AMGO Hydraulics 407-P Manual

Original
Four Post Parking lift
Model: 407-P

CONTENTS
Product Features and technical Specifications ...............................................1
Installation Requirement ........................................................................2
Steps of Installation ..............................................................................4
Exploded View ......................................................................................28
Test Run ………........................................................................................33
Operation Instruction .............................................................................34
Maintenance .........................................................................................34
Trouble Shooting ...................................................................................36
Lift safety tips........................................................................................36

1
I. PRODUCT FEATURES AND SPECIFICATIONS
4-POST MODEL 407-P FEATURES
·Single cylinder drive, Cable drive.
· Single point manual safety release.
·The primary safety device of automatic machinery and the secondary safety device of cable
breaking in the process of rising ensure the safety of the vehicle.
· Power-side column can be installed at both side, front or rear.
· Non-skid diamond platforms and adjustable safety lock ladders.
· Optional kits:Sliding jack with hand pump, caster kits, plastic oil tray.
MODEL 407-P SPECIFICATIONS
Model
Lifting
Capacity
Lifting
Height
Lifting
Time
Overall
Length
(Inc.
Ramps)
Overall
Width
Overall
high
Width
Between
Columns
Motor
407-P
7000lbs
73 5/8”
1862mm
31S
185 1/2”
4712mm
98 3/4”
2509mm
82 7/8”
2105mm
85 3/8”
2167mm
110V：1.0HP
Fig. 1

2
II. INSTALLATION REQUIREMENT
A.TOOLS REQUIRED
Tape Measure (7.5m) Carpenter’s Chalk
Hammer Screw Sets
Level Bar
Pliers
English Spanner (12")
Lock Wrench
Wrench set：(12＃、13＃、14＃、15＃、17＃、19#
24＃、30#)
B. Equipment storage and installation requirements.
The equipment should be stored or installed in a shady, normal temperature, ventilated
and dry place.
Socket Head Wrench：(3＃、5
＃、6＃、8＃)
Fig. 2

3
≥4”
C. The equipment should be unload and transfer by forklift.
D.SPECIFICATIONS OF CONCRETE (See Fig. 4)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 100mm minimum and without reinforcing steel bars，and
must be dried completely before lift installation.
2. Concrete must be in good condition and must be of test strength 210kg/cm2(3,000psi)
minimum.
3. Floors must be level and no cracks.
E. POWER SUPPLY
The electrical source must be 3.0HP minimum. The source cable size must be 2.5mm²
minimum and in good condition of contacting with floor.
Fig.3
Fig.4
Concrete intensity must be
210kg/cm minimum

4
III. STEPS OF INSTALLATION
A. Check the parts before assembly
1. Packaged lift and Hydraulic Power Unit (See Fig. 5).
2. Open the outer packing carefully, check the parts according to the shipment list.
(See Fig. 6)
3. Take off the drive-thru ramps and columns (See Fig.7).
4. Loose the screws of the upper package stand, take off the offside platform, take out the
parts inside the power-side platform, then remove the package stand.
Shipment
Parts List
parts box
Offside
Platfor
m
Cross
Beam
Power-side
Platform
Fig. 5
Fig. 6
Fig.7
Column
Drive-in
Ramp
Parts
油盘(选购件)
Optional Plastic oil tray

5
5. Move aside the parts and check the parts according to the shipment parts list
(See Fig. 8).
6.Open the carton of parts and check the parts according to the parts box list
(See Fig. 9)
Fig. 8
Fig. 9
62

6
7. Check the parts of the parts bag according to the parts bag list (See Fig. 10).
B. Use a carpenter’s chalk line to establish installation layout as per Table 1
Make sure the size is right and base is flat (see Fig. 11).
Note: Reserve space front and behind the installation site.
MODEL
A
B
C
407-P
3862mm
(152”)
2509mm
(98 3/4”)
4605mm
(181 3/8”)
B
A
C
Use a carpenter’s chalk line to establish
installation layout
Fig. 11
1
2
Fig.10

7
C. Install cross beams (Note that Hole of the beam towards inside and the side
with the rotating component of the safety mechanism should be the same side as
the column where the power unit is installed. See Fig.12 & 13)
Hole towards inside
Fig.12
Fig.13
3
6
The power-side column need
to be installed close to the
rotational safety device.

8
D. Install the Safety Ladders.
1. Take off the pulley safety cover and unscrew a nut of the safety ladders, and then adjust
the four lower nuts to be at the same position. Then install the safety ladder (See Fig. 14).
Fig. 14
Safety Ladder is inserted
between Limited Pins of the
cross-beam
Insert the
safety ladder
from up to
the bottom
between the
Limited Pins
Take off the protective cover
Protective cover
Unscrew A nut
on the safety
ladders.
Safety
Ladder
Limited Pin
Limited Pin