Ameriwood AX1 User manual

B
WARNING
ameriwoodhome.com
Follow Ameriwood Home
Keep this Assembly Manual for future reference
- Anchor unit to stud in wall
- Do Not allow children to climb on unit
- Put heavy items on lower shelves or drawers
- Two people required for assembly
9291096COM
BB349291096COM
Side Cabinet (Left/Right)

Contact Us!
Helpful Hints
2
ameriwoodhome.com
Do NOT return this product!
Contact our friendly customer service team first for help.
Call us!
1-800-489-3351
Monday-Friday
9am - 5pm CST
Visit ameriwoodhome.com
Assembly Tips
- Open your item in the area you plan to keep it to avoid excessive heavy liing.
- Idenfy, sort and count the parts before aempng assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a
R (right) and L (le) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
Tube
You
Tube
You
PEOPLE NEEDED FOR ASSEMBLY:1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR

Before You Start
Hardware Assembly Method
3
ameriwoodhome.com





This Hardware Assembly Method will be used throughout the assembly process
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, Phillips Head
Screwdriver, Hammer and a Power Drill with a 5/16” (8mm)
drill bit.
Failure to do so may result in stripping the screw.
Quick
Tip
11
12
13
16

ameriwoodhome.com
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
1
3
2
4
4
Refer to the enlarged diagram to idenfy the parts on the HINGES.The TOP OPENER may need
some adjustments. Follow the text below to make needed adjustments.
TOP OPENER ADJUSTMENTS:
To adjust the
TOP OPENER from front to back , loosen the
mounng screw several turns, then turn the adjusng
screw in or out. Tighten the mounng screw aer making
adjustments.
To adjust the
TOP OPENER side to side, loosen both ver-
cal adjustment screws. Move the
TOP OPENER up or down
to the desired locaon. Tighten the screws aer making
adjustments.
To adjust the
TOP OPENER up or down , loosen the mounng screw one turn and move the TOP
OPENER
in or out, as needed.
Tighten the mounng screw aer making adjustments.

Board
Not actual size
5
ameriwoodhome.com
C
x4
T9291096030
SMALL WOODEN LEGS
D
x1
T9291096040
SUPPORT LEG
A
x1
T9291096010
TABLE TOP
B
x2
T9291096020
BIG WOODEN LEGS
G
x2
T9291096070
CABINET TOP OPENER
H
x2
T9291096080
FIXED SHELF
E
x1
T9291096050
BOTTOM PANEL
F
x1
T9291096060
CABINET TOP PANEL
K
x1
T9291096110
CENTER PANEL
L
x1
T9291096120
CENTER BACK PANEL
I
x1
T9291096090
LEFT SIDE PANEL
J
x1
T9291096100
RIGHT SIDE PANEL
O
x1
T9291096150
LEFT SIDE DOOR
P
x1
T9291096160
RIGHT SIDE DOOR
M
x1
T9291096130
BACK PANEL
N
x2
T9291096140
ADJUSTABLE SHELF

Part List
Actual Size
6
ameriwoodhome.com
3
x36
TAT0061
CAM COVER
4
x8
TAT0071
SHELF SUPPORT
1
x36
TAT0051
CAM BOLT 15/18
2
x36
TAT0052
CAM LOCK 15/18
7
x4
TAT0081
HOLE PLUG
8
x30
TAT0091
WOOD DOWEL
5
x24
TAT0001
WOOD SCREW
6
x2
TAT0002
WOOD SCREW 8 X 303.5 X 16 3.5 X 12 15 MM
NOTE! Hardware pack inside 9291096COM1

Part List
Not Actual Size
7
ameriwoodhome.com
11
x6
TAT0041
WASHER-FLAT 5/16”(RB)
12
x6
TAT0042
WASHER-SPRING 5/16”(RB)
9
x7
TAT0044
ADJUSTABLE GLIDE
M6 X 25 MM X 22 MM
10
x6
TAT0101
BOLT M6 x35MM
M6 X 35MM
15
x4
TAT0036
PNEUMATIC HINGES
5/8” FULL OVERLAY
16
x1
TAT0045
WRENCH 13 MM
13
x4
TAT0043
NUT-HEX NUT
5/16” 18MM(RB)
14
x1
TAT0032
PUSH LOCK
BLACK
17
TAT0121
L-KEY M4
x1

8
ameriwoodhome.com
Step 1
Screw the ADJUSTABLE GLIDES (9) into the two BIG WOODEN LEGS (B), four SMALL WOODEN
LEGS (C) & SUPPORT LEG (D).
B
C
X2
X4
D9
9
TAT0044
x7

9
ameriwoodhome.com
Fasten the BIG WOODEN LEGS (B) to TABLE TOP (A).
IMPORTANT! Align holes of BIG WOODEN LEGS (B) with proper holes of TABLE TOP (A).
B
A
B
11
12
13
16
Step 2
12
TAR0042
x411
TAT0041
x4 16
TAT0045
x113
TAT0043
x4

10
ameriwoodhome.com
Fasten the SMALL WOODEN LEGS (C) to BOTTOM PANEL (E) .
IMPORTANT! Align holes of SMALL WOODEN LEGS (C) with proper holes of BOTTOM PANEL (E) .
C
C
C
E
Step 3
10
TAT0101
x4 17
TAT0121
x1
10
17

11
ameriwoodhome.com
D
E
Step 4
Fasten the SUPPORT LEG (D) to BOTTOM PANEL (E).
Step 5
7
TAT0081
x4
7

12
ameriwoodhome.com
IJ
KH
x2
Insert the WOOD DOWELS (8) into the holes shown in the Panels (H), (I), (J) & (K).
Step 6
8
TAT0091
x20
8

13
ameriwoodhome.com
L
M
Step 7
8 x8
8
Insert the WOOD DOWELS (8) into the holes shown
in the Panel (L) & (M).
TAT0091

14
ameriwoodhome.com
A
B
B
Step 8
8 x2
8
Insert the WOOD DOWELS (8) into the holes shown
in the TABLE TOP (A).
TAT0091

15
ameriwoodhome.com
F
CAUTIONS
Please drill slowly to avoid the panel damage.
USE POWER TOOL (NOT INCLUDE)
F
Step 9
IMPORTANT! Drill these holes through with a 5/16” (8mm) drill for RIGHT SIDE assembly shown.
IMPORTANT! Drill these holes through with a 5/16” (8mm) drill for LEFT SIDE assembly shown.

16
ameriwoodhome.com
E
F
Step 10
1
TAT0051
x20
Insert the CAM BOLTS (1) into all holes shown in Panels
(E) & (F).

17
ameriwoodhome.com
L
I
J
M
Step 11
1 x16
TAT0051
Insert the CAM BOLTS (1) into all holes shown in Panels
(I), (J), (L) & (M).

18
ameriwoodhome.com
Proper orientation of CAM LOCK
Tip
Quick
K
I
J
M
H
L
x2
Step 12
2 x362
TAT0052
Insert the CAM LOCKS (2) into all holes shown in Panels
(H),(I), (J), (K), (L) & (M)
The arrow in the
CAM LOCK (2) must
point toward the
hole in the edge
of the board.

19
ameriwoodhome.com
M
P
Step 13
5
TAT0001
x1615
TAT0036
x4
Step 14
6
TAT0002
x2
TAT0032
x1
6
14
5
15
14

20
ameriwoodhome.com
M
H
H
L
Step 15
3
TAT0061
x8
3
Step 16
CAM LOCKS (2).
ghten the CAM LOCKS (2). Press the CAM COVERS (3) into the