American Eagle 30P User manual

Model 30P
Single-Stage Piston
Compressor Manual
American Eagle
740 North State Street
PO Box 169
Garner, IA 50438
800-392-3015
www.americaneagleacc.com
Subject to Change without Notification.
© 2019 American Eagle
Rev 1
PN 92582
Specifications • Installation • Assembly
®

Page ii | American Eagle®30P Compressor Manual
Model 30P Manual Revisions
Date of Revision Section Revised Description of Revision
Serial Tag
DATE
HYDRAULIC FLOW (GPM) HYDRAULIC PRESSURE (PSI)COMPRESSOR SPEED (RPM)
HYDRAULIC MOTOR SERIAL
COMPRESSOR MODEL
MADE IN THE U.S.A. BY AMERICAN EAGLE.
COMPRESSOR SERIAL
PATENT INFORMATION
http://www.americaneagleacc.com/ip
PN 54490

American Eagle®30P Compressor Manual | Page iii
Table of Contents
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:
Technical Questions, and Information: [email protected]
Order Parts: [email protected]
Warranty Information: [email protected]
Introduction ............................................................................................................................................iv
Chapter 1 - Specifications......................................................................................................................... 1
Chapter 2 - Installation .............................................................................................................................. 3
Component Installation......................................................................................................................... 3
Component Installation, continued..................................................................................................... 4
30P Electrical Schematic....................................................................................................................... 5
Hydraulic System .................................................................................................................................... 6
Air System ................................................................................................................................................ 6
Compressor Pressure Switch.................................................................................................................. 7
Typical Hydraulic Circuit for Single-Section Pump.............................................................................. 8
Typical Hydraulic Circuit for Tandem (Two Part) Pump .................................................................... 9
Typical Hydraulic Circuit for Compressor with Auxiliary Cooler ...................................................... 10
Chapter 3 - Assembly Drawings ............................................................................................................. 11
30P Case Assembly - PN 66354 ........................................................................................................... 11
30P Assembly Drawing - PN 66338...................................................................................................... 12
SUH-60 Compressor Assembly............................................................................................................. 14
Crankcase Group (Tapered Shaft) .................................................................................................... 15
Crankcase Group (Straight Shaft)...................................................................................................... 16
Cylinder Group..................................................................................................................................... 17
Head Group.......................................................................................................................................... 18
Head Options ....................................................................................................................................... 19
Optional Head Unloader..................................................................................................................... 20
Flywheel Options .................................................................................................................................. 21
Clutch Options ..................................................................................................................................... 22
Chapter 4 - Replacement Parts .............................................................................................................. 23

Page iv | American Eagle®30P Compressor Manual
Introduction
American Eagle®Air Compressors are designed to provide safe and dependable service
for a variety of operations. With proper use and maintenance, these air compressors will
operate at peak performance for many years.
To promote this longevity, carefully study the information contained in this manual before
putting the equipment into service. Though it is not intended to be a training manual for
beginners, this manual should provide solid guidelines for the safe and proper usage of the
air compressor.
Once you feel comfortable with the material contained in this manual, strive to exercise
your knowledge as you safely operate and maintain the air compressor. This process is vital
to the proper use of the unit.
A few notes on this manual:
A copy of this manual is provided with every air compressor and can be found in the hard
plastic manual case that is installed on the chassis. A copy of this manual shall remain with
the air compressor at all times.
Throughout the manual, three signal words will be used to bring attention to important
items:
A NOTICE signal word indicates a practice not related to physical injury.
A WARNING signal word indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
A DANGER signal word indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Information contained within this manual does not cover all maintenance, operating, or
repair instructions pertinent to all possible situations. Please be aware that some sections
of this manual contain information pertaining to American Eagle®manufactured air
compressors in general and may or may not apply to your specific model.
This manual is not binding. American Eagle reserves the right to change, at any time, any
or all of the items, components, and parts deemed necessary for product improvement or
commercial/production purposes. This right is kept with no requirement or obligation for
immediate mandatory updating of this manual.
In closing:
If more information is required or technical assistance is needed, or if you feel that any
part of this manual is unclear or incorrect, please contact the American Eagle Customer
Service Department by phone at 800-392-3015 or email at service@americaneagleacc.
com.
WARNING
NOTICE
DANGER

