American Eagle SRS-65 User manual

®
American Eagle, Inc.
190 State Street
PO Box 169
Garner, IA 50438
800-392-3015
Fax: [phone]
www.americaneagleacc.com
Owner’s Manual
Model SRS-65
Manual Part No. 37246
Last Revision: 7/18/07
Subject to Change without Notification.
© 2006 American Eagle
Safety, Installation, Maintenance, and Operation

SRS-65 Manual
1
American Eagle Compressors are designed to
provide safe and dependable service for a
variety of operations. With proper use and
maintenance, American Eagle Compressors will
operate at peak performance for many years.
This manual contains information vital to the
safe use and efficient operation of this unit.
Following the information provided within this
manual can ensure the longevity of the
compressor. Carefully read and study the
operator’s manual before using the unit. Failure
to adhere to the instructions could result in
property damage or even serious bodily injury to
the operator or others close to the compressor.
A copy of this manual is provided with every
compressor and shall remain with the
compressor at all times. Information contained
within this manual does not cover all
maintenance, operating, or repair instructions
pertinent to all possible situations. This manual
is not binding. American Eagle reserves the
right to change, at any time, any or all of the
items, components, and parts deemed
Introduction
necessary for product improvement or
commercial/production purposes. This right is
kept with no requirement or obligation for
immediate mandatory updating of this manual.
This product manual is not intended as a
training manual for beginners or unskilled
operators. This manual offers guidelines for
correct and safe usage of the compressor,
maintenance, and troubleshooting. If more
information is required or technical assistance is
needed, please contact AE Technical Support.
Some sections of this manual contain
information pertaining to all American Eagle
manufactured compressors and may or may not
apply to your specific model.
If this manual becomes damaged, misplaced, or
unreadable at any point, or if you feel that any
part of this manual is unclear or incorrect,
please contact AE Technical Support at 800-
321-3741 or email at
[email protected]
Technical Questions, and Information [email protected]
Order Parts [email protected]
Warranty Information [email protected]
For Technical Questions, Information, Parts, or Warranty, Call Toll-Free at
800-321-3741
Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST
Or email at the following addresses:

SRS-65 Manual
2
Table of Contents
Safety Page 3
Specifications Page 4
Operation Page 5
Maintenance Page 6
Installation Page 11
Assembly Drawings Page 17
Replacement Parts Page 19
Troubleshooting Page 20
Warranty Page 22

SRS-65 Manual
3
Safety
The SRS-65 Rotary Screw Compressor will
provide safe and dependable service if operated
according to instructions. Read and understand
the safety precautions given in this manual and
on the decals attached to the shields. Failure to
do so can result in personal injury or equipment
damage.
Operators and maintenance personnel must
always comply with the safety precautions.
These precautions are given here for your
safety. Review them carefully before operating
the compressor and before performing
maintenance or repairs.
Supervising personnel should develop additional
precautions relating to the specific work area
and local safety regulations.
Precautions
Always wear safety equipment such as goggles,
ear plugs and head protection at all times when
operating the compressor.
Do not inspect or clean the compressor while
the power source is connected. Accidental
engagement of the tool can cause serious
injury.
Before performing any maintenance on the
compressor, place a warning tag on the
hydraulic power source or disconnect the hoses
from the compressor motor to prevent
accidental startup of the compressor.
Always connect hoses to the compressor before
energizing the power source. Be sure all hose
connections are tight.
Establish a training program for all operators to
ensure safe operation.
Do not operate the compressor unless
thoroughly trained or under the supervision of
an instructor.
Do not operate the compressor if it is damaged,
improperly adjusted or not completely or
properly assembled.
Never operate the compressor with any of the
guards removed.
Do not attempt to adjust or disable the
compressors air pressure relief valve. This
valve limits the air pressure to 150 PSI.
The surface of the air compressor and the
plumbing between the compressor and the
cooler may reach temperatures above 150
degrees. Touching these surfaces during
operation can cause burns.
The air taken in by the air compressor must be
free of flammable fumes and vapors.
Compressor speed should not exceed 8000
RPM.
Use and operate this air compressor only in full
compliance with all pertinent O.S.H.A.
requirements and all Federal, State and Local
codes or requirements.
This manual contains vital information for the safe use and efficient
operation of this unit. Carefully read the operators manual before
starting the unit. Failure to adhere to the instructions could result in
serious bodily injury or property damage.

