Analytic Systems PWS1510MS User manual

Installation &
Operation Manual
PWS1510MS
Power Supply
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com

2
Copyright (2005-2013) Analytic Systems Ware (1993) Ltd.

3
IMPORTANT & SAFETY INSTRUCTIONS
1) SAVE THESE INSTRUCTIONS — is manual contains important safety and operating
instructions for power supply.
2) Do not expose power supply to rain or snow.
3) Use of an attachment not recommended or sold by the power supply manufacturer may result
in a risk of re, electric shock, or injury to persons.
4) Do not disassemble power supply; take it to a qualied serviceman when service or repair is
required. Incorrect reassembly may result in a risk of electric shock or re.
5) To reduce risk of electric shock, unplug power supply from outlet before attempting any main-
tenance or cleaning. Turning o controls will not reduce this risk.
6) Never place marine power supply directly above battery; gases from battery will corrode and
damage power supply.
7) Never allow battery acid to drip on power supply when reading gravity or lling battery.
8) O/P CONNECTION PRECAUTIONS
Connect and disconnect DC output connections only aer setting the power supply
switch to the o position.
GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS — e plug must be plugged
into an outlet that is properly installed and grounded in accordance with al local codes and ordinances.
DANGER — Never alter AC cord or plug provided — if it will not t outlet, have proper cord installed by a
qualied electrician. Improper connection can result in a risk of an electric shock.
Analytic Systems does not recommend the use of the PWS1510 Series Power Supplies in life support ap-
plications where failure or malfunction of this product can be reasonably expected to cause failure of the life
support device or to signicantly aect its safety or eectiveness. Analytic Systems does not recommend the
use of any of its products in direct patient care.
Examples of devices considered to be life support devices are neonatal oxygen analyzers, nerve stimulators
(whether used for anesthesia, pain relief, or other purposes), autotransfusion devices, blood pumps, debril-
lators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis systems,
neonatal ventilator incubators, ventilators for both adults and infants, anesthesia ventilators, and infusion
pumps as well as any other devices designated as “critical” by the U.S. FDA.

4
Specications
Introduction
All new Current Mode switching design oers increased power and reliability in a compact package. Extra
input and output ltering reduce EMI to extremely low levels. Reliability features include an input fuse,
thermal shutdown, current limiting and output short circuit shutdown with automatic recovery. e model
PWS1510 Power Supply supplies either 26, or 28 VDC from a 110 or 220 VAC power source.
Designed and manufactured by: ANALYTIC SYSTEMS WARE (1993) LTD.
8128 River Way, Delta, B.C., V4G 1K5, Canada
phone [phone] fax [phone] toll free 800-668-3884 US/Canada
email: [e-mail] web site: www.analyticsystems.com Revised May 2006
* Specications subjects to change without notice.
Input
Nominal (ip) Auto Select 110/220
Actual 90-130Vac / 180-260Vac
Input Amps (max) 15A max.
Input Fuse (slow blow) 25 A Breaker
Input Frequency 45 - 400 Hz
Output
Nominal (op) 26.0Vdc / 28Vdc
Actual 26.0 ± 0.05Vdc / 28.0 ± 0.05Vdc
Output Crowbar 32.0 / 34.0 ± 1.0 Vdc
Output Amps (cont) 25 A
Output Amps (max) 46 A (1/min)
General
Noise on Input < 50 milli-Volts
Noise on Output < 50 milli-Volts
Transient Response < 1 V for 50% surge
Eciency > 80 % @ maximum output
Temp. Range -25 to +40 deg. C @ maximum output
Isolation Input-Output, Input-Case & Output-Case 1500VDC
Isolation Output-Case 500VDC
Length 16.0 in / 40.64 cm
Width 8.34 in / 21.18 cm
Height 3.91 in / 9.93 cm (without carrying handle)
Clearance 1 Inch (2.5 cm) all around
Material Marine Grade Aluminum
Finish Clear chromate
Fastenings 18-8 Stainless
Weight 14.4 lb / 6.5 kg