American Eagle®30P Compressor Manual | Page 1
Chapter 1 - Specifications
20.07
19.68
28.23
4.19
13.00
9.56
6.87 13.00 6.87
.44 X 0.63 SLOT
TYP 12
1.09
17.50
1.09 1.65
3.15
13.38
1.65
3.15
SPECIFICATIONS 30P
Hydraulic System 10-11 GPM @ 1650 PSI
Compressor RPM 1300 RPM
Hydraulic Operating Pressure 1650 PSI
Hydraulic Relief Pressure 3000 PSI
Max Working Pressure 150 PSI
Air Delivery (At Max Speed) 30 CFM @ 100 PSI
Weight (Hydraulic Driven Asm) 225 lbs.
Weight (Air Pump Only) 89 lbs.
Dimensions (Length) 28.25"
Dimensions (Width) 20.13"
Dimensions (Height) 19.75"
Electrical 12V DC
Crankcase Oil Capacity 1 Quart
Cooler Fan 800 CFM, 12 Volt (Pull)
Drive Type Direct Driven
Duty cycle on Piston Compressors is 50:50 over 10 minutes.
NOTICE

Page 2 | American Eagle®30P Compressor Manual
This page intentionally left blank.

American Eagle®30P Compressor Manual | Page 3
Chapter 2 - Installation
Component Installation
This section pertains to the installation of the air compressor, PTO, pump and other related
items. The instructions are intended as a guide to assist you with particular installation.
These instructions will provide only general information.
Compressor Torque Procedure
Head Assembly:
Torque Value: 34 ft-lbs
Procedure: Assemble head on the cylinder with head bolts
started only, not tight. Working in the pattern shown, torque
three times, increasing the torque each time as follows:
First Torque: 10 ft-lbs
Second Torque: 20 ft-lbs
Third Torque: 34 ft-lbs
After five hours of use re-torque bolts to 34 ft-lbs.
Cylinder Assembly:
Torque Value: 20 ft-lbs
Procedure: After assembling cylinder over pistons and setting into place, tighten (6) cap
screws finger tight. In a criss-cross pattern, tighten bolts evenly so all bolts are hand snug.
Again in a criss-cross pattern torque each bolt to 20 ft-lbs, checking each bolt twice. After
five hours of use, re-torque bolts to 20 ft-lbs.
Connecting Rod Control:
Torque Value: 18 ft-lbs
Procedure: Assemble rod onto the crankshaft taking care to align the machined surfaces
together and tighten cap screws finger tight. Tighten bolts until hand tight and torque to 18
ft-lbs. Check twice the torque reading before final assembly of the cylinders.
12
43
56

Page 4 | American Eagle®30P Compressor Manual
Pump Assembly:
The pump assembly may either be installed directly on the PTO or as an optional
method, may be driven by a driveline from the PTO. Pump manufacturers provide specific
installation information for their products and should be consulted if questions arise.
Note: A dual or tandem hydraulic pump is recommended when additional hydraulically
operated equipment are added to the hydraulic system.
PTO Assembly:
Check with the PTO manufacturer’s representative for specific instructions regarding your
particular make, model, and year of vehicle. As some trucks may require modification of
the transmission cross member and the exhaust system, the manufacturer’s instructions
should be followed to ensure proper installation of the PTO.
Compressor Assembly:
Prepare the mounting location of the compressor by locating and drilling four (4) holes,
1/2” diameter as per the mounting pattern of the air compressor base. Using four (4) 3/8” x
1.25 GR-5 cap screws, 3/8” flat washer, and 3/8” nyloc nut, secure the compressor in place.
The compressor is air cooled, and must have a clean supply of cooling air to the fan with
minimum restrictions. Adequate space must be provided for proper circulation of air.
Electric Speed Control:
An optional electric or electronic speed control must be used to maintain proper
operating speed of the air compressor. The engine speed control will automatically
increase from idle to preset speed when engaged and decrease when disengaged.
POWER SUPPLY
(12V BATTERY HOT)
GROUND
CPRSR RELAY
(12V CONTROL INPUT)
SPEED CTRL
(12V CONTROL OUTPUT)
RED 12GA
GRN 14GA
YEL 14GA
BLK 12GA
CIRCUIT BREAKER
(STELLAR SUPPLIED)
BATTERY +
* CUSTOMER ADDED WIRING MUST MATCH OR
EXCEED PIGTAIL WIRE SIZE FOR POWER
SUPPLY AND GROUND CIRCUIT
ELECTRICAL PIGTAIL
(STELLAR SUPPLIED)
Component Installation, continued

