AMX FG1010-37 User manual

Quick Start Guide
AutoPatch CAT-5 S-Video+Stereo TX & RX
Overview
The CAT-5 S-Video+Stereo TX (Transmitter) and RX (Receiver) are designed to
distribute video and audio over CAT-5 (5e, or 6). The TX and RX are available as
modules or as AF-10 boards, which can be mixed or work in conjunction with
S-Video+Stereo CAT-5 boards on an AMX AutoPatch Distribution Matrix. This guide
contains complete information for use as a standalone end-to-end solution. For use
with a distribution matrix, see the distribution matrix’s instruction manual on the AMX
AutoPatch Software & Documentation CD or visit www.amx.com.
Due to the wide variety of connector options available, the illustrations in this guide
may differ from the model you ordered. Connector options include BNC, RCA, or
S-Video for video and 3-position terminal block (balanced or unbalanced) or RCA
(unbalanced) for audio. For module and board model numbers, see tables on reverse.
Specifications
System Setup
The example in FIG. 1 illustrates an AF-10 TX board used in conjunction with an
RX Module.
Module and/or AF-10 Board Installation
Adjusting for Cable Length
If the length of the CAT-5e cable between the RX and TX does not match the length
specified for the factory default setting of <175 ft. (53 m), an adjustment is required
and must be done before the connectors are attached. Use the DIP switch settings
from the table below when making the adjustment.
Tip: Gain adjustments can be made on the RV1 and RV2 potentiometers while the top
plate is off the RX Module or while the RX board is out of the AF-10.
ESD Warning: Avoid ESD (Electrostatic Discharge) damage to sensitive
components; be sure you and the equipment are properly grounded before
touching any internal materials.
To adjust an RX module for cable length:
1. Remove the screws on each side of the RX (four screws total).
2. Remove the right screw on the rear plate (the end with the connectors) and the
left screw on the front plate of the RX. (Do not remove the left screw on the rear
plate or the right screw on the front plate.)
3. Gently lift the top plate off the RX.
4. Set toggles (1-2-3-4) on both DIP switches (a small screwdriver or paper clip
works well) to the correct position according to the table above. Both DIP
switches must be set to the same value.
5. Replace the top plate; insert screws and tighten until snug.
General Specifications
Approvals CE, UL, cUL
Signal Types S-Video (or composite on one BNC or RCA) & stereo audio
Supported Cable Types CAT-5, CAT-5e, CAT-6
Power Consumption (max.)
& Connector – Module 9 VDC, 500 mA
2.1 mm DC power jack
Power – AF-10 120 VAC / 240 VAC
Humidity 0 to 90% non-condensing
Operational Temperature 32° - 110° F (0° - 43° C)
Dimensions – Module 5.22 in. (13.26 cm) depth
5.82 in. (14.78 cm) width
1.42 in. (3.61 cm) height w/out feet
Weight – Module Approximately 1.5 lb. (0.68 kg)
Video Specifications
Video Bandwidth All distances up to 1000 ft.(305 m) (+/-3 dB) 10 MHz (min.)
Video Crosstalk f = 5 MHz <-70 dB
TX Level (max.) +/-2 V
TX Impedance 75 ohms
RX Level (max.) +/-2 V
RX Impedance 75 ohms
Audio Specifications
Unbalanced Version
Audio THD + Noise f = 20 Hz to 20 kHz, Vin = -10 to +8 dBu <0.01%
Balanced Version
Audio THD + Noise f = 20 Hz to 20 kHz, Vin = +4 to +22 dBu f = 20 Hz to 20 kHz, Vin = -10 to +22 dBu <0.01% <0.04%
Unbalanced Version
Audio Crosstalk f = 1 kHz, Vin = +2 dBu <-90 dB
Balanced Version
Audio Crosstalk f = 1 kHz, Vin = +20 dBu <-90 dB
TX Level (max.)
Standard (unbalanced):
High Headroom (balanced): +8 dBu +22 dBu
TX Impedance 18 kohms
RX Level (max.)
Standard (unbalanced):
High Headroom (balanced): +8 dBu +22 dBu
RX Impedance 50 ohms
FIG. 1 Typical system setup
Line Length Adjustments
CAT-5e Cable Length DIP Switch Setting for Toggles 1-2-3-4
<175 ft. (53 m) 0-0-0-0
176 to 400 ft. (54 to 121 m) 1-0-0-0
401 to 450 ft. (122 to 137 m) 0-1-0-0
451 to 550 ft. (138 to 167 m) 1-1-0-0
551 to 650 ft. (168 to 198 m) 1-0-1-0
651 to 699 ft. (199 to 213 m) 0-1-1-0
700 to 800 ft. (214 to 243 m) 1-1-1-0
801 to 900 ft. (244 to 274 m) 0-0-0-1
901 to 950 ft. (275 to 289 m) 1-0-0-1
951 to 1000 ft. (290 to 305 m) 1-0-1-1
FIG. 2 Remove screws indicated & lift top plate
FIG. 3 Set toggles on both DIP switches to the same value
2 3 4
0
2 3 4
0
2 3 4
0
Example shows a setting
of “0-1-0-0” for a cable length
of 425 ft. (130 m)
The “1” side
The “0” side
120VAC/240VAC
25 Watt/ 2A Max.
DVD
TX Board in AF-10
Source Device
Up to 1000 ft. (305 m) Monitor
RX Module

For full warranty information, refer to www.amx.com.