SRS-65 Manual
4
Specifications
• Model:
• Weight: 313 lbs.
• Cylinders:
• Delivery: 65 CFM @ 100 PSI
• Maximum Working Pressure: 150 PSI
• Relief: 2600 PSI
• Maximum Compressor Speed: 8000 RPM
• Delivery: 65 CFM @ 100 PSI (7000-7500 RPM)
• Dimensions: 29”L x 23”W x 22”H
• Electrical: 12 VDC
• Crankcase Oil Capacity: 5 Quarts
• Oil Reservoir Capacity: Minimum: 26 Gallon Reservoir
• 19-20 GPM Hydraulic System • 2500 PSI System Pressure
• 2600 PSI Pressure Relief Setting • 12 VDC Solenoid Control Valve
• All Steel Plumbing W/ JIC Fittings • 6061 Aluminum Manifold
• 861 CFM, 12 Volt Cooler Fan • Air Pressure Control Valve
• Belt Drive • Max. Air Pressure 150 PSI
• Compressor RPM (small sprocket) • 65 CFM @ 100 PSI With
7000-7500 RPM Compressor Running @ 7000
RPM @ 20 GPM
Compressor System Description
General Information

SRS-65 Manual
5
General Information
To use the compressor, start the vehicle engine
and engage the hydraulic system. The
compressor can now be activated using the
compressor switch. This energizes the hydraulic
solenoid sending oil to the hydraulic drive motor
and starts the compressor. Through the air
pressure switch and pilot valve, the system will
now function automatically. Once engaged,
adjust the engine speed control to ensure that
the compressor speed does not exceed 8000
RPM under load. Adjustment instructions are
provided with the speed control unit.
Air Pilot Valve Operation
(Head Unloading System)
When the hydraulic system is engaged the
compressor will pump air into the receiver until
the pressure reaches 150 psi. At this time the
air pilot valve senses the pressure in the
receiver and engages an intake valve hold-open
mechanism. The compressor will run free until
the pressure in the receiver falls below 115 psi
and the air pressure valve disengages the
intake valve hold-open mechanism to allow the
Operation
Each compressor is bench tested under load at the factory to ensure proper break-in and operation.
While it is not necessary to follow any break-in procedure, the following checks should be made
before putting the unit into service and periodically during use.
compressor to pump air. See head unloading
system for detailed views and adjustment
instructions on the next page.
Operating Notes:
This reciprocating compressor must not be used
for breathing air. To do so will cause serious
injury whether air is supplied direct from the
compressor source or to breathing tanks for
later use. Any and all liabilities for damage or
loss due to injuries, death and/or property
damage, including consequential damages
stemming from the use of this compressor to
supply breathing air will be disclaimed by the
manufacturer.
The use of this compressor as a booster pump
and/or to compress a medium other than
atmospheric air is strictly non-approved and can
result in equipment damage and/or injury. Non-
approved uses will also void the warranty.
Never use plastic pipe or improperly rated
metal pipe. Improper piping materials can burst
and cause injury or property damage.
Before Start-Up
Inspect unit for any visible signs of damage.
Check the oil level in the compressor with the dipstick on the unit. If oil is needed, use American
Eagle synthetic compressor oil (P/N C0087) or an equivalent synthetic oil. Note: There may be oil
left in the crankcase from the factory bench test. Overfilling may cause the compressor to
back blow oil. Always check the oil level and fill to the designated marking on the dipstick
before putting the unit into service.
Check hoses (air and hydraulic) for weak or worn condition and make sure that all connections are
secure.
Check the air intake filters on each head to make certain that they are clean and unobstructed.
Dirty air filters are a possible cause of reduced air output.

