Ampac FireFinder II Series Instruction Manual

FireFinder

INCOMING ALARM CONDITION
1) INDICATION
FIRE LED STEADY
LCD DISPLAY OF DESCRIPTION
TYPE, ADDRESS, DATE TIME
AND NUMBER OF ALARMS
2) SOUNDER SILENCE OR SOUND EVACUATION
PRESS KEY
DISABLE ALARM
REPEAT THE ABOVE STEPS
AFTER PRESSING NEXT TO
DISABLE ALARMS
LCD DISPLAY OF DESCRIPTION
TYPE, ADDRESS, DATE TIME
AND NUMBER OF DISABLES
3) SOUNDER SILENCE
FIRE LED STEADY
IF NECESSARY PRESS TO
SILENCE SOUNDERS
INDICATOR WILL TURN ON
3) RESET ALARMS
PRESS TO RESETALLALARMS
DESCRIPTION
DATE TIME
LOOP No SENSOR No STATUS: ALARM
SENSOR ALARMS 1 OF xx
TYPE
LOOP No SENSOR No STATUS: DIS
DESCRIPTION
DATE TIME
SENSOR DISABLES 1 OF xx
TYPE
FIRE
SOUNDER
SILENCE EVACUATE
DEVICE
DISABLE / ENABLE
SOUNDER
SILENCE
RESET
FIRE

TABLE OF CONTENTS Page No.
1About This Manual..................................................................................................................1
1.1 Introduction................................................................................................................1
1.2 General Requirements ...............................................................................................1
1.3 References.................................................................................................................1
1.4 Symbols.....................................................................................................................1
2System Overview ....................................................................................................................2
2.1 FACP Configuration Examples...................................................................................3
3FireFinder Description............................................................................................................4
4Placing The Basic System Into Operation .............................................................................6
4.1 Unpacking..................................................................................................................6
4.2 Anti-Static Precautions...............................................................................................6
4.3 Working On The System ............................................................................................6
4.4 The Cabinet ...............................................................................................................6
4.5 Mounting The Cabinet................................................................................................6
4.6 Operational Parameters .............................................................................................7
4.7 Cable Types and Limitations ......................................................................................7
4.8 Power Supplies and AC Mains Installation..................................................................8
4.8.1 Connecting the Mains Earth.........................................................................9
4.8.2 Connecting the Mains Power to the Power Supply.......................................9
4.9 Current Limiter, Fuse Board (BRD85CLFB)..............................................................11
4.10 Brigade / PSU Monitor Board (BRD85BPMB)...........................................................12
4.10.1 Battery Connections (TB1).........................................................................14
4.10.2 Auxiliary 27 Volt Power (TB2)....................................................................14
4.10.3 Bell / Sounder Monitored Outputs (TB3 & TB5)..........................................14
4.10.4 Relay Output Connections (TB6 –TB10)...................................................15
4.11 Main Board (BRD85MBA).........................................................................................16
4.12 Front Panel Board (302-690)....................................................................................17
4.13 Main CPU (BRD85CPU)...........................................................................................18
4.14 Slave CPU (302-669) ...............................................................................................19
4.15 Conventional Zone Board (302-671).........................................................................20
4.16 Addressable Loop Termination Board (302-735).......................................................21
4.17 Addressable Loop Termination Board (BRD86DLTB-B)............................................22
5FireFinder Control Panel.......................................................................................................23
6Functions And Menus...........................................................................................................27
6.1 The Default LCD Display..........................................................................................27
6.2 Accessing Functions and Menus ..............................................................................27
6.3 Function Menu and Access Levels ...........................................................................27
7The Main Menu......................................................................................................................28
7.1 Status Menu.............................................................................................................28
7.2 Testing Menu...........................................................................................................30
7.2.1 Alarm Test.................................................................................................30
7.2.2 Fault Test..................................................................................................30
7.2.3 Lamp Test.................................................................................................30
7.2.4 Sounders...................................................................................................30
7.2.5 Printer Menu..............................................................................................30
8Main Functions......................................................................................................................32
8.1 Setting the Function Date Facility .............................................................................32
8.2 Setting the Function Time Facility.............................................................................32

