American Standard Low Profile Studio S Toilet Elongated Right Height with Seat... Maintenance manual

RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench
Hacksaw Wax Ring/Gasket Closet Bolts
Sealant Tape Measure Carpenters Level
ITEMS INCLUDED
x1 T-Handle
x2 T-Bolt Nuts
SAVE FOR FUTURE USE
2
1
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020
NOTE: Pictures may not exactly define contour of china and components.
Low Profile Studio® S Toilet
Model 2548A - Elongated, Right Height®with Seat
7302429-100 Rev. 1 2/20
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 140 years.To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
!
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
IMPORTANT:
Water supply on the wall is required at 10" (254mm) minimum from centerline of the toilet. See rough-in for outside toilet supply line installation.
For behind toilet or hidden supply line installation, install supply at centerline of toilet 11-1/2" (292mm) above finished floor using 'compact' 1/2"
1/4 to 1/2 turn shutoff valve.
NOTE: Depending upon the compact 1/4 turn supply valve purchased, ensure it will correctly fit and operate at the location behind the trap way
inside the toilet!
Check your supply and hose dimensions. Requires a 1/2" (13mm) Supply Valve and Hose.
The geometry of the toilet gives space for these 2 supply line installation locations.
20" x 1/2" Flexible Supply Hose for outside and inside installation of toilet supply line.
Standard 1/2" Supply valve for outside toilet installation or 1/2" 1/4-1/2 turn compact
supply valve for behind or hidden supply line installation.
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
Two water supply line locations are suggested with this toilet, outside of toilet or behind toilet locations.
Water supply valve will need to be relocated. Refer to roughin for water supply locations suggested.
SUPPLY
LINE
1" (25 mm)
16-1/2"
(419 mm)
31-1/8"
(790 mm)
*
5-1/2"
(140 mm)
15-3/8"
(392 mm)
16-3/8"
(416 mm)
12"
(305 mm)
*
11-1/2"
(292 mm)
FINISHED WALL
FINISHED FLOOR
FINISHED
FLOOR
*
10"
(254 mm)
18-1/2"
(468 mm)
BEHIND TOILET
SUPPLY LINE

6
CONNECT SUPPLY HOSE TO SYSTEM
Connect water supply hose to connection in back of
toilet for supply line outside of toilet. See Figure 1.
Note: This will ease installation of supply hose
once toilet is installed.
For supply line that is installed behind the toilet,
connect supply hose to Shut-Off Valve first.
Remove Dust Cap by pulling straight up as shown
in Figure 1.
7302429-100 Rev. 1 2/20
- 2 -
CLOSET
FLANGE
CLOSET
BOLTS
A
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and
slide into place 6" (152 mm) apart and parallel to wall.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening. Ensure supply hose is outside of toilet before installing, for outside toilet supply line. Install toilet on closet flange so
bolts project through mounting holes.
NOTE: To better view closet bolts when lowering toilet over flange, view through Seat Post Openings to align closet bolts through toilet mounting
holes while shinning a flashlight. (reference FIGURE A)
b. Place T-handle through hole opening of seat post about 3 inches and align with bolt. Carefully place plastic flange nut onto T-handle with your free
hand, then lower down over bolt of waste flange and loosely tighten. Repeat for opposite side. (reference FIGURE B)
5
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet.
4
3
WAX RING
WATER SUPPLY CONNECTION TO TOILET
T-HANDLE
FIGURE A FIGURE B
SEAT POST OPENING
FIGURE 1
DUST
CAP
TOILET WATER
SUPPLY CONNECTION
REGULATOR
Positioned for
outside of toilet
supply connection.

7302429-100 Rev. 1 2/20
- 3 -
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
INSTALL COVER
Install rear seat cover by snapping into place.
!WARNING: Do not use plumber’s putty, pipe dope, or any other sealant on the water
supply connection. If the connection leaks after hand tightening, replace the supply line.
Warranty is void if any type of sealant is used on the water supply connection.
9
a. Position toilet squarely to wall and, with a rocking motion, press
bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
b. Once toilet is fully installed and flange nuts secured, carefully turn the
Regulator to the right (clockwise). This will give additional clearance to
connect the supply line coming from behind the toilet to the Regulator.
Turn water supply ON and flush toilet approximately 3 times to fully
prime toilet and allow approximately 45 seconds between flushes to
fully prime system with water. Check for any leaks.
c. Apply sealant around base perimeter. Smooth off the bead of sealant
around base. Remove excess sealant.
CAUTION: DO NOT OVERTIGHTEN
NUTS OR BASE MAY BE DAMAGED!
!
INSTALL TOILET
7
8INSTALL TOILET SEAT:
Install toilet seat in accordance with manufacturer's directions.
BOLTS CLOSET FLANGE
FLUSH BUTTON
REAR SEAT COVER

Does not flush
Poor or sluggish flush
Toilet leaks
Toilet does not shut off
a. Water supply valve closed.
b. Supply line blocked.
c. Flush button damaged.
a. Supply valve partly closed.
b. Plugged inlet strainer.
c. Supply pressure too low.
d. Partially clogged trapway and/or drain pipe and/or vent.
e. Malfunctioning pressure regulator.
a. Poor bowl to floor connection.
b. Seals or rubber O rings in flush system defective.
c. Poor supply line connection.
a. Supply pressure too low.
a. Open valve and allow water to fill system.
b. Shut off water supply, disconnect supply line and inspect all gaskets.
c. Inspect flush button, if damaged call customer service.
a. Open supply valve fully. Be sure supply hose is not kinked.
b. Shut off water supply, remove regulator and clean strainer.
Reference “Removing/Cleaning Regulator.
c. Normal supply pressure must be at least 30 psi.
d. Remove obstruction. Consult a Plumber if necessary.
e. Replace pressure regulator. Call Customer Service.
a. Review Step 4 through 7.
b. Call Customer Service.
c. Check water supply line for leaks.
a. Normal supply pressure must be at least 30 psi.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
REMOVING/CLEANING REGULATOR
Depending upon the water quality or debris that can come into the toilet from the water supply, it may be necessary to remove and clean the
"Inlet Strainer" in the Regulator to ensure the toilet flushes correctly.
a. Shut off water supply to toilet.
b. Remove Rear Seat Cover.
c. Disconnect water supply hose on Regulator end. (reference Figure 1 in Step 5.)
d. Turn Regulator Counter Clock Wise (to the left) and remove regulator.
e. Remove Inlet Strainer (filter) with a small needle nose plier. There is a small plastic tub in the strainer which can be used to pull out the
strainer using the pliers.
f. Inspect Inlet Strainer filter screen and remove any dirt or debris from screen by running through water.
g. Insert Strainer back into Regulator and re-connect Regulator to system.
h. Connect water supply hose to Regulator and turn water supply back ON. Allow system to fill with water and test flush several times until toilet
flushes correctly and check for leaks.
i. Replace Rear Seat Cover.
7302429-100 Rev. 1 2/20
- 4 -
In the United States:
American Standard Brands
1 Centennial Ave
Piscataway, NJ 08854
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Canada:
LIXIL Canada ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
INLET
STRAINER
END
REGULATOR
INLET
STRAINER