SRS-65 Manual
6
Maintenance
The following table is a list of routine maintenance items, including service intervals. Service
intervals are listed as hours, days, or weeks, whichever occurs first. American Eagle recommends
that these service intervals be followed. Before performing any maintenance function “Lock Out” or
“Tag Out” all sources of power. Be sure all air pressure in unit is relieved. Failure to do so may
result in injury or equipment damage.
Under normal operating conditions, oil changes are required every 3 months. When operating in a
dirty environment, change the oil more frequently as your particular operating condition dictates.
General preventative maintenance includes maintaining proper fluid level in both systems and the
general cleanliness of the equipment. Proper fluids according to the specifications are required.
USE AE SYNTHETIC COMPRESSOR OIL P/N C0087.
COMPRESSOR CRANKCASE CAPACITY IS 4 QUARTS.
Service Intervals
Maintenance operation Daily Weekly Monthly Hourly
Drain air tanks
Check crankcase oil level
Check fittings and airlines
Check hydraulic fluid level
Inspect and clean air intake filters
Clean and operate safety valves
Clean cooling fins on radiator/cooler
Inspect check valve
Replace Coalescering/Separator Cartridge 12
Inspect and clean compressor valves 6
-
Replace hydraulic filter 6
Replace air filters/oil filter/compressor oil 3
Tighten all fittings and fasteners 3
Check all electrical connections 3
Inspect and clean air check valve 250

SRS-65 Manual
7
The oil level in the oil receiver container is an important factor for the operational reliability of the system.
Check Intervals:
1. Before starting unit.
2. Every 100 operating hours
Check Procedures:
1. Switch off the unit with main power and prevent it from accidentally being turned on.
2. Allow one full minute to pass after stopping compressor.
3. Unscrew the cap of the inlet connection pipe with the oil receiver discharged.
4. Check the oil level with the dipstick.
5. Add oil to level if necessary.
6. Tighten cap back into place and unit is ready to be put into service
7. Check for impermeability and replace the o-ring if required.
Note:
• The screw-type cap of the compressor crankcase is equipped with a pressure release hole, which
emits air/oil if the pressure has not been alleviated from the separator receiver. In this case wait a few
minutes for the pressure to release before removing cap totally.
• The oil fill is designed in such a way that the unit cannot be over filled. Any excess oil runs out the fill.
SRS-65 Oil Level
The condensation in the oil affects the operation safety and the life of the screw compressor unit.
If you operate the screw compressor unit for a short period of time and therefore at a low operation
temperature, i.e. below the switch temperature of the thermal oil bypass valve, you run the risk of
condensation collecting in the oil separator receiver. The relative humidity in the intake air determines the
quantity of condensation.
Possible Malfunctions:
• Insufficient compressor lubrication.
• Insufficient air/oil separation and high differential pressure in the purifier cartridge.
• Corrosion and rust formation due to condensation in the oil.
Drain the condensation regularly when the compressor unit is cold prior to startup.
Maintenance Procedure:
1. Switch off the main power to the unit.
2. Slowly unscrew the oil fill cap.
3. Unscrew the oil drain plug carefully and place a container underneath.
4. Drain the condensation from the separator receiver until oil starts to come out. Then replace the drain
plug.
5. Fill separator receiver with oil up to maximum, then close oil fill.
6. Switch on compressor and run for 3 minutes.
7. Check oil level and fill if necessary.
8. Dispose of condensation in accordance with local and federal regulations.
Condensation Drain