6/07
©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax [phone] • technical support 800.932.6993 • www.amx.com
93-40-813 REV: A1
To adjust an AF-10 RX board for cable length:
1. Remove the screws at the top and bottom of the board’s faceplate.
2. Push down on the board extractor handle and pull the board out.
3. Set toggles (1-2-3-4) on both DIP switches (a small screwdriver or paper clip
works well) to the correct position according to the table on the previous page.
Both DIP switches must be set to the same value.
4. Push the board back into position (handle will snap into place); replace screws.
Installation
Important: Always use a UL approved power source. Check the power source’s
documentation for information specific to that power source.
To attach connectors & power to the TX and RX:
1. Adjust the RX forline length if necessary (see previous procedure for RX cable
length adjustment).
2. Insert, attach, or wire the connectors to the TX and RX as shown in FIG. 5 and
FIG. 6 or 7.
3. Insert the RJ-45 connector into the CAT-5 receptacle (see FIG. 5).
4. Module – Plug power cord into the power jack and into the power source.
AF-10 – Plug power cord into the power receptacle and into the power source.
Video Connectors
Video connectors are available in BNC, RCA (video not shown), or S-Video.
Note: AMX AutoPatch S-Video cables lock onto S-Video connectors. Standard
S-Video cables may be used, but will not lock. Hold the connector at a slight angle to
the right while pushing in or pull back on the connector housing while pushing in.
Audio Connectors
Audio connectors are either 3-positionterminal block (balanced/unbalanced – FIG. 6;
unbalanced – FIG. 7) or RCA (unbalanced – FIG. 5).
Important: To determine the correct wiring to use for the audio connectors, check
the type of connection specified in the tables in the column to the right. If the model is
listed for balanced audio, it may also be wired for unbalanced audio (FIG. 6). If the
model is listed for unbalanced, it can only be wired for unbalanced (FIG. 7).
Note: When using twisted-pair wire, connect the shield (ground) at one end only
(recommend receiving end) to minimize low frequency noise.
TX & RX Model Numbers
* High headroom – up to a +22 dBu signal.
FIG. 4 Set toggles on both DIP switches to the same value
FIG. 5 Insert or attach video connectors as shown in sample boards
FIG. 6 Wiring for models with 3-position balanced audio connectors (see tables to right)
FIG. 7 Wiring for models with 3-position unbalanced audio connectors (see table below)
2 3 4
0
2 3 4
0
2 3 4
0
Example shows a setting
of “0-1-0-0” for a cable length
of 425 ft. (130 m)
The “1” side
The “0” side
RJ-45 RJ-45
BNC S-Video
RCA
Audio
(see below)
FG1040-443 FG1040-413
(audio)
Signal
Jumper
Common
Non-Inverting Sign
al
Inverting Signal
Shield Balanced Wiring
Unbalanced Wiring
Signal
Commo
n
Unbalanced Wiring
CAT-5 S-Video+Stereo TX & RX Modules
FG1010-37 TX, S-Video / RCA unbalanced
FG1010-43 TX, S-Video / 3-position unbalanced
FG1010-49 TX, BNC / RCA unbalanced
FG1010-55 TX, BNC / 3-position unbalanced
FG1010-61 TX, RCA / RCA unbalanced
FG1010-64 TX, BNC / 3-position balanced (HH)*
FG1010-03 TX, S-Video / 3-position balanced (HH)*
FG1010-34 RX, S-Video / RCA unbalanced
FG1010-40 RX, S-Video / 3-position unbalanced
FG1010-46 RX, BNC / RCA unbalanced
FG1010-52 RX, BNC / 3-position unbalanced
FG1010-58 RX, RCA / RCA unbalanced
FG1010-67 RX, BNC / 3-position balanced (HH)*
FG1010-00 RX, S-Video / 3-position balanced (HH)*
CAT-5 S-Video+Stereo TX & RX AF-10 Boards
FG1040-410 TX, RCA / RCA unbalanced
FG1040-413 TX, S-Video / RCA unbalanced
FG1040-416 TX, S-Video / 3-position unbalanced
FG1040-419 TX, BNC / 3-position unbalanced
FG1040-422 TX, BNC / RCA unbalanced
FG1040-440 TX, S-Video / 3-position balanced (HH)*
FG1040-443 TX, BNC / 3-position balanced (HH)*
FG1040-425 RX, RCA / RCA unbalanced
FG1040-428 RX, S-Video / RCA unbalanced
FG1040-431 RX, S-Video / 3-position unbalanced
FG1040-434 RX, BNC / 3-position unbalanced
FG1040-437 RX, BNC / RCA unbalanced
FG1040-446 RX, S-Video / 3-position balanced (HH)*
FG1040-449 RX, BNC / 3-position balanced (HH)*