American Eagle®30P Compressor Manual | Page 5
W/ 15AMP ATO FUSE
Electrical Connections:
Supplied with the compressor is a wire harness pigtail which has 4 leads coming off of it.
Connect the black wire to the vehicle frame or other suitable ground. Connect the red
lead to a fused power source. Mount a single throw toggle switch in a convenient location
and connect the green wire from the compressor to this switch. Connect the other switch
terminal to a fuse holder and then to a 12V power supply. The yellow wire is required from
the compressor when connecting the speed control into the system.
30P Electrical Schematic

Page 6 | American Eagle®30P Compressor Manual
AIR DELIVERY
-12 FEMALE NPT
HYDRAULIC
RETURN LINE
-12 MALE FACE SEAL
HYDRAULIC
PRESSURE LINE
-8 MALE FACE SEAL
COMPRESSOR OIL
DRAIN LINE
The hydraulic system consists of the oil reservoir, pump, manifold, motor, filters, and
hoses. A ½” 3000psi pressure line should be connected to the pressure line fitting on the
bulkhead. This line is plumbed though an internal manifold block, and then to the motor.
After the motor there is an internal cooler which the oil passes through before going to
the return line bulkhead fitting. A ¾” minimum low-pressure return line is to connect to
the return bulkhead fitting and filter before being returned to the oil reservoir. American
Eagle recommends a sufficiently-sized reservoir be provided that includes the proper
suction and return filters. The cooler on the compressor is designed and sized to cool the
air compressor efficiently. An auxiliary oil cooler is required when additional hydraulically
operated equipment is added to the hydraulic system. Pressure on the return line
exceeding 200PSI can and will cause damage to the filter, cooler, and components of the
compressor’s hydraulic system.
The airline is routed using a ¾” 200 psi air/steam hose. This delivery line should be free from
all obstructions. Note: There should be no check valve installed between the compressor
and the air tank (One is already included in the compressor package). American Eagle
recommends the installation of a ten-gallon air tank (minimum) to maintain proper
operation of the air compressor.
Hydraulic System
Air System

American Eagle®30P Compressor Manual | Page 7
Pressure Setting Instructions:
1. Always set the kick out pressure setting first. Adjust the kick out screw setting to 145 psi
minimum/150 psi maximum.
2. After kick out pressure is set, adjust the kick on screw setting to 115 psi minimum/120 psi
maximum.
3. Cycle compressor to verify correct settings.
4. For questions about this procedure, please contact American Eagle Customer Service at
800-321-3741.
Compressor Pressure Switch
Kick Out (Step 1)
Pressure Setting
Adjustment Screw
(145-150 psi)
Kick On (Step 2)
Pressure Setting
Adjustment Screw
(115-120 psi)
Note: Turning adjustment screws clockwise increases psi settings.
Turning adjustment screws counterclockwise decreased psi settings.
Pressure
Switch

Page 8 | American Eagle®30P Compressor Manual
Typical Hydraulic Circuit for Single-Section Pump
PN 30533

American Eagle®30P Compressor Manual | Page 9
Typical Hydraulic Circuit for Tandem (Two Part) Pump
PN 30532