SRS-65 Manual
8
Note: Prior to changing the unit oil make sure the unit has an operating temperature 140-175°F
(60-80°C).
Maintenance Procedure:
1. Switch off the main power to the unit.
2. Slowly unscrew the oil fill cap.
3. Unscrew the oil drain plug carefully and place
a container underneath.
4. Drain the oil from the separator receiver until
oil stops draining out. Then replace the drain
plug.
5. Refill separator receiver with oil up to
maximum, then close oil fill.
6. Switch on compressor and run for 3 minutes.
7. Check oil level and fill if necessary. Oil
capacity is 5 quarts.
Changing the Oil
WARNING
You may change the unit oil only when the unit
has been stopped and completely discharged.
OIL FILL
OIL DRAIN
Screw compressors must be operated using the most
suitable oil for operation. The compressor manufacturer
must approve this oil for use. The oil must also be
suitable for use in unfavorable conditions such as:
contamination of the intake air by gases, solvent vapors,
exhaust gases, and high ambient temperature
conditions.
Suitable types and brands of oil may be specified on
request. Suitable screw compressor oils can be mineral
oils, synthetic oils, and biological degradable oils.
The substances and materials used in the compressor
such as seals must be taken into account when
selecting the types of oil. Corrosion or other material
degradation must not occur.
Important: Do not mix different types of oil.
Important: In the case of ambient temperatures close to
freezing, prevent the unit from freezing.
Pipeline Materials:
The oil used in screw compressors can degrade plastics
used in air pipelines.
High aging stability
High disperse capacity
Low emulsification tendency
Flash point: above 400°F/ 200°C
Pour-point: 5° below lowest ambient temperature
minimum
Minimum foaming
High corrosion protection
Hydraulic or turbine oil
Basic oil: solvate
Operating temperature: up to 230°F / 110°C
Viscosity class: ISO VG 68
Viscosity at 104°F / 40°C: ca. 42-50 mm2/s (cST)
Oil Recommendation Oil Requirements

SRS-65 Manual
9
The oil filter is located in front of the unit. Replace it after the first 50 hours of service.
Then replace it every 1000 hours of service after that (or as soon as differential pressure
is about 25 psig)
Maintenance procedure:
1. Switch off the main power to the unit. Fully relieve the unit
of pressure.
2. Slowly unscrew and remove the oil filter with an oil filter
wrench.
3. Grease the new filter gasket.
4. Before mounting the new filter hold it upright and fill it with
the same type of oil as the compressor crankcase.
5. Thread the new filter onto the compressor by hand without
any tools.
6. Run compressor for 3 minutes.
7. Check oil level and fill if necessary.
Oil Filter
Oil Filter
P/N 15323
The separator cartridge is disposable and is located on top of the filter support.
The cartridge has to be replaced at least once per year and at a maximum of 5000 operating hours. The pressure will
read above 14 psig. If intake air is often contaminated or the oil quality is poor, the cartridge will tend to clog earlier
and will need changed more often.
Maintenance Procedure:
1. Switch off the main power to the unit. Fully relieve the unit
of pressure.
2. Slowly unscrew and remove the cartridge with an oil filter
wrench.
3. Screw the new cartridge onto the filter support using only
your hands.
4. Write the date of change, and the operating hours on the
cartridge.
5. Check to make sure that the cartridge is tight.
6. Run compressor for 3 minutes.
7. Check cartridge to make sure it is tight.
Separator Cartridge
SEPARATOR
CARTRIDGE
P/N 15324
The air intake filter element shall be replaced every 100 hours of running time. The filter may require changing more
often if the air pollution level is higher.
Maintenance Procedure:
1. Switch off the main power to the unit. Protect the unit from
accidental re-start.
2. Open the filter lid and carefully remove dust and debris
from the intake tray.
3. Carefully remove old filter and clean or renew it.
• Clean the filter by knocking the filter against your hand.
• Clean the filter with compressed air.
4. Close filter lid.
5. Test run the compressor to ensure proper installation.
ATTENTION: Any dirt or debris that reaches the intake
will be ingested into the compressor and could cause
irreversible damage.
Intake Filter
AIR FILTER
P/ 15322
FILTER LID

