American DJ X-Treme/AS User manual

American DJ®User Instructions
• New ZB-SC150 “Super Color” 150W, 4,000K 6,000Hr lamp
• 9 Dichroic Colors plus White
• 8 Gobos plus Spot on separate wheel
• 360 degree rotation of Gobo and Color Wheels
• DMX-512 Protocol
• Controlled by the X-Treme/19C™ or X-Treme/C™ Basic Controller
X-Treme/AS™ Features
The X-Treme/AS™ intelligent lighting fixture features a long life, extremely bright 150W arcstream lamp, 9 rich dichroic
colors plus white, 8 gobos plus spot, separate gobo/color wheels, and strobes in every color. 360 degree rotation of
gobo & color wheels with speed control provide a X-treme™ lighting show for club, concert, and mobile use. DMX-
512 protocol. Fan cooled. Also available in 220V operation. Controlled by the X-Treme/19C™ or X-Treme/C™. The
X-Treme/19C™: Programmable controller with 64 channel DMX-512 output; Ergonomic joystick control of pan/tilt motion;
56 professionally designed pan/tilt motions; 6 Show memories of 300 steps; Show memories can be chased for long
concerts; Instant manual override and control of all projectors and functions; Built-in gobo & color chases; and Quick,
intuitive modular programming. Control up to 16 heads. 120V or 220V operation. 3 space, 19 in. rack mount. The
X-Treme/C™: A basic controller that operates blackout; built-in programs; gobo/color change;
speed control of gobo/color wheels; and strobing. Control up to 8 heads. 120V or 220V operation.
X-Treme/AS™ Description
Voltage: 120V , 60 Hz
Dimensions: 22.75” x 9” x 6.5” / 740mm x 293mm x 212mm
Lamp: ZB-SC-150, 150W, 4,000K 6,000 hour lamp l
Weight: 27 lbs. / 12.3 kg.
Fuse: 5A
X-Treme/AS™ Specifications
HALOGEN LAMP WARNING!
This fixture is fitted with a halogen lamp
which is highly susceptible to damage if
improperly handled. Never touch lamp
with bare fingers as the oil from your
hands will shorten lamp life. Also, never
move fixture until lamp has had ample
time to cool. Remember, lamps are not
covered under warranty conditions.
Thank you for purchasing this American DJ® product. Some assembly required.
Please read the following instructions before installing or using your new unit.
X-Treme/AS ™
INTELLIGENT LIGHTING FIXTURE
©American DJ® Los Angeles Ca. 90058 - www.americandj.com - X-Treme/AS™ Page 1

Section 1
Inspection
Every X-Treme/AS™ projector was thoroughly tested and shipped in perfect condition. Carefully
unpack the projector and remove the bag with components from the carton. Inspect equipment for
shipping damage.
Packing list:
1. X-Treme/AS™ Projector
2. IEC power cord
3. Operating manual
Lamp Installation
Caution! Extremely hot! Always allow unit to cool before re-lamping
1. Loosen thumbscrews on back of unit. Slide out the lamp holder assembly.
2. Remove lamp from original packaging. Read the enclosed instructions. Lamp is
included with X-Treme/AS™ Projector Do not touch glass with bare hands as this
could damage the lamp.
3. Fit lamp Into holder
4. Slide lamp holder assemble back Into unit.
5. Tighten retaining screws
Projector Installation
1. Unit can be hung In any position.
2. Make sure to use a minimum 35Kg rated clamp.
3. Allow enough space on all sides for proper cooling.
4. Connect IEC power cord to back of unit.
5. Plug cord into property grounded socket.
*Check that the voltage marked on the back of unit is correct for your area.
6. Lamp will light and unit will reset and wait for signal from controller.
*The shutter is closed in stand-by mode, so it will be difficult to tell if the lamp is
lit without a controller.
* Unit may make smoke for a few minute until dust and excess paint is burned off by the lamp.
Precautions:
1.Never operate unit when case is open.
2.Never cover unit as this may block air vents and cause overheating and
possible fire hazard.
3. Never operate unit in the rain or in damp moist conditions as this could
cause electric shock.
4. Follow standard electrical safety precautions when installing, operating or
servicing the unit to prevent electrical shock, fire, or equipment damage.
5.These units are for commercial use and contain no user-serviceable parts inside.
Servicing must be conducted by qualified service personnel.
Getting Started
©American DJ® Los Angeles Ca. 90058 - www.americandj.com - X-Treme/AS™ Page 2