Page 10 | American Eagle®30P Compressor Manual
Typical Hydraulic Circuit for Compressor with Auxiliary Cooler
COMPRESSOR
RETURN
PRESSURE
AUXILIARY
COOLER
SINGLE
HYDRAULIC
PUMP
SUCTION PORT
FILTER
FILTER SCREEN
HYDRAULIC
RESERVOIR

American Eagle®30P Compressor Manual | Page 11
Chapter 3 - Assembly Drawings
30P Case Assembly - PN 66354
.YTQNOITPIRCSEDTRAPMETI
166352 PANEL FRONT CPRSR SHD43/60 SHROUD1
266353 PANEL BACK CPRSR SRS40/SHD43/60 SHROUD 1
3 67903 PANEL SIDE RH SRS40/SHD43/60 SHROUD 1
467511 PANEL SIDE LH SRS40/SHD43/60 SHROUD 1
52SSDHNTB57.0X02-52.0RCSPAC1206C5
32NOLYNTALF52.0REHSAW295916
767904 PANEL LID CPRSR SRS40/SHD43/60 SHROUD 1
1ECROF#0300.21-05.7GNIRPSSAG301968
970379 HINGE ZINC BLK FLUSH SURFACE MNT DC-50-P8 1
10 70379 HINGE ZINC BLK FLUSH SURFACE MNT DC-50-P8 1
31COLYN5RGHH02-52.0TUN333011
12 69101 LATCH SWING LEVER FLUSH TRIGGER 0.91-1.81 1
21DO83.0X02-52.0TRESTUN9859131
31SSTALF52.0REHSAW7190D41
15 73654 BRKT LID GASPROP CPRSR SHROUD V2 PC WHITE1
16 73653 BRKT LOWER GASPROP CPRSR SHROUD V2 PC WHITE1
17 73723WEATHERSTRIP RIBBED 0.38X0.13X90.001
2COLYN5RGHH81-13.0TUN243081
5
6
7
1
15
3
9
13
5
6
11
14
11
5
17
14
11
42
6
12
8
14
16
11
14
11
5
18

Page 12 | American Eagle®30P Compressor Manual
30P Assembly Drawing - PN 66338
14
17
16
19 65
18
54
50
34
31 74
51
41
66
56
71 33 70
6
68
5
69
52
6
10
68
2
10
25
36
73
48
59 75
60
61
62
55 68
23
15
63
10 68 53
2
14
12
66
4
8
57
39
40
72
32
5
42
37
64
58
38
66
9
3
35
26
33 27
7
9
13
11
45
30
43
44
9
7
49
21
29
20
46
47