5
All connections should be made inside an appropriate junction box. e maximum current draw from the
110 VAC supply is 16.2 amps, so a 20 amp circuit breaker should be used in the circuit panel and for a 220
VAC supply, 8.1 amps is the maximum current draw, so a 10 amp circuit breaker should be used in the circuit
panel to feed power to the power supply.
◆MOUNTING
Mount the unit in a DRY location. Allow at least 4 inches of clearance around the extrusion for adequate
cooling.
◆POWER CONNECTION
e unit is supplied with a 5 foot power cable. is should normally be adequate to connect to a source of
power. If you must extend the power cable be sure to use a 3 conductor grounded type extension cable. For
hard wiring to a source of power, cut o the plug, and strip the wires as necessary. e wire colours are
Installation
Operation
Turn the switch on the side of the unit on to energize the outputs. e green indicator light will glow to
indicate the proper operation of the unit.
Troubleshooting
f the load exceeds the continuous rating for too long a period, the temperature sensor inside the unit will
turn o the output. Aer the unit cools suciently, it will automatically come back on. If this happens
frequently, remount the unit for increased airow so it cools better.
110 VAC 220 VAC
Brown - AC Hot Brown - AC Hot / Phase 1
Blue - AC Neutral Blue - AC Neutral / Phase 2
Green - Ground Green/Yellow - Ground

6
Limited Warranty
1. e equipment manufactured by Analytic Systems Ware (1993) Ltd. (the “Warrantor”) is war-
ranted to be free from defects in workmanship and materials under normal use and service.
2. is warranty is in eect for:
a. 3 Years from date of purchase by the end user for standard products oered in our
catalog.
b. 2 Years from date of manufacture for non-standard or OEM products
c. 1 Year from date of manufacture for encapsulated products.
3. Analytic Systems will determine eligibility for warranty from the date of purchase shown on the
warranty card when returned within 30 days, or
a. e date of shipment by Analytic Systems, or
b. e date of manufacture coded in the serial number, or
c. From a copy of the original purchase receipt showing the date of purchase by the user.
4. In case any part of the equipment proves to be defective, the Purchaser should do the following:
a. Prepare a written statement of the nature of the defect to the best of the Purchasers
knowledge, and include the date of purchase, the place of purchase, and the Purchas-
ers name, address and telephone number.
b. Call Analytic Systems at 800-668-3884 or 604-946-9981 and request a return material
authorization number (RMA).
c. Return the defective part or unit along with the statement at the Purchasers expense to
the Warrantor; Analytic Systems Ware (1993) Ltd., 8128 River Way, Delta, B.C., V4G
1K5.
5. If upon the Warrantor’s examination the defect proves to be the result of defective material or
workmanship, the equipment will be repaired or replaced at the Warrantor’s option without
charge, and returned to the Purchaser at the Warrantor’s expense by the most economical means.
Requests for a dierent method of return or special handling will incur additional charges and are
the responsibility of the Purchaser.
6. Analytic Systems reserves the right to void the warranty if:
a. Labels, identication marks or serial numbers are removed or altered in any way.
b. Our invoice is unpaid.
c. e defect is the result of misuse, neglect, improper installation, environmental condi-
tions, non-authorized repair, alteration or accident.
7. No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable
to remedy the defect aer having a reasonable number of opportunities to do so.
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)

8. Only the Warrantor shall perform warranty service. Any attempt to remedy the defect by anyone
else shall render this warranty void.
9. ere shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse
or misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or
water immersion except for equipment specically stated to be waterproof.
10. No other express warranty is hereby given and there are no warranties that extend beyond those
described herein. is warranty is expressly in lieu of any other expressed or implied warranties,
including any implied warranty of merchantability, tness for the ordinary purposes for which
such goods are used, or tness for a particular purpose, or any other obligations on the part of the
Warrantor or its employees and representatives.
11. ere shall be no responsibility or liability whatsoever on the part of the Warrantor or its em-
ployees and representatives for injury to any person or persons, or damage to property, or loss
of income or prot, or any other consequential or resulting damage which may be claimed to
have been incurred through the use or sale of the equipment, including any possible failure of
malfunction of the equipment, or part thereof.
12. e Warrantor assumes no liability for incidental or consequential damages of any kind.
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com