8.3 Setting the Function Daynight Facility.......................................................................32
8.4 Function Logs Facility...............................................................................................32
8.5 The Function Test Facility.........................................................................................33
8.6 Function Manual I/O Control.....................................................................................34
8.7 Function Access (Level II) / Passwords (Level III).....................................................35
8.7.1 Forgotten Passwords.................................................................................35
8.8 Function Programming.............................................................................................35
8.8.1 Conventional Zone Programming...............................................................36
8.8.2 Device Programming.................................................................................37
8.8.3 Input Programming....................................................................................37
8.8.4 Output Programming .................................................................................38
8.8.5 Watchdog..................................................................................................38
8.8.6 Self Learn..................................................................................................38
8.8.7 Extra Devices Detected.............................................................................38
8.8.8 Mismatch Detected....................................................................................39
9Incoming Fire Alarm Signal..................................................................................................40
10 Accessing a Loop, Sensor or Zone......................................................................................41
11 Expanding the FACP with Compatible FireFinder Boards..................................................42
11.1 Ancillary Services.....................................................................................................42
11.2 Compatatible FireFinder Boards...............................................................................42
11.3 16/16 Input / Output Board (302-672) .......................................................................43
11.4 8 Way Relay Board (302-6760/1)..............................................................................43
11.5 16 Way Input Board (302-677)..................................................................................44
11.6 Serial Relay Board (302-732) ...................................................................................44
11.7 32 Zone LED Mimic Board (302-700)........................................................................45
11.8 External Control Interface Board (BRD85ECI) ..........................................................46
11.9 Valve Display Module (302-716)...............................................................................47
11.10 Pump Display Module (302-717)...............................................................................48
11.11 Fire Fan Module (BRD25FCB)..................................................................................49
11.12 Fan Termination Board (BRD25FTB)........................................................................49
11.13 Zone & General Indicator Card (BRD85GIBB)..........................................................50
11.14 Switch and Indicator Card (BRD25GIB –B)..............................................................51
11.15 8 Way Sounder / Bell Monitor Board (302-7420/1)....................................................52
11.16 LED Mimic Board (302-715).....................................................................................53
11.17 Printer......................................................................................................................55
11.17.1 Indicators and Buttons...............................................................................55
11.17.2 Maintenance..............................................................................................56
11.17.3 Printer Connections and Jumpering...........................................................58
11.17.4 Printer 5 Volt Power Supply (BRD42PVCB1).............................................58
12 Expanding the System Through Networking.......................................................................59
12.1 Communications: Network Interface Card (BRD85NIC) ............................................59
12.2 Communications Extender Board (BRD82LTB).........................................................61
12.3 High Level Interface Expander (BRD43SPB)............................................................62
12.4 Expansion Board (302-688)......................................................................................64
12.5 Expansion Controller (159-0077)..............................................................................64
13 SmartTerminal.......................................................................................................................65
13.1 SmartTerminal Controls and Indicators.....................................................................65
13.2 LCD Screen Format .................................................................................................69
13.3 Operation.................................................................................................................71
13.4 Setting the Address..................................................................................................72
13.5 Mechanical...............................................................................................................73
13.6 Installation & Cabling................................................................................................74

13.7 Specifications...........................................................................................................75
13.8 Setting the SmartTerminal Controller Configuration in ConfigManager......................76
13.9 Setting the SmartTerminal Reporting Parameters in ConfigManager.........................76
13.10 Trouble Shooting Chart............................................................................................77
14 RS232 Modem / Programming / Debug Interfacing .............................................................78
15 List of Compatible Devices...................................................................................................79
16 Certification Information.......................................................................................................81
17 Troubleshooting Chart..........................................................................................................82
18 Address Setting ....................................................................................................................83
19 Glossary of Terms.................................................................................................................84
20 Definitions.............................................................................................................................85
21 Quick Reference Guides.......................................................................................................86

Page 1
1 About This Manual
1.1 Introduction
This manual contains all the information required to install, commission and operate the FireFinder
SERIES II Fire Alarm Control Panel (FACP) fitted with Version 6 software and is only available to
and for the use of personnel engaged in its installation, commissioning and operation.
1.2 General Requirements
The FireFinder Series II FACP has been designed and manufactured from high quality commercial
components so as to comply with major world standards. To ensure these standards are not
compromised in any way installation staff and operators should;
Be qualified and trained for the task they undertake;
Be familiar with the contents of this manual prior to the installation, commissioning or
operation of a FireFinder control system;
Observe anti-static pre-cautions at all times; and
Be aware that if a problem is encountered or there is any doubt with respect to the
operational parameters of the installation the supplier should be contacted.
1.3 References
FireFinder Technical Manual
ConfigManager
FireFinder Detector Manual
British Standards:
EN54: Pt’s 2 & 4
1.4 Symbols
Important operational information
Note: Configuration considerations
Observe antistatic precautions
Mains supply earth
DANGER mains supply present

Page 2
2 System Overview
The FireFinder Series II is an Intelligent Analogue / Addressable and / or Conventional Fire Alarm
Control Panel capable of supporting:
Apollo Discovery and XP95 Intelligent Detectors, Multisensor, Photoelectric, Ionisation,
Thermal (heat) and CO detectors and Hochiki range of Detectors.
Addressable Initiating Devices: Modules that monitor any conventional normally open
contact such as supervisory switches and flow switches.
Conventional two wire zone detector circuits
Multiple input/outputs
High Level Interfaces
SmartGraphics
SmartTerminal
Remote LED mimics
Peer to Peer networking
Master Slave (Main - Sub) networking
Main panel plus Data Gathering Panels networking
Panel is built to comply with the following standards:
European Standard: EN54 Part2 & 4 1998
E.O.L
3K3
CONVENTIONAL ZONE
USING CONVENTIONAL DETECTORS
AND BASES
CONVENTIONAL ZONE
CIRCUIT
ADDRESSABLE
LOOP
ISOLATOR
ION OPTICAL HEAT
ANALOGUE DETECTORS MANUAL CALL
POINT ( MCP )
ISOLATOR
E.O.L
6K2
4K7
4K7
FIRE
ALARM
PRESS HERE
TO BREAK
FIRE
ALARM
PRESS HERE
TO BREAK
HIGH LEVEL
INTERFACE /
EV3000
AS PER INPUT 1
AS PER INPUT 1
20K
EOL
4K7
N/O INPUT
SWITCH
RELAY
O/P 1
IN-1
IN-2
IN-3
C1
NC
NO
C2
NC
NO
C3
NC
NO
RELAY
O/P 2
RELAY
O/P 3
FIREFINDER FACP
SINGLE INPUT
DEVICE
FLOW SWITCH
E.O.L 20K
LOOP SOUNDER
L1
L2
E.O.L 10K
SOUNDER
SOUNDER
CONTROL
+
-
+24V DC
N/O C N/C
RELAY
OUTPUT
AUX OUTPUTS
INPUT/OUTPUT
UNIT
CONVENTIONAL DETECTORS
MAXIMUM OF 20
ZONE MONITOR
OUT
IN
SPECIFICATIONS:
MAX LENGTH = 2KM
MAX RESISTANCE = 50ohms
MIN CABLE SIZE = 1.5mm²
MONITORED
INPUT
+
-
+24V DC
THREE INPUT / OUTPUT
DEVICE
E.O.L 20K
ANCILLARY
SERVICES
Figure 1: Typical Application