SRS-65 Manual
10
NEW BELT
INSTALLATION TENSION: 98.0 lbf
TENSIONING FORCE: 6.8 lbf
BELT DEFLECTION: 9/64 in
SPAN LENGTH: 9.50 in
USED BELT
INSTALLATION TENSION: 65.4 lbf
TENSIONING FORCE: 4.8 lbf
BELT DEFLECTION: 9/64 in
SPAN LENGTH: 9.50 in
Belt Tension
Force Applied
Belt Deflection
Span
At the factory, the relief valve is set at 64psi. When servicing the screw compressor a check of the
minimum pressure may be necessary.
Minimum Pressure Readjustment Procedure:
1. Remove the locknut.
2. Turn the adjusting screw (turning the screw in
increases the pressure).
3. Tighten locknut in place.
Minimum Pressure Valve
ADJUSTING SCREW
LOCK NUT
For the operational safety of the unit clean the cooler regularly. Keep the cooling fins clean, this is
a must to achieve maximum cooling from your cooler. Adequate cooling will prolong the life of your
screw compressor. To clean your cooler use compressed air, steam jet, or a cleaning agent.
Maintenance Procedure:
1. Switch off the main power to the unit. Protect the
unit from accidental re-start.
2. Remove cooler housing.
a. Discharge unit.
b. Drain oil.
c. Remove cooler.
3. Clean and remove dirt.
4. Reassemble parts onto unit.
5. Check and fill oil level.
6. Test run the compressor to ensure proper
installation and recheck oil level.
Hydraulic Oil Cooler/Compressor Oil Cooler
Oil Cooler

SRS-65 Manual
11
Installation
Pump Assembly:
The pump assembly may either be installed
directly on the PTO or as an optional
method, may be driven by a driveline from
the PTO. Pump manufacturers provide
specific installation information for their
products and should be consulted if
questions arise.
Note: A Dual or Tandem
Hydraulic Pump is recommended when
additional hydraulically operated equipment are
added to the hydraulic system.
PTO Assembly:
Check with the PTO manufactures
representative for specific instructions
regarding your particular make, model, and
year of vehicle. As some trucks may require
modification of the transmission cross
member and the exhaust system, the
manufacturer’s instructions should be
followed to insure proper installation of the
PTO.
Compressor Assembly:
Prepare the mounting location of the
compressor by locating and drilling four (4)
holes, 1/2” diameter as per the mounting
pattern of the air compressor base. Using
four (4) 3/8” x 1.25 GR-5 cap screws, 3/8”
flat washer, and 3/8” nyloc nut, secure the
compressor in place. The compressor is air
cooled, and must have a clean supply of
cooling air to the fan with minimum
restrictions. Adequate space must be
provided for proper circulation of air.
Electrical Connections:
From the air pressure switch there are two
(2) wires, red and black, running to the
outside of the compressor housing. Connect
the black wire to the vehicle frame or other
suitable ground. Mount a single throw
toggle switch in a convenient location and
connect the red wire from the compressor to
this switch. Connect the other switch
terminal to a fuse holder and then to a 12-
volt power supply. A third wire is required
from the air compressor switch when
connecting the speed control into the
system. (See drawing on next page)
Electric Speed Control:
An optional electric or electronic speed
control must be used to maintain proper
operating speed of the air compressor. The
engine speed control will automatically
increase from idle to preset speed when
engaged and decrease when disengaged.
COMPONENT INSTALLATION
This section pertains to the installation of the air compressor, PTO, pump and other related items.
The instructions are intended as a guide to assist you with particular installation. These instructions
will provide only general information.
FAN
GND
CPRSR
SPD CTRL
PRESSURE
SWITCH
LINE
MOTOR
HYDRAULIC
MANIFOLD
COMPRESSOR (12V INPUT)
GROUND
SPEED CONTROL
C
B
A
C
B
A

