amzchef ZM1507 User manual

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY
RETAIN THIS MANUAL FOR FUTURE REFERENCE
ZM1507
220-240V 50/60Hz 150W

14
16
18
18
20
21
23
25
26
29
31
33
33
34
2

36
38
40
41
44
46
48
48
49
51
53
55
56
59
61
63
63
64
3

66
68
70
71
74
77
78
78
79
4

5

6

7

No. Part name Function
Power cordIt is used for connecting the power supplyto provide power.
Main bodyAs a main part and the power source of the appliance,
Power switch It controls the operating statuses of the appliance.
LockingButton It is used for locking the drum to prevent it from getting
loose from the main body during use.
8

Drum
It isa main part for juicing. Food ingredients are loaded from the
Feed Chute at the top and then discharged in forms ofjuice and
pulp via the juice outlet and the pulp outlet respectively.
Juice strainer By means of breaking in with the Auger, it is used for grinding
and filtering the extracted food ingredients toget juice
Auger
As a main partfor juicing,it is used for conveying food
ingredients and grinding thembybreaking in with the
juice strainer or the squeezer.
End capIt isused for grinding food ingredients bybreaking in with the
Auger(For fruitsand vegetables).
Juice container It isused to hold and collect juice.
Pulp container It isused for loading Pulps.
Plunger
It isused for squeezing the fed food ingredients gently for
their full contact with the auger and higher juice extraction
efficiency.
9

Switch operation instructions:
“SOFT”: it is used for juicing soft food
ingredients.
“HARD”:it is used for juicing hard food
ingredients.
“0” : Close and stop
“Rev” : It is used when pulp discharge
blocked or the motor is locked
10

Connect the juicing body and the
main body:1.Have the triangular
aligning sign “▼” on the juicing
body align with the aligning
“unlocking triangular sign” on the
main body and then put the juicing
body into the main body (the three
clips on the juicing body will realize
alignment).Then turn the juicing
body anticlockwise. When there is
a click, it suggests that the
connection is finished.
Have the hexagonal shaft of the Auger
align with the hole on the main body and
push it horizontally until it reaches the
bottom (when alignment fails, just turn
the Augers lightly).
Fit the larger-hole end of the juicer
strainer into the tail of the Auger and
push it while the three clips of the juicer
strainer align with the three clamping
slots in the drum. (The juice strainer is
used with the juicing button in the rear
only. This function is used for juicing.)
11

Place the end cap onto the drum
by aligning the triangle alignment
mark “▼” on end cap with the
unlock triangle mark on the drum,
and then rotate the end cap
counter clockwise.
Put the Juice container in the
corresponding groove on the
main body and have its opening
align with the bottom of the juice
outlet of the drum.
Put the pulp container below the
pulp outlet of the drum.
Connect the power supply for use
of the appliance (make sure the
switch is on the OFF position
before the power supply is
connected).
12

Put food ingredients into the feed
chute on the drum and then push
the food ingredients with help of
the plunger.
After the “SOFT or HARD” button
of the switch is pressed, the
appliance will begin to run for
10 minutes or a shorter time.
Wash vegetables and fruits, cut
them into blocks fitting the size
of the feed port and put them
on the tray.
13

14

15

16

Take down the plunger
Press the locking button on the
side of the drum and turn the
drum clockwise at the same
time to take out the drum.
The drum cannot be dismantled
if the button is not pressed.
After taking down the drum,
take down the juicing button
(or the noodle button and so on),
the tray, the juice strainer (or
the end cap) and the auger in
order. The dismountable parts
may be flushed with clean water.
17

ZM1507
18

Correct Disposal of this product
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources.
To return your used device, please use the
return and collection systems or contact the
retailer where the product was purchased.
They can take this product for environmental
safe recycling.
Manufacturer:
Zhongshan Jimi Electrical Appliance Co., Ltd.
Add.: 9 of No.35 dadaozhong jixi Industrial, Xiaolan Town, Zhongshan, Guangdong, China
19
EC REP
E-Gate Germany GmbH
Marzahner Str. 34 D-13053 Berlin Germany
The device meets the requirements of Regulation 2014/30/EU as
well as the applicable standards EN55014-1:2017,EN55014-2:2015,
EN IEC 61000-3-2:2019, EN61000-3-3:2013+A1:2019
WEEE-Reg.-Nr.DE 20193320
LUCID-Reg.-Nr.DE5698760378353

20