Page 3
2.1 FACP Configuration Examples
TYPICAL FRONT DOOR LAYOUT FOR A FULLY POPULATED PANEL
NOTE: PANEL LAYOUT MAY VARY DEPENDING ON CLIENT CONFIGURATION
X- MAF (341-0015) CONSISTS OF:
1- CONTROL PANEL BOARD (302-6906)
1- MAIN BOARD (BRD85MBA"X"-A)
1- CPU (BRD85CPU"X"-D)
X-SLAVE CPU (302-6692)
MAIN CONTROL BOARD (BRD85MBA)
20 WAY
10 WAY
FRONT PANEL CONTROL (302-6906)
CN3
CN21
CN20
TH1 CN8
CN1
CN6
D13
D14
CN3
C12
BZ1 CN5
CN2
CN7
CN11
CH16
CH15
CH6 CH8
CH2
CH1
CN16
CN14
CN18
R17
TP3
RN17
RN20
CN4
CN10
CN15
CN13
CN17
c
ba
4 3 2
BRIG ADE I/F
FRON T PANELEXPAN SION LE DS
EXPAN SION PANE L
MODE M
27V IN
PRIN TER
PSU M ONITOR
LOOP C OMMS
1
+
3 WAY
CN1
CN2
1
SLAVE CPU (302-6692)
CH8
CN1
CN2
1
CH8
CN1
CN2
1
16 WAY
SLAVE CPU (302-6692) SLAVE CPU (302-6692)
U15
CN2
a b c
U11
U10
U14
U13
CPU BOARD (BRD85CPU)
PRINTER PSU (302-7130)
C/W CAB2153
26 WAY
CN3
10 WAY
+ -+ -
+ - AUXILIARY
+ BAT -+ IN -DB A/MCP
DOOR SW
BELL2B ELL1
FAULTVALVE MON
BATT FAIL NO C NC NO C NC NO C NC NO C NC NO C NC+ - + - NO C NC + - + -
ALARM ISOLATE
C
SGD II
WARN SYSAUX POWE R O/P
TB10
CN3
TB4
CN2
CN1
TB6
TB5
CN6
TB3
CN5
TB2
BRIGADE
O/P TERM
BOARD
(302-6732)
EARTH
STUD
MAINS
SWITCH
POWER
SUPPLY
UNIT
CABINET BACKPAN VIEW
SHOWING MODULES FITTED
TO THE BACKPAN
AND WIRING DETAILS
TO BATTERIES
TB1 TB2
CN2
CN1
TB3
CTS RTS RXD TXD COM
D ABCS-+ D ABCS-+ COMMS OUTCOMMS IN
OUT
CTS RTS RXD
TXD COM
SCRN
TRX- TRX+
0V +27V
TB3
CN1
TB2
TB1
CN3
OPTIONAL NETWORKING BOARDS
302-7240 NETWORK INTERFACE CARD
302-7250 CONTROLLER INTERFACE CARD.
NOTE: POSITION MAY VARY AS SHOWN
AND IS FOR INDICATION ONLY.
302-7240
302-7250
X- PRINTER
(OEM1447)
C/W MOUNTING
PLATE.
(KIT = 159-0093)
GENERAL INDICATOR, OR
DANGER
240V
FAN CONTROL OR
AGENT RELEASE
CN1CN3
2 LOOP TERMINATION BOARD
(302-7350) OR
16Z CONVENTIONAL BOARD
(302-671B)
L2+ L1-
B
L2+ L1-
AEXT
+35V EXT +35V
L2+ L1-
B
L2+ L1-
AEXT
+35V EXT +35V
SERIAL RELAY
BRD (302-7320) OR
AGENT TERM BRD
(BRD25ATB) OR
FAN TERM
BRD (BRD25FTB)
POWER
CN4
CN2 TX1
POWER
ZD7
CN2 CN1
CN3
MOUNTED ON CONVENTIONAL
OR LOOPTERMINATION BRD
L(AC) N(AC)
-V -V +V +V
(AC)
ACTIVE NEUTRAL
GROUND
-VE +VE
Figure 2: Typical Example of an SP2 Layout
FRONT DOOR AND FRONT INNER DOOR REAR VIEW SHOWING
INSTALLED BOARDS ON FRONT INNER DOOR AND WIRING DETAILS
+ -+ -
+ - AUXILIARY
+ BAT-+ IN-DBA/MCP
DOOR SW
BELL2BELL1
FAULTVALVEMON
BATTFAIL NO C NC NO C NC NO C NC NO C NC NO C NC+ - + - NO C NC + - + -
ALARM ISOLATE
C
SGDII
WARN SYSAUXPOW ER O/P
TB10
CN3
TB4
CN2
CN1
TB6
TB5
CN6
TB3
CN5
TB2
CABINET BACKPAN VIEW
SHOWING MODULES FITTED TO THE BACKPAN
AND WIRING DETAILS
BRIGADE
PSU MON.
BOARD
MAIN CONTROL BOARD
20 WAY
10 WAY
FRONT PANEL CONTROL
TO BATTERIES
2 LOOP TERMINATION BOARD
OR
16Z CONVENTIONAL BOARD
CN8
CN1
CN6
CN5
CN7
CH15
CH2
CN10
BRIGADE I/F
PRINTER
PSU MONITOR
BLANK
3 WAY
3 WAY
SLAVE CPU 4
20 WAY
EARTH
STUD
302-6880 EXPANSION BOARD
TB1 TB2
CN2
CN1
TB3
CTS
RTS
RXD
TXD
COM
D ABCS-+ D ABCS-+ COMMS OUTCOMMS IN
OUT
CTS
RTS
RXD
TXD
COM
SCRN
TRX-
TRX+
0V
+27V
TB3
CN1
TB2
TB1
CN3
OPTIONAL NETWORKING BOARDS
NETWORK INTERFACE CARD
CONTROLLER INTERFACE CARD.
NOTE: POSITION MAY VARY AS SHOWN
AND IS FOR INDICATION ONLY.
16 WAY
NETWORK
I/F CARD
SLAVE CPU 3
SLAVE CPU 2
SLAVE CPU
6
NOTE: WIRING MAY VARY DUE TO
CLIENT PANEL CONFIGURATION
CH15
CONTROLLER
I/F CARD
CPU BOARD
SLAVE CPU
7
SLAVE CPU
8
MAINS
INPUT
16Z CONVENTIONAL BOARD
CABINET (291-0076)
L(AC) N(AC)
-V -V +V +V
(AC)
POWER
SUPPLY
UNIT
ACTIVE NEUTRAL GROUND -VE +VE
ANCILLARIES or
HOUSING BLANKS
AGENT RELEASE
MODULE OR
FIRE FAN CONTROL
MODULE
CN1CN3
AGENT TERM
BRD OR
FAN TERM
BRD
ZD7
CN2
RJ45/8 PIN
RJ45/8 PIN
MAINS
SWITCH
DAN GER
240V
GENERAL
INDICATOR
CARD
X- PRINTER
(OEM1447)
C/W MOUNTING
PLATE.
(KIT = 159-0093)
BLANK
SLAVE CPU
5
Figure 3: Typical Example of an SP8 Layout