BLACK WIRE
RED WIRE
(NOT USED)
RED WIRE
(NOT USED)
SRS-65 Manual
12
SRS-65 Electrical Installation
USE THIS PORT FOR
THE TEMP GAUGE
PROBE DO NOT ATTEMPT TO INSTALL
TEMPERATURE GAUGE INTO THIS
PORT. DAMAGE WILL RESULT!
Temperature Gauge Installation

SRS-65 Manual
13
Hydraulic System:
The hydraulic system consists of the pump, oil reservoir, filters and hoses. Installed on the
compressor is a valve block assembly that controls the flow to the hydraulic motor. To this
block, a 1/2” high-pressure hose must be attached. This hose comes from the hydraulic pumps
pressure side. A 3/4” minimum low-pressure return line is connected to the oil cooler outlet and
is routed to the oil reservoir. American Eagle recommends a sufficient sized reservoir be
provided that includes the proper suction and return filters. The cooler on the compressor is
designed and sized to cool the air compressor efficiently. An auxiliary oil cooler is required
when additional hydraulically operated equipment are added to the hydraulic system. Pressure
on the return line exceeding 200 PSI can and will cause damage to the filter, cooler, and
components of the compressor hydraulic system.
RETURN LINE
AIR DELIVERY
PRESSURE LINE
Air System:
The airline is routed using a 3/4” (200 psi) air hose. This delivery line should be free
from all obstructions. When connecting to an air tank (American Eagle recommends a
minimum of a ten gallon air tank be installed to maintain proper operation of the air
compressor), a check valve must be installed.
Component Installation Continued...
General Install Note:
When installing any air compressor, good manufacturing processes should be used. It
is critical to allow for proper air circulation around the compressor assembly and all
heated air should be allowed to exhaust to the outside if the compressor is mounted in
an enclosed compartment. Maximum operating temperatures of the air compressor
should not be exceeded.

SRS-65 Manual
14
Compressor Pressure Switch
Pressure Setting Instructions:
1. Always set the kick out pressure setting first. 145 psi minimum/150 psi maximum.
2. After kick out pressure is set, adjust the kick on screw setting at 115 psi minimum/120 psi
maximum.
3. Cycle compressor to verify correct settings.
4. For questions about this procedure, please contact Stellar Customer Service (Page 1).
Kick On (Step 2)
Pressure Setting
Adjustment Screw
(115-120 psi)
Kick Out (Step 1)
Pressure Setting
Adjustment Screw
(145-150 psi)
Note: Turning adjustment screws clockwise
increases psi settings. Turning adjustment screws
counterclockwise decreased psi settings.
+
+
-
-
Location inside box of SRS Compressors

SRS-65 Manual
15
PN 30533
PN 30532
Typical Hydraulic Circuit for Single Stage Pump with
Multiple Components
Typical Hydraulic Circuit for Tandum (Two Part) Pump with
Multiple Components

SRS-65 Manual
16
Typical Hydraulic Circuit for Compressor
with Auxiliary Cooler
COMPRESSOR
RETURN
PRESSURE
AUXILIARY
COOLER
SINGLE
HYDRAULIC
PUMP
SUCTION PORT
FILTER
FILTER SCREEN
HYDRAULIC
RESERVOIR