Lens Focusing
1. Hang fixture in its final position
2. Set Function DIP switch #6 to on.
3. Projector shutter will open and Pan and Tilt will be set to center and Gobo will be set to “small
spot”
4. Use a screwdriver to loosen the silver retaining screw .
5. Adjust lens until sharp focus is obtained.
Warning. Tighten screw securely. If screw Is not tight, the lens tube could slide out of the
fixture, causing equipment damage and or personal injury.
Section 2
DMX512 Operation
I. Connect the X-Treme/AS™ fixture to the X-Treme/C™, X-Treme/19C™ or any suitable
DMX-512 controller with a 3 pin XLR data cable.
2. Continue to connect together all the fixtures using 3 pin XLR data cables.
3. Set the DMX address for each fixture using the 9 pin DIP switch on the back panel fixture.
Each fixture uses 4 DMX-512 channels;
CH1: Color, CH2: Gobo 1; CH3: Pan; CH4: Tilt
You must select the proper DMX-512 address for each X-Treme/AS™ projector.
Below Is a chart of standard addressing for use with the X-Treme/C™ ,X-Treme/19C™ controllers.
DIP switch setting
Projector
DIP switch setting
Projector
19
1 2 3 4 5 6 7 8 9
2
1 2 3 4 5 6 7 8 9
10
1 2 3 4 5 6 7 8 9
3
11
1 2 3 4 5 6 7 8 9
412
1 2 3 4 5 6 7 8 9
5
1 2 3 4 5 6 7 8 9
13
614
7 15
816
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9
9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
DMX-512 Addressing
©American DJ® Los Angeles Ca. 90058 - www.americandj.com - X-Treme/AS™ Page 3

These functions are designed to give you added convenience and power, making installation and pro-
gramming faster and easier.
Switch Off On
No. 1 Gobo positions Unlimited Gobo positions
No. 2 No Function No Function
No. 3 Normal Inverted Pan
No. 4 Normal Inverted Tilt
No. 5 Normal Self test
No- 6 Normal Focus
No. 7 Normal Auto Program
No. 8 Normal DMX-512 Termination
Function #1: "Off": Gobo wheel only stops at full and split color positions.
This makes programming and control much easier.
"On": Gobo wheat can be placed In any position for extreme control and special
effects.
Function #2: No Function
Function #3: "On" Inverts the Pan motion. Useful when projectors are mounted "head to head",
to allow the Mirrors to move in unison.
Function #4: "On" Inverts the Tilt motion. Useful when projector are mounted "head to head", to
allow the mirrors to move In unison.
Function #5: "On" X-Treme™ automatically runs through all the features one at a time. So you
can see every gobo and color and pan/tilt motion. Used when testing operation
of unit.
Function #6: "On" Makes focusing the X-Treme/AS™ easy. Opens the shutter and places the
"small spot" Gobo In the center for easy focusing without need of a controller.
Function #7: "On" Built-in demonstration program
Function #8: "On" DMX512 line termination, Used when this is the last projector of the DMX-5I2
chain.
Function Settings
©American DJ® Los Angeles Ca. 90058 - www.americandj.com - X-Treme/AS™ Page 4

Figure 1
XLR MALE SOCKET
1 EARTH Cold 2
3 Hot
XLR FEMALE SOCKET
1 EARTH
Cold 2
3 Hot
Figure 2
XLR Pin Configuration:
Pin 1 = Shield
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
DMX TRAITS
VALUE COLOR - CHANNEL 1 VALUE GOBO - CHANNEL 2
0WHITE
167
160
144
128
112
99
88
77
96
80
64
48
32
16
66
55
44
33
22
11
0
191
220
208
200
164
140
128
179
110
255
232
255
239
227
215
203
BLUE
UV - PURPLE
WHITE
SLOW COLOR SCROLL
FASTER COLOR SCROLL
FASTER COLOR SCROLL
FASTER COLOR SCROLL
FASTER COLOR SCROLL
FASTER COLOR SCROLL
FASTER COLOR SCROLL
FASTEST COLOR SCROLL
RED
MAGENTA
FASTER STROBE
FASTER STROBE
FAST STROBE
SLOW STROBE
FASTEST GOBO SCROLL
FASTER GOBO SCROLL
FAST GOBO SCROLL
SLOW GOBO SCROLL
BLACKOUT
BARS
TUNNEL
STAR
WAVE
BUBBLES
SEGMENTED CIRCLE
MULTI STAR
SMALL SPOT
SHUTTER OPEN - LARGE SPOT
SHUTTER CLOSED
ORANGE
GREEN
CYAN
YELLOW
PINK
VALUEPAN - CHANNEL 3VALUE TILT - CHANNEL 4
0
255
128
255
128
0FULL TOP POSITION
FULL RIGHT POSITION FULL BOTTOM POSITION
MIRROR - CENTER POSITIONMIRROR - CENTER POSITION
FULL LEFT POSITION
Data Cable (DMX Cable) Requirements:
Your fixture and your controller require a standard 3-pin XLR connector for data
input and data output. If you are making you own cables be sure to use standard
two conductor shielded cable (This cable may be purchased at almost all pro
sound and lighting stores). Your cables should be made with a male and female
XLR connector on either end of the cable (see Figure 1). Also remember that
DMX cable must be daisy chained and can not be “Y”ed or split.
Notice: Don not use the ground lug on the XLR connector. Do not connect
the shield conductor to the ground lug or allow the shield conductor to come in
contact with XLR outer casing. Grounding the shield could cause a short circuit
and erratic behavior.
Special Note: For excessive cable runs totaling 100ft. or more, we recom-
mend using a terminator of 80-100 ohms/.5w. Long cable runs can sometimes
cause erratic behavior. Terminators prevent excessive signal loss by mirroring
the signal back through the line, decrease the possibilities of erratic behavior.
©American DJ® Los Angeles Ca. 90058 - www.americandj.com - X-Treme/AS™ Page 5