Page 4
3 FireFinder Description
The following description does not relate to specific cabinets as the size of each cabinet will vary
with the amount of hardware fitted.
The heart of the FireFinder Series II consists of two boards collectively known as the Controller.
These boards are the Main Board (BRD86MBA) and the CPU board (BRD86CPU). Combining these
two boards with a front panel forms the basis for a FireFinder Series II FACP. A single Controller
without an expansion board has the capacity to interface to four (4) Slave CPU’s modules. Each of
these Slave CPU’s can interface to 16 Zone Conventional Termination Boards, Loop Termination
Boards or Input/Output Boards as well as communicate with the Brigade / PSU Monitor Board.
The Main Board has the Slave CPU Board for the first Loop Termination Board and the provision for
mounting of up to three additional Slave CPU’s. The Slave CPU’s all have the same software
installed and the manner in which they operate is automatically determined by the type of termination
or interface board onto which they connect.
If the system is to be expanded to have more than four Slave CPU’s an Expansion Board is required.
This board contains Slave CPU No. 5 and expansion sockets for three more. This configuration
allows for a maximum number of 8 Slave CPU’s that any one Controller can accommodate.
If a system is required to be expanded beyond eight Slave CPU’s then either local networking using
up to a total of four controllers (max 32 Slave CPU’s) within the one cabinet may be fitted or external
networking must be used.
The FireFinder Series II has an internal ASPI (Ampac Serial Peripheral Interface) serial bus. This
serial bus provides interfacing to the Brigade /PSU Monitor Board and if required up to eight (8)
Sounder Board/s.
FireFinder Series II has a second serial interface that connects to ancillary boards these can be
used to control and monitor field plant equipment or the addition of an agent release module.
Where the system design exceeds the capability of one FireFinder Series II then other FireFinder
Series II panels can be networked together to provide an expanded system containing multiple
boards in a variety of applications.
Some of these applications include:
A Master / Slave (Main Sub) FACP arrangement (MFACP / SFACP)
A Peer to Peer System
Use of Data Gathering Panels (DGP’s)
SmartTerminal
SmartGraphics
A Network FireFinder Series II System supports a combination or all these options on a single
network. Each panel on the network is regarded as a “node”. The NETWORK BUS is accessed
using a Network Interface Card. The network configuration determines whether a NIC is required.
Configurations can be;
Master / Sub FACP:Where there is one or more FACP’s configured as local panels then each
report the status of their associated zones/devices to a MFACP. There is no control between local
panels as the MFACP is structured to have full control of the entire system.
Peer to Peer:Each FACP is regarded as a Master FACP and therefore a user can take control of
the entire fire system from any FACP.
Data Gathering Panel:The use of this type of panel may be installed where there is a need to have
field terminations only at one location and all control is performed by an FACP that is remotely
located.
SmartTerminal: Provide the user with the ability to monitor the status of designated areas or an
entire site as well as execute specific interrogation tasks.
SmartGraphics: Is an active graphics system connected to the FireFinder Series II.