77
74
72
63
73
1
61
62
63
64
8
21
44
49
51
34
33
34
32
31
45
46
47
11
19
27
28
25
7
24
23
22
40
29
30
10
98
71
8
13
12
14
6
11
20
18
19
5
50
53
34
11
48
39
38
35
7
68
43
15
70
67
66
41
55
56
59
58
57
2
4
3
15
16
17
42
60
65
57
36
37
54
34
52
76
64
69
75
26
.Y
T
QN
OI
T
P
IR
CSEDTR
APME
T
I
131028 BASE WLDMT CPRSR SRS65 1
229391 CPRSR SRS NK60-2 ROTORCOMP 1
317583 CAP SCR 10MMX30MM HHGR5 4
4
K
CO
L83
.0
RE
H
S
A
W32
504
16
6
D
H
S
R
SR
PC
L
A KC
OLB
5
70
3
C
5
6 C0910 CAP SCR 0.25-20X2.75 HHGR5 2
70343 WASHER 0.31 USS FLAT ZINC 10
80333 NUT 0.25-20 HHGR5 NYLOC 5
1S-O
L
O5F 21-
8
TPADAGTF
0
811C9
1S-L
N
F8
P
A
C2
77201
11 C2142 FTG ADAPT ML O'RING/ML 12-F5OLO-S 3
12 C4914 VALVE RELIEF CP-200-1-B-0-A-C 1
1DNL
O
S
E
VLAV3
1
94C31
1G
E
D0
9GTF
5
41
6
C
41
15 22860 FTG ADAPT MBSPP/FNPT 1/2-1/2 F4OHG MOD 2
16 13579 NIPPLE 0.50X2.50 BRASS 80300-0825 1
18
-604
5XE
HEPIP05.0PAC658
21
71
18 C0078 HOSE CLAMP #8 RUBBER COATED 1
19 0479 CAP SCR 0.25-20X0.75 HHGR5 5
20 21393 FTG BULKHEAD 12WGTX-WLN 1
15
6
S
R
SMS
A L
IORELO
OC
4510
3
1
2
1TNMNAF56SRSDUORHS2301322
23 0485 CAP SCR 0.31-18X1.25 HHGR5 4
4K
COL
13
.0
RE
H
SAW225042
25 5735 NUT SERT 0.31-18X0.50 OD 4
1
T
LOV21HSUP 0
0
.61NA
F1
4
2
862
.
YT
QN
OI
T
P
IR
CSEDTR
APM
ETI
4KCOL
5
2.0REHS
AW1
25072
28 19589 NUT SERT 0.25-20X0.38 OD 4
29 12122 BOLT 0.38X1.00 EYE 567-23-ZN 1
1HH
6
1-83
.
T
UN5
3
5
0
0
3
31 21400 FTG SWIVEL NUT/MSTR .50 8F65OX 1
32 21299 FTG ADAPT MBSPP/MJIC 8-8M40M 1
33 22018 VALVE THERMO R-2323 SRS40 1
34 21297 FTG 90 MBSPP/MJIC 8-8C4MX 4
156SRSTNMR
O
T
O
M
T
KRB7
6
6
0
353
1
M
M
5
3XH
G
NIHSUB2401
3
6
3
37 34538 SPROKET GOODYEAR EAGLE PD Y-36S-H 1
100
.1
G
NI
HSUB8
81
6C
83
39 34539 SPROKET GOODYEAR EAGLE PD Y-90S-QD 1
40 31043 BELT GOODYEAR EAGLE PD Y1000 1
41 31035 MOTOR HYD PLM3022SO-33S5-LOD/OF-N-C 1
1OLO5F61-21TPAD
A
GTF9
6
22C24
43 7351 FTG ST TH ELBOW 45 DEG 12V5OLO 1
44 C4498 FTG ORB/JIC STRT CONNT 12-F5OX-S 1
45 4594 FTG STRGHT THRD CONNECT 8F5OX 1
46 4593 FTG SWIVEL NUT TEE 8R6X 1
47 33715 HOSE 0.75(381-JC-J9-12-12-12-13.00) 1
48 33716 HOSE 0.75(381-JC-JC-12-12-12-14.00) 1
49 33691 TUBE ASM 0.75 COOLER/MANIFOLD SRS65 1
50 33692 TUBE ASM 0.75 AIR/BULKHEAD SRS65 1
51 33693 TUBE ASM 0.50 COOLER/THERMVLV SRS65 1
52 33694 TUBE ASM 0.50 CPRSR/COOLER SRS65 1
.
YT
Q
NO
ITPIRCSED
T
R
A
P
M
ETI
53 33695 TUBE ASM 0.50 CPRSR/THERMVLV SRS65 1
54 21300 FTG 90 MJIC/MBSPP 12-8C40M 1
55 C0863 SWITCH PRES COMPRESSOR 1
56 8277 FTG ST L 0.25 MNPT/0.125 FNPT SPL 1
57 C6245 ELBOW 0.25 OD BRASS AIR 2
58 8158 NIPPLE 0.25 X CLOSE BRASS 1
59 21298 FTG ADAPT MBSPP/FNPT 1/4-1/4 F4OHG 1
60 21549 PANEL GAUGE MNT SRS40 1
61 21649 GAUGE AIR SWICHGAGE PSB20PHL200 1
62 21650 GAUGE OIL TEMP TSB20TVD3006125SR240 1
63 C6021 CAP SCR 0.25-20X0.75 BTNHD SS 8
6TALF52.0R
E
HSAW04
3
046
1
S
SARB31
.
0RE
L
PU
OC
161225
6
66 5419 FTG 0.50-0.25 BUSH RED BRASS 1
1#002FEILE
R
EVLAV405
5
C76
68 26025 CAP SCR 0.50-13X2.25 HHGR5 2
69 0352 WASHER 0.50 USS FLAT ZINC 4
70 C6106 NUT 0.50-13 HHGR5 NYLOC 2
71 4591 PLUG STR HOLLOW HEX 0.75 12-HP5ON 1
15
6S
RS
MS
A
D
U
ORH
S
224
13
2
7
73 19592 WASHER 0.25 FLAT NYLON 6
256-SRS LACED408947
75 31030 ANGLE MNT FRONT CPRSR SRS65 1
76 0480 CAP SCR 0.25-20X1.00 HHGR5 2
2COLYNHH81-13.0TUN243077
78 C6072 BOSCH RELAY 1
79 19590 WIRING HARNESS 1
SRS-65 Manual
17
Assembly Drawings
Compressor Assembly

