' and wood dowel B' as shown .
2
3B
A
STEP 2: Fix headboard frame '1' and head post L/R with bolts 'D' and allen key 'Q' as shown.
1
D
64086
ALLEN KEY - M8
Q

5
STEP 3: Assemble the left & right side rails '5''6' to the center wood panel '7' with minifix screws 'A' and wood dowel 'B'
as shown.
6
5
7
7
A
B
STEP 4: Fix headboard and footboard '4' with bolts 'E' and allen key 'Q' as shown.
E
E
4
64086
Q
Q

6
STEP 5: Fix metal bracket 'C' to the corner between footboard and side rails with bolts 'F' and allen key 'Q' as shown.
FC
STEP 6: Firstly, fix the hydraulic pump to each hydraulic base as shown in diagram 5.1. Next, fix the left & right hydraulic
support to the both side rails. Then, fix bolts 'G' using allen key 'Q' first as shown in diagram 5.2 and do not tighten yet.
Finally, fix all bolts and tighten as shown in diagram 5.3.
13
11/12
13
13
G
G
12
11
5.1 Hydraulic Pump right installation.
5.2
5.3
64086
Q
Q
Q

STEP 8: Place base panels ' 8 ' & ' 9 ' as shown.
8
9
7
STEP 7: Assemble front & back frames bed base with flat washer M8 'I', base nut 'J' and bolts 'H' using allen key 'Q' and than
fix base handles to the bed base with bolts 'L' using allen key 'P' as shown.
I
HK
L
14
H
I
J
J
64086
15
Q
P
L

864086
STEP 9: Place wood slats with plastic caps as above drawing. Then, fix it on the bed base by pressing it accordingly to the
default holes. Ensure the plastic cap's pin is aimed to the hole.
NN
Each wood slat must be inserted with a single end and double end plastic cap
as shown on the picture.
10 10
O
STEP 10: Assemble the bed base on the right & left hydraulic frame and fix bolts starting from '1' to '3' as shown.
Important note : Do not tighten the bolts yet!
1
2
3
M

ASSEMBLY COMPLETE
964086
STEP 11: Adjust the bed base, make sure distance with the front footboard approximately 15mm to above as shown.
Important Note : Tighten all screws.
15mm to above

10
CAUTION :
PLEASE USE HYDRAULIC PUMP STOPPER FOR SAFETY PURPOSE.
64086