Page 5
MAIN CPU
27VDC
(CN16)
IN
302-6692 302-6692 302-6692
EXTERNAL LOOP
COMMUNICATION
CONNECTS TO
NIC OR CIC
#2 UP TO 3 ADDITIONAL
SLAVE CPU's (302-6692)
CAN BE SLOTTED ONTO
THE MAIN BOARD.
TO CN5 OF THE
BRIGADE BOARD
OR SOUNDER
CONTROL BRD
IN CN1
INTERNAL PRINTER
OUTPUT
TO FRONT KEYPAD
(NOT USED IF THE
PANEL IS A DGP OR
SLAVE CONTROLLER)
INTERNAL SERIAL
COMMUNICATION
PORT
MODEM
I/O PORT
THE MAIN BOARD
CARRIES
SLAVE CPU 1.
CN10 CABLES VIA
A 20 WAY CABLE
TO THE PANEL
BOARDS
AN EXPANSION BOARD (302-6880) CAN BE CONNECTED
TO FACILITATE UP TO 4ADDITIONAL MODULES IF REQUIRED
302-6692 302-6692 302-6692
UP TO 3 ADDITIONAL
SLAVE CPU's ( 6, 7 & 8 )
CAN BE SLOTTED INTO
THE EXP BOARD.
CN2 CN2 CN2
CN2 CN2
CN2
MAIN BOARD
LOOP COMMS
CN11
302-6880 JUN 98
CN1 CN2 CN3 CN4
SW3
CN17
CN16
CN7
CN2 CN1
CN8
NODE ADDRESS
PRINTER
BACKLIGHT
EXPANSION
PANEL
EXPANSION
LEDS
FRONT PANEL CN6
#1 PANEL BOARDS
ARE CONNECTED
VIAA 20 WAY
RIBBON TO CN1
ON A SLAVE CPU
SLAVE CPU 2
SLAVE CPU 3
SLAVE CPU 4
SLAVE CPU 6 SLAVE CPU 7 SLAVE CPU 8
PANEL BOARDS ARE
CONNECTED BY A 20
WAY RIBBON TO CN1
ON A SLAVE CPU
CN1 CN1
CN1
CN1 CN1 CN1
CN4
CN3
CN5
CN2
CN1
+ -
+-
CN5
CN10 CN7
CN18
RESET
SW1
BZ1
LK2
BUZZER
ENABLE
KEY
SW
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
a b c
ON
1 2 3 4 5 6 7 8
CN21
CN20
RS485 COMMS TO
BACKPAN BORADS
RS485 COMMS TO
FRONT PANEL MODULES
Figure 4: Single Controller Board with Expansion Board

Page 6
4 Placing The Basic System Into Operation
4.1 Unpacking
Carefully unpack the FireFinder.
The package should include:
FireFinder SERIES II Fire Alarm Control Panel
An Operators manual
003 keys
4.2 Anti-Static Precautions
To prevent damage to components, modules and boards, anti-static precautions MUST be observed
while performing any task within the FACP. The same applies to those situated in the field
4.3 Working On The System
Prior to unplugging any connector, connecting or disconnecting any wiring, removing or replacing
any module or board, ensure that both the Mains and Batteries have been isolated to prevent
damage to panel components.
4.4 The Cabinet
Features:
The cabinet is available in four different styles. Each style has the capability of being either
surface or flush mounted. With flush mounting though a surround is required.
Normally painted Arch White Ripple. Other colours are available on request.
The inner and outer door hinges are mounted on the left-hand side of the cabinet which
allow the doors open to an angle of 100º. Locking is normally keyless though keyed entry is
available on request.
Knockouts are positioned at the top and rear of the cabinet to simplify cable entry. The larger
range of cabinets use a removable gland plate to allow for the greater amount of cabling
4.5 Mounting The Cabinet
Note: It is recommended the cabinet should be installed in a clean, dry, vibration-free area.
Open the front door. Use the keyhole mounting holes in the top corners and in the lower middle of
the unit to mount it on the wall. Cables to connect the system to its external actuating devices are
brought in through the knockouts on the top or bottom of the cabinet.
R 6mm.
12 mm
Tap lightly around the
rim of the knockout
3 mm
Figure 5: Example SP1 Back Pan Mounting Hole & Removing Knockouts