SRS-65 Manual
18
SRS-65 Tube Routing

SRS-65 Manual
19
Replacement Parts
HYDRAULIC COMPONENTS/DRIVE PARTS
PART# DESCRIPTION
C4914 Relief Valve
C4913 Solenoid Valve
31035 Hydraulic Motor
34539 Sprocket (Hyd Motor)
34538 Sprocket (Compressor)
C6188 Bushing (Hyd Motor)
31043 Belt
30154 Oil Cooler
C3075 Aluminum Manifold Block
33692 Tube Assembly Air/Bulkhead 0.75
33691 Tube Assembly Cooler/Manifold 0.75
33693 Tube Assembly Cooler/Thermo-Valve 0.50
33694 Tube Assembly Compressor/Cooler 0.50
33695 Tube Assembly Compressor/Thermo-Valve 0.50
22018 Thermo Valve
ELECTRICAL/AIR PRESSURE COMPONENT
PART# DESCRIPTION
C0863 Pressure Switch
8241 Fan 16.00” Pull 12 Volt
C6072 Bosch Relay
19590 Wire Harness
21649 Air Switch Gauge
21650 Oil Temperature Gauge
C5504 Valve Relief 200 # (Air)
AIR/OIL FILTER COMPONENTS
PART# DESCRIPTION
15322 Air Filter
15323 Oil Filter
15324 Coalescering Filter (Separator Cartridge)
C0087 Synthetic Compressor Oil
33147 SRS65 Compressor Service Kit (Includes all items above)
COMPRESSOR COMPONENTS
PART# DESCRIPTION
NA Inlet Solenoid Control Valve
NA Inlet Solenoid Control Valve Assembly Complete
NA Shaft Seal Kit
NA Shaft Bearing Kit
NA Solenoid 24 Volt DC
29391 Compressor (Air End)
NA Separator Head Maintenance Kit