American Eagle®30P Compressor Manual | Page 13
30P Assembly Bill - PN 66338
ITEM
PART
DESCRIPTION
QTY.
1 0333
NUT 0.25-20 HHGR5 NYLOC
2
2 0335
CAP SCR 0.38-16X1.25 HHGR5
8
3 0339
CAP SCR 0.25-20X2.50 HHGR5
2
4 0340
WASHER 0.25 FLAT
4
5 0347
NUT 0.38-16 HH NYLOC
6
6 0351
CAP SCR 0.38-16X1.00 HHGR5
6
7 0479
CAP SCR 0.25-20X0.75 HHGR5
4
8 0482
CAP SCR 0.25-20 X 3.00 HHGR5
2
9 0521
WASHER 0.25 LOCK
6
10 0523
WASHER 0.38 LOCK
10
11 0560
FTG 6 MFS PLUG
1
12 12180
FILTER MANIFOLD SHD60 CPRSR
1
13 12813
GROMMET 1.25ODX0.125X0.625ID
1
14 13523
CPRSR V480CT66NP
1
15 13529
FILTER AIR SHD60
1
16 13577
CLAMP UNI 1.19 O.D. 5019
4
17 13638
FTG 12-12 HB-MP 90 MODIFIED CUT
2
18 14267
TUBING COPPER 0.25 X 9.00
1
19 14600
HOSE SUCTION 0.75 X 13.00
2
20 18611
SCREW #6-32X0.38 HH MACH SELF TAP
2
21 19589
NUT SERT 0.25-20X0.38 OD
2
22 19592
WASHER 0.25 FLAT NYLON
1
23 19644
BRKT MOTOR MOUNT 19644 POWDERCOAT
1
24 20451
FTG 2-2 MP-FP STREET ELBOW 90 BRASS
1
25 21393
FTG 12-12 FP-MJ BULKHEAD STRAIGHT
1
26 22183
SCREW #8-32X0.75 BTNHD SS
2
27 22186
NUT #8-32 HH NYLOC SS
2
28 2772
CAP 8FNL-S
1
29 28855
HOUR METER 12VDC TST 180-1911
1
30 3864
FTG 12-12 MJ-MP 90
1
31 4581
NIPPLE 0.75X4.00 BRASS
1
32 51841
MOTOR HYD SHD60 & SHD43 1.93 CID
1
33 5290
WASHER #8 SAE FLAT
8
34 5480
VALVE CHECK 0.75 STANDARD
1
35 61792
MANIFOLD ASM SVRV10-12SAE 3000PSI ALUM BODY
1
36 65025
FTG 12-12 MFS-MFS BULKHEAD UNION
1
37 66331
TUBE ASM 0.50 BLKHEAD TO MANIFLD SHD 21-60 ZC
1
ITEM
PART
DESCRIPTION
QTY.
38 66332
TUBE ASM 0.50 MANIFLD TO MOTOR SHD60 ZC
1
39 66333
TUBE ASM 0.75 MANIFLD TO COOLER SHD60 ZC
1
40 66334
TUBE ASM 0.75 MOTOR TO COOLER SHD60 ZC
1
41 66335
TUBE ASM 0.75 COOLER TO BLKHEAD SHD60 ZC
1
42 66337
BASE WLDMT SHD43/60 STL SHROUD
1
43 66354
SHROUD ASM CPRSR SHD43/60
1
44 66991
PLATE AL 61792 MANIFOLD MOUNT
1
45 67510
TUBE ASM 0.75 AIR CPRSR TO BLKHEAD SHD60 ZC
1
46 73652
PLUG NICKEL PLATED BUTTON 0.88
1
47 76364
WIRE HARNESS 30R/45R/65R CPRSR
1
48 77503
PANEL BULKHEAD 30P PC WHITE
1
49 78190 HOSE 0.38(200PSI)-6PL SHORT-6PL STRAIGHT-
23.5CL
1
50 8276
FTG 4-2 MP-MP 90
1
51 8278
FTG 12-12 FP-MP W/ .125 FP SPL
1
52
B0682
BRKT COOLER MOUNT SHD60
1
53
C0081
CLAMP 0.50 BLK VINYL
1
54
C0863
SWITCH PRES COMPRESSOR
1
55
C0944
CAP SCR 0.38-16X1.75 HHGR5
2
56
C1129
COOLER OIL
1
57
C1180
FTG 8-12 MFS-MORB STRAIGHT
1
58
C2053
FTG 12-8 MORB-FORB STRAIGHT REDUCER
1
59
C3480
COUPG HYD CPRSR TAPER
1
60
C4570
CAP SCR 0.31-24X0.75 HH NF
1
61
C4779
COUPG SPIDER SUL 99 BLUE URETHANE
1
62
C4781
COUPLING LOVEJOY 5/8
1
63
C4794
FTG 12-12 HB-MAORB 45
2
64
C4909
FTG TEE SL LOK 8-S5OLO-S
1
65
C5616
CLAMP ROMEX 0.50
2
66
C5968
FTG 12-12 MFS-MAORB 90
4
67
C6021
CAP SCR 0.25-20X0.75 BTNHD SS
1
68
C6353
WASHER 0.38 FLAT GR8
12
69
C6359
FAN 12.00 PULL 12 VOLT
1
70
D0075
SCREW #6-32X2.75 RH HD MACHINE
2
71
D0076
NUT #6-32 HH NYLOC
2
72
D0525
FTG 12-12-12 MFS-FFSS-MFS RUN TEE
1
73
D1318
FTG 8-8 MFS-MFS BULKHEAD UNION
1
74
D1345
FTG CPRSN 0.12NPT/0.25 TUBE
1
75
D1465
WASHER 0.31-0.178 THICK
1
76
new
Square D
copper
tube
1