Page 7
4.6 Operational Parameters
GENERAL
Max No of Devices per Loop
126
Max No of Devices per Conventional Zone
32
Cable Loop Characteristics
2 core. 1.5 to 2.5mm²
POWER SUPPLY
Power Supply Output Voltage
27.4V
Power Supply Output Current
2Amp, 5.6Amp or 18Amp
Power Supply Input
85 - 264VAC (47 –63Hz)
Panel Current Draw
220 mA (min)
Minimum Operating Voltage
19.2 V
Battery Type & Capacity
Note: A greater range of batteries can be
supplied if using a remote battery cabinet
2 x 12V sealed lead-acid
SP1,2 & M = 12AH
SP4 = 24AH
SP8 = 24AH
ENVIROMENTAL
Temperature
-5ºC to + 55ºC
Humidity
25% to 75%
IP Rating
IP51
MECHANICAL
Material
1.2mm Steel
Finish
Arch White Ripple Coat
Dimensions
495mm (H) x 397mm (W) x 125mm (D)
Dimensions
450mm (H) x 400mm (W) x 130mm (D)
Dimensions
420mm (H) x 515 mm (W) x 140mm (D)
Dimensions
840mm (H) x 515mm (W) x 140mm (D)
4.7 Cable Types and Limitations
All System wiring should be installed in accordance with the national wiring regulations where the
panel is being installed.
To comply with EMC (Electro Magnetic Compatibility) regulations and to reduce the risk of electrical
interference in the system wiring, we recommend the use of Fire-resistant screened cables
throughout the installation, examples of which include the following:
Manufacturer
Cable Type
CoreSize (mm2)
1
1.5
2.5
Ventcroft*
No Burn Platinum



Ventcroft
Diamond



Prysmian cables & systems Ltd
FP200 Gold LSOH



Prysmian cables & systems Ltd
FP Plus



AEI Cables Ltd
Firetec Multicore LSZH



CAvicel SpA
Firecel SR/114H



Tratos Cavi SpA
FIRE-Safe TW950



Eland Cables
FireForce



Draka
Firetuf (OHLS)



Draka
Firetuf Plus



* For LPCB approval the panel was tested with Ventcroft No Burn Platinum 1.5mm2 cable.

Page 8
4.8 Power Supplies and AC Mains Installation
Generally the AC Mains will be connected to either a 2 Amp, 5 Amp or 18Amp 27 volt supply. These
supplies will be either mounted in the upper or lower right hand corner of the cabinet with the
Brigade Board mounted above or below. The wiring should enter the cabinet through the nearest
knockout entry hole on that side. See the following diagrams for the actual wiring and fusing details
for each supply.
Common Power Supply Features & Specifications
High efficiency, low working temp.
High efficiency; low ripple noise
Universal AC input/ full range
Soft start with limiting AC surge current
Short circuit/ over load
Built in EMI Filter and PFC Circuit
Remote control on/off (option)
Over voltage protection
Over temp. protection (option)
Input Voltage:
85 to 264 VAC
Tolerance at 27V
+/- 1%
Input Freq
47 to 63Hz.
Load Regulation
+/- 0.5%
PFC
0.95~230VAC
Line Regulation
+/- 0.5%
Power Supply Specifications
Type No
Output
Tolerance
R & N
Efficiency
S-60-27
27V @ 2.2A
1%
150mV
79%
SP-150-27
27V @ 5.6A
1%
150mV
84%
SP-500-27
27VDC @ 18A
1%
200mV
86%

Page 9
4.8.1 Connecting the Mains Earth
All earth cabling shall be terminated to the panel Chassis Earth Terminal in a star configuration.
The earth cable closest to the cabinet body shall have an M4 SPW beneath the lug then an M4 SPW
and M4 nut.
Each additional earth cable shall be terminated with an M4 SPW and M4 nut.
An additional M4 nut and M4 SPW are fitted to the Chassis Earth Terminal for installers to connect
their Mains Earth.
M4 Shake Proof Washer
M4 Shake Proof Washer
CHASSIS EARTH TERMINAL
M4 Nut
Earth Cable
Earth Cable
M4 Nut
M4 Shake Proof Washer *
M4 Nut *
Note:
* Extra M4 Nut and M4 SPW are
provided finger tight on the Earth bolt.
Figure 6: Panel Earthing
4.8.2 Connecting the Mains Power to the Power Supply
Terminate the mains power to the 240 VAC switch terminal block as shown below.
2 AMP Power Supply
Output Voltage: is set to 27.4Volts.
Mains cable should be no less than 0.75mm
POWER SWITCH
(LOOKING AT REAR)
MAINS CORD BROWN
(ACTIVE)
BLUE
(NEUTRAL)
BROWN
(ACTIVE)
LED
TO CHASIS EARTH
TERMINAL
DC 27V TO PANEL
EARTH (GREEN)
L(AC)N(AC)GNDV-V+
V ADJ
C
1
LOOP
Figure 7: Mains Power Connection 2 AMP Power Supply

