Ametek Crystal Pressure User manual

Data Entry Foot Switch Operation Manual

Contents
Overview.................................................................3
Introduction ..............................................................3
Instructions .............................................................4
Installation & Setup ........................................................4
Operation .................................................................4
Support ..................................................................5
Contact Us ................................................................5
Warranty ..................................................................5

Overview 3
Data Entry Footswitch Operation Manual
Overview

INTRODUCTION
The footswitch can signicantly improve the speed at which data collection takes place by allowing the operator to focus on the task without needing to click
a mouse button or press a key on the keyboard. The actual use of the footswitch is application dependent, and is documented in the manual that accompanied
your Crystal Engineering software package. For example, in FastCalXP, the foot switch acts as a Next Data Point function, allowing the operator to keep his
hands on the comparator during data collection.
Crystal Engineering is the company that designs, manufactures, markets, and services the nVision reference recorder, XP2i digital test gauge, 30 series pressure
calibrators, MultiCal multimeter pressure adapters, and a variety of industry specic pressure measuring equipment. Crystal Engineering pioneered features like
full temperature compensation and “of reading” rated gauges and calibrators. Pressure measuring equipment is the only thing we do and that’s why we say:
™

Instructions 4
Data Entry Footswitch Operation Manual
Instructions

INSTALLATION & SETUP
The foot switch comes in two pieces. The Control Module, which has an attached USB cable and two 1/8" sockets, and the Foot Switch, which has an
attached cable ending in an 1/8" plug.
Note: When connecting the Foot Switch to a computer for the rst time, it is best to connect it after your computer has booted up and is logged in. This
will enable the “new device detected”message to be displayed, which usually completes within less than a minute. The process will be repeated
if you plug the device into a dierent USB port, even on the same computer.
1 Connect the control module to any available USB port.
Note: No drivers are required for operation. The foot switch may be connected before or after the installation of your Crystal Engineering software.
2 Plug the foot switch into the left socket on the control module, as shown in the photo, and place the foot pedal in a convenient location.
Note: If using the Elite 2 foot switch, plug the cable into the right socket.

OPERATION
Pressing the foot switch should have no eect except as appropriate within your Crystal application, and should not have any aect on other Windows
applications. See your software user’s manual for more information. Control Module and Foot Switch
Foot Switch cable plugged into the left socket

Support 5
Data Entry Footswitch Operation Manual
Support

WARRANTY
Crystal Engineering Corporation warrants the Data Entry Foot Switch to be free from defects in material and workmanship under normal use and service for one
(1) year from date of purchase to the original purchaser. It does not apply to batteries or when the product has been misused, altered or damaged by accident
or abnormal conditions of operation.
Crystal Engineering will, at our option, repair or replace the defective device free of charge and the device will be returned, transportation prepaid. However, if
we determine the failure was caused by misuse, alteration, accident or abnormal condition of operation, you will be billed for the repair.
CRYSTAL ENGINEERING CORPORATION MAKES NO WARRANTY OTHER THAN THE LIMITED WARRANTY STATED ABOVE. ALL WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM THE DATE OF PURCHASE.
CRYSTAL ENGINEERING SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER IN CONTRACT, TORT OR OTHERWISE.
Note: (USA only) Some states do not allow limitations of implied warranties or the exclusion of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you specic legal rights and you may have other rights which vary from state to state.

CONTACT US
USA
Crystal Engineering • California
Tel [phone]
Fax [phone]
[email protected]
Manseld & Green • Florida
Tel [phone]
[email protected]
United Kingdom
Tel [phone]
[email protected].uk
France
Tel [phone]
general.lloy[email protected]
Germany
Tel [phone]
info.mct-[email protected]
Denmark
Tel [phone]
[email protected]
India
Tel [phone]
[email protected]
Singapore
Tel [phone]
[email protected]
China
Shanghai
Tel [phone]
Beijing
Tel [phone]
Guangzhou
Tel [phone]
[email protected]
If calling, have ready the model number, serial number, date of purchase, and reason for return. You will receive instructions for returning the device to us.

© 2015 Crystal Engineering Corporation
708 Fiero Lane, Suite 9, San Luis Obispo, California 93401-8701
3323.C