Page 14 | American Eagle®30P Compressor Manual
.YTQNOITPIRCSEDTRAPMETI
1PN6IWC084VRSRPC8684C1
222686 HANDLE DIPSTICK OIL CHECK V480 1
1)063V/032V(KCITSPID938223
1211-GNIR'O1400C4
5C2279 FTG HOSE BARB 0.50 HOSE X 0.50 MNPT 2
6C6235 FTG BRASS ELL 90 DEG A/C 2
100.21X36.0ESOH691527
2SS8#PMALCESOH5664C8
1403SS00.4X57.0ELPPIN878329
1SSARBWOBLE57.0GTF6621D01
11 D1264FTG 0.75-CLOSE RED BRASS NIPPLE 1
12 5480 VALVE CHECK 0.75 STANDARD1
13 D1267FTG .75X90 DEG ST EL BRASS 441641
14 C4692FTG 0.75 JIC-ML NPT 12CTX 90 DEG EL 1
15 C0863SWITCH PRES COMPRESSOR 1
16 C5559FTG ADAPT 1/8ML-1/4FM NPT 1404-2-41
1ELPPINXEH52.0GTF6755C71
1SEE PAGE 22 FOR CLUTCH OPTIONS81
19 D0240FTG ELL 0.13 CPRSN TUBE TO NPT1
20 25448TUBE COPPER 0.25X9.00 SUH-60 1
18
8
6
7
8
6
2
3
4
20
10
9
5
11
12
13
14
16
17
15
19
1
COMPRESSOR ASSEMBLY
SUH-60 Compressor Assembly

American Eagle®30P Compressor Manual | Page 15
CRANKCASE GROUP
26
27
5
3
29
8
30
4
32
7
6
12
11
20
40
1
15
22
21
13
23
24
36
39
25
35
31
38
10
9
2
33
16
14
19
28
37
17
34
18
ITEM PART DESCRIPTION
QTY.
1 0485 CAP SCR 0.31-18X1.25 HHGR5
4
2 5813 CAP SCR 0.31-18X0.75 SH
5
3 5817 ROLL PIN 0.19X.50
1
4 5819
GAUGE OIL PSI 1.5
1
5 5820 OIL PUMP DRIVE SLEEVE V480/V360/200
1
6 5821 BEARING CARRIER OIL PUMP V360/V480
1
7 5822 GASKET BEARING CARRIER-V480 (.015)
5
8 5824 CRANKSHAFT V480 TAPER
1
9 5825 BEARING SEAL V480
1
10 5826 BEARING CARRIER CLUTCH PLT V480
1
11 6031 SCREW 0.31-18X1.00 SHC
1
12 6034 SCREW 0.31-18X1.00 SHC
4
13 22209 ROLL PIN 0.19X.63
1
14 22210 DIPSTICK OIL CHECK V480
1
ITEM PART DESCRIPTION QTY.
15 22626 PORT PLATE COVER
1
16 22686 HANDLE DIPSTICK OIL CHECK V480
1
17 22868 BREATHER CPRSR .50NPT NY8
1
18 50389 WASHER 0.885X1.115X0.064 COPPER
1
19 C0041 O'RING-112
1
20 C0050 OIL PUMP
1
21 C0052 PORT PLATE MACHINED
1
22 C0054 PORT PLATE COVER GASKET (SMALL)
1
23 C0055 OIL INTAKE PLUG
1
24 C0057 O'RING 2-115 FOR OIL PICKUP TUBE
1
25 C0058 OIL INTAKE FILTER SCREEN
1
26 C0059 OIL PUMP TRANSFER BUSHING
1
27 C0060 SPRING OIL PUMP
1
28 C0062 BREATHER BODY
1
ITEM PART DESCRIPTION QTY.
29 C0855 BEARING CONE
1
30
C0856
BEARING CONE LM67048
1
31
C1163 BEARING CUP (LM67010)
1
32 C1164 BEARING CUP (L44610)
1
33 C1174 CRANK CASE V480/360
1
34 C4703 KEY WOODRUFF 5/32 X 3/4 #8
1
35 C4841 PLUG 0.38 NPT SQ HD BLK
1
36 C5416 TUBE OIL INTAKE .38ODX3.00
1
37 C5929 FTG 8-8 FP-FP CPLR STRAIGHT BLK
1
38 C6271 FRONT PL GASKET
3
39 C6273 SNAP RING PISTON PIN N5000-62
1
40 C6275 PORT PLATE GASKET
1
Crankcase Group (Tapered Shaft)