Page 10
5 AMP Power Supply
Output Voltage: is set to 27.4 Volts.
Mains cable should be no less than 0.75mm
TO CHASSIS EARTH
TERMINAL 27VDC TO BRIGADE
PSU MONITOR BOARD
EARTH (GREEN)
V ADJ
L(AC) N(AC) -V -V +V +V
+
(AC)
BLACK
RED
MAINS CORD BROWN
(ACTIVE)
BLUE
(NEUTRAL)
Fuse is under this cover
POWER SWITCH
(LOOKING AT REAR)
C
1
LOOP
Figure 8: Mains Power Connection to the 5 AMP Power Supply
18 AMP Power Supply
Output Voltage: is set to 27.4 Volts.
Mains cable should be no less than 0.75mm
LOOP
BROWN
(ACTIVE)
DC 27V TO BRD85CLFB
V ADJ
(AC) (AC)
+
(AC)
BLACK
RED
+27V 18A+S -V -S
L N
( AC ) FG NC NC GRC
TO CHASSIS EARTH
TERMINAL
EARTH (GREEN)
MAINS CORD
BLUE
(NEUTRAL)
POWER SWITCH
(LOOKING AT REAR)
1
C
F5
F4F3
F2F1
CN5
CN4
CN3
CN2CN1
HS1
TB1
TB4
Q3
Q1 Q2
RV1
U2
U1
N1236
BRD85CLFB
1A 1A 1A 1A 1A
+ OUTPUT - + BATT - + PSU I/P -
0V CN1-5 PINOUT = 0V, +27V, 0V
0V+27V 0V
+27V 0V
BRD85CLFB
Figure 9: Mains Power Connection to the 18 AMP Power Supply C/W Current Limit Board

Page 11
4.9 Current Limiter, Fuse Board (BRD85CLFB)
The Current Limiter, Fuse Board provides protection for the boards, cards and other 27VDC
distribution within the FACP when the 18Amp power supply is used. The four LED’s associated with
the board indicate that 27VDC is available at each of the outputs CN1 –5.
F5
F4F3
F2F1
CN5
CN4
CN3
CN2CN1
HS1
TB1
TB4
Q3
Q1 Q2
RV1
U2
U1
N1236
BRD85CLFB
1A 1A 1A 1A 1A
+ OUTPUT - + BATT - + PSU I/P -
TO
BRD85BPMB
TB1
+27V
0V
+BATT V
CN1-5 PINOUT = 0V, +27V, 0V
0V+27V 0V
+27V 0V
TO
BRD85BPMB
CN1
MAF, FRONT DOOR
AND BACKPAN
DISTRIBUTION
DISTRIBUTION
EV60 / 120 TONE GEN
(Not Current Limited)
Figure 10: Current Limiter Fuse Board

Page 12
4.10 Brigade / PSU Monitor Board (BRD85BPMB)
The Brigade / PSU Monitor Board monitors and controls the power supply, battery charging,
monitored / un-monitored inputs, outputs and the 7 relay outputs.
Providing the Power supply has adequate capacity, monitored Bell/Sounder O/P’s are capable of
driving 2 X 2Amp circuits. Each circuit terminated in a bell/sounder or not, requires a 10KΩEOL
resistor to give a system normal indication if monitoring is enabled in ConfigManager. If either circuit
is open or shorted, the panel buzzer will sound and a Sounder Fault will be indicated on the Panel.
Monitoring is achieved using a small reverse polarity current. For this reason it is necessary to
ensure that all alarm devices are fitted with a series diode (1N4004 recommended) and correct
polarity is observed for both the output and the sounders they are connected to.
Relay outputs marked NO, C and NC are voltage free relay contacts. Outputs marked +ve and -ve
are fitted with resistors (10KΩ) to allow the circuit to be monitored. If these outputs are un-used they
must be terminated at the terminal block or turned off in ConfigManager.
For all outputs combined, total output current is 2A (if 2A power supply is being used).
Once all the field devices are installed and the wiring has been correctly terminated the FireFinder™
is ready to turn on. Turn the Mains power on, and connect the batteries observing correct polarity.
The green power on LED should be illuminated.
OUTPUT RATINGS
TB
Function
Type of Output
Fuse
Relay
3
Sounder 1.1
2 Amp Fused
F2
RL 1
Sounder 1.2
2 Amp Fused
F3
RL 1
4
F.A.R.E Monitored
1 Amp Fused
F4
F.A.R.E Non-Monitored
1 Amp Voltage Free Contacts
RL2
5
Sounder 2 Monitored
1 Amp Fused
F5
Spare Non-Monitored
1 Amp Voltage Free Contacts
RL3
6
F.W.R.E Monitored
1 Amp Fused
F6
F.W.R.E Non-Monitored
1 Amp Voltage Free Contacts
RL 4
7
Disable
1 Amp Voltage Free Contacts
RL 6
8
Alarm
1 Amp Voltage Free Contacts
RL 5
9
Valve Monitor
1 Amp Voltage Free Contacts
RL 8
10
Batt Fail
1 Amp Voltage Free Contacts
RL 7
1
Battery Output
Thermistor Protected
2
Aux Power Output
1 Amp Fused Not Monitored
F7
Aux Power Output
1 Amp Fused Not Monitored
F8
Fuse Information
1. All fuses are of the Glass M205 style.
2. F1 is 6.3A
3. Voltage Free contacts are rated at 1A @ 30V
Back EMF Protection
Inductive loads fitted to the Brigade PSU Monitor Board MUST be fitted with
“Flyback”diodes at the load for back EMF protection.
Transient Protection
Recognised transient line protection methodologies at the FACP and the load MUST
be considered when connecting any control devices to the outputs be they in close or remote
to the FACP.