Page 16 | American Eagle®30P Compressor Manual
CRANKCASE GROUP
11
10
8
9
7
5
6
37
36
35
31
33
32
28
30
26
27
29
25
23
24
22
38
21
17
16
15
14
20
13
19
3
34
18
12
2
1
4
39
40
ITEM PART DESCRIPTION QTY.
1 C1174 CRANK CASE V480/360
1
2 5822 GASKET BEARING CARRIER-V480 (.015)
5
3 5821 BEARING CARRIER OIL PUMP V360/V480
1
4 C1164 BEARING CUP (L44610)
1
5 22834 CRANKSHAFT V480 S
1
6 C0856 BEARING CONE LM67048
1
7 C0855 BEARING CONE
1
8 5820 OIL PUMP DRIVE SLEEVE V480/V360/200
1
9 5817 ROLL PIN 0.19X.50
1
10 C0060 SPRING OIL PUMP
1
11 C0059 OIL PUMP TRANSFER BUSHING
1
12 C0050 OIL PUMP
1
13 C6275 PORT PLATE GASKET
1
14 C0052 PORT PLATE MACHINED
1
ITEM PART DESCRIPTION QTY.
15 C0054 PORT PLATE COVER GASKET (SMALL)
1
16 22626 PORT PLATE COVER
1
17 0485
CAP SCR 0.31-18X1.25 HHGR5
4
18 6031 SCREW 0.31-18X1.00 SHC
1
19 6034
SCREW 0.31-18X1.00 SHC
4
20 22209 ROLL PIN 0.19X.63
1
21 C0055 OIL INTAKE PLUG
1
22 C5416 TUBE OIL INTAKE .38ODX3.00
1
23 C0058 OIL INTAKE FILTER SCREEN
1
24 C6273 SNAP RING PISTON PIN N5000-62
1
25 C4841 PLUG 0.38 NPT SQ HD BLK
1
26 5826 BEARING CARRIER CLUTCH PLT V480
1
27 C6271 FRONT PL GASKET
3
28 5825 BEARING SEAL V480
1
ITEM PART DESCRIPTION QTY.
29 C1163 BEARING CUP (LM67010)
1
30 5813 CAP SCR 0.31-18X0.75 SH
5
31 22686 HANDLE DIPSTICK OIL CHECK V480
1
32 22210 DIPSTICK OIL CHECK V480
1
33 C0041 O'RING-112
1
34 5819 GAUGE OIL PSI 1.5
1
35 C0062 BREATHER BODY
1
36 C5929 FTG 8-8 FP-FP CPLR STRAIGHT BLK
1
37 22868 BREATHER CPRSR .50NPT NY8
1
38 C0057 O'RING 2-115 FOR OIL PICKUP TUBE
1
39 23047 KEY FLYWHEEL 1/4
1
40 50389 WASHER 0.885X1.115X0.064 COPPER
1
Crankcase Group (Straight Shaft)