Page 13
Aux
Power
O/P
Disable Relay
Alarm Relay
NO C NC
+ -+ -
NO C NC
Batt Fail Relay
Valve Mon Relay
+ IN - + BAT -
302-6730
+ -
F6
RL4
TB2
CN5
TB1
RL7
RL5
RL6
CN6
TB6
CN1
CN2
RL8
TB11
F1
6.3A
CN3
TB8
TB7
TB10
TB9
///
NO
NC
C
RL1
RL2
+ -
F.W.R.E.
NO C NC
+ -
NO C NCNO C NCNO C NC
To CN7 of the Main
Controller Board
- + -- + -- + -
CN1, 2, 3 Supplies
Regulated +27VDC
to Internal Boards
+27VDC
from PSU
Note: NC C NO
Denotes Voltage
Free Contacts
NC = Normally Closed
C = Common
NO = Normally Open
TB4
TB5
Monitored
Un-monitored
Monitored
EOL
Required
EOL
Required
Monitored
EOL
Required
Monitored
EOL
Required
C
NC
NO
NO C NC
Un-monitored
Un-monitored
Not Used
Sndr 1.2
Sounder 1.1
++
-
TB3
EOL
10K
Ohms
EOL
10K
Ohms
Sounder 2
Sounder 2
F.A.R.E.
Door Switch DBA
MCP
Battery 2
12Volts
Battery 1
12 Volts
+--
+
-
F3 2A
Sounder 1.2
Sounder 1.1
F2 2A
F4 1A
F.A.R.E. Mon.
Sounder 2
F5 1A
F8 1A
F7 1A
Aux Power
O/P 1 & 2
1A
F6
Figure 11: Brigade / PSU Monitor Board Layout
Note: When connecting to the Brigade PSU Monitor board transient and “Flyback” (Back EMF)
protection methodologies MUST be applied.

Page 14
4.10.1 Battery Connections (TB1)
A FireFinder requires two (2) 12 volt batteries. The batteries should be placed into the bottom right
hand side of the cabinet. A red and black lead coming from TB1 on the Brigade Board will be clearly
seen in the same area, this lead is to be connected to the batteries red to positive and black to
negative once the system is operating on Mains supply. Battery size is dependant on system
configuration and can vary from 12 AHr to over 100 AHr.
+27VDC
FROM PSU
TB1 is located on the bottom
right hand side of the board
Brigade/PSU
Monitor Board
Battery 2
12Volts
Battery 1
12 Volts
+--
+
TB1
C14
M20
+ BAT -+ IN -
Figure 12: Battery Connections to the Brigade / PSU Monitor Board
4.10.2 Auxiliary 27 Volt Power (TB2)
Two (2) 1 Amp outputs are available from TB2 terminals 1+ (plus) and 2- (minus) or 3+ and 4- on the
Brigade Board. It is important to note these outputs are not monitored.
2 X FUSED 1A
AUX POWER
OUTPUTS
TB2 is located in the middle of the
left hand side of the board
Brigade/PSU
Monitor Board
C27
TB2
+ -
1A
1A
+ -
F7
F8
Figure 13: Auxiliary 27VDC Power Output
4.10.3 Bell / Sounder Monitored Outputs (TB3 & TB5)
Sounders are connected to the Brigade / PSU Monitor Board as shown below. If more sounders are
required, the Sounder / Bell Control Board (302-7420) must be used.
Bell/Sounder 1
Bell/Sounder 2
TB3
Brigade/PSU
Monitor Board
EOL
10K
Ohms Un-used O/P's must
be terminated in
10K Ohms EOL
+ - + -
TB3 is located on the top
left hand side of the board
1N4004
or similar
Note:
Outputs are fused @ 2Amps ( F2, F3 )
& monitored
Figure 14 Connecting a Bell / Sounders TB3
F.A.R.E.
TB5
TB4
Brigade/PSU
Monitor Board
EOL
10K
Ohms
Warning
System
EOL
10K
Ohms
NO C NC
+ -
NO C NC
+ -
TB4 & 5 are located on the top
left hand side of the board
Note:
1. NO C NC are 1A voltage free contacts
2. + / - are monitored / fused 1A outputs
Un-used O/P's must be terminated in
10K Ohms EOL
Fused by F5
& monitored
Fused by F4
& monitored
Figure 15: Connecting a Bell / Sounders TB5

Page 15
4.10.4 Relay Output Connections (TB6 –TB10)
The relay contacts are connected as shown below.
Brigade/PSU
Monitor Board
TB10 TB9 TB8 TB7 TB6
TB10 to TB6 are located on the
lower left hand side of the board
CNC
NO
1A Un-monitored
Voltage Free Conacts:
NO: Normally Open
NC: Normally Closed
C: Common
NO C NC
NO C NC
NO C NCNO C NC
NO C NC NO C NC NO C NC NO C NC NO C NC
+ -
F.W.R.E.
DISABLE
ALARM
VALVE MON
BATT FAIL
M23 M27 M26 M24
+ -
= 1A Fused monitored
output F6 must be
terminated in EOL
EOL
10K
Ohms
Note 1:
Note 2:
Figure 16: Relay & F.W.R.E. Outputs