Ancheer AM001907 User manual

E-bike User’s Manual
CAUTION READ THIS MANUAL BEFORE USING YOUR EQUIPMENT

CONTANTS
Safety instruction------------------------------------------------------------------Page 1
Instruction-------------------------------------------------------------------------Page 1
Meter operation-------------------------------------------------------------------Page 2
Battery:Further information and maintenance-----------------------------------Page 3
Charging---------------------------------------------------------------------------Page 3
Installation Instruction----------------------------------------------------------Page 4-6

1. Safety Instruction ___________________
1. Thank you for purchasing the ANCHEER E-BIKE. The E-BIKE features the most
recent innovation in technology.
2. For Safety reasons, it is most important that you read this user’s manual before
you operate the bike. Improper handling can reduce its riding performance and
most importantly, cause danger to your safe and healthy.
3. For handling and maintenance of the bicycle, please refer to the E-BIKE user’s
manual which is an integral part of this e-bike user’s manual!
4. Do not at any time dismantle or disassemble any of the above e-bike
components!
5. Please check all parts are tighten and locked before riding.
6. Please make sure that the battery charger and charging plug are always kept dray
and never get wet.
7. The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or
any other liquid.
2. Instruction
-1-

3. Meter operation
3.1 Meter instruction
3.2 Meter operation
3.3 Operation Cautions
Be careful of the safety use. Don’t attempt to release the connector when
charging the battery.
●Avoid the risk of collision.
●D o n ’t modify system parameters to avoid parameters disorder.
●M ake the display repaired when error code appears.
Operating instructions
To switch on/off
the E-Bike
system, hold the
button for
2s. The default
value is “low”
pedal assist
level.
Press “+” to
crease into
pedal assist
level “Mid”.
Press “+”
again to move
into pedal
assist level
“High”. “High”
is the
maximum
power of PAS.
Full Electric
Function
(Pure electric
mode):
Press”-“, until
all the three
“low””Mid””Hi
gh” indicators
are off.
-2-

4. Battery: further information and maintenance
1. How far full charge battery can go? That depends on the loading weight,
road condition and battery capacity. But in the same condition, average
speeds can continuous longer travel range.
2. When storing the battery for a longer time period, (e.g. during winter time)
it is important to place the fully charged battery on a flat surface in a dry
place.
3.Attention: The battery should be re-charged once every 2-3 month when it
is not used.
4.Warning:
4.1.Keep the battery out of reach for children.
4.2.Never try to open the battery.
4.3.If the battery is damaged because it has been dropped somewhere or
because of a biking accident, there might be a risk of electrolytes leakage.
Beware of chemical burns! And immediately stop using a damaged battery.
4.4Do not touch the battery without a cloth or gloves and make sure no acid
touches your eyes.
5. Charging
1. To charge the battery with the bike, simply place the bike within reach of
the power supply and plug it in. Note: The plug hole is located in the left of
the battery.
2. The battery can either be charged while on the bike or the battery can be
removed and charged at a place of your convenience.
3. The RED light indicates it is in charging and GREEN light indicates the
battery is fully charged. (Please put off plug from wall) Usually the charging
time is 4-6 hours depends on the battery capacity remain.
4. Warning: Charging time over 10 hours is prohibited please kept it away
from high temperature environment and stores it in a cool place.
-3-

6. Installation Instruction
1.Installation video please refer to:
https://drive.google.com/file/d/0B8ArYrneLylHeHhVZzUzU1pUUXM/view
( Could ask our customer service for the video).
2. When open the bike's carton box, take out E-bike and use tools to cut off
the package strings.
3. Install the handlebar:
3.1 use inner hexagon tool to loosen the stem cover and don't tighten all bolts
immediately before adjusting the handlebar in a property angel and position,
3.2 then tighten with tool.
3.1 3.2
4. Install front wheel:
4.1: take out the protection axle the front fork and front hub, and then take
out front wheel.
4.2 take out the front disc from tool box, install the disc on the hut of front
wheel. Attention:there is indicate sticker show which surface out side!
4.3 make sure front wheel is in line with the rear wheel and proceed to install.
(pull the wheel upwards and insert it in the fork drop outs then, insert the
safety washers on each side and tighten bolts on each side)
4.4.Used tool to tighten (left and right)
4.1 4.2 4.3
-4-

4.3 4.3 4.4
5.Install the front light
5.1 Take the screw from the fork;
5.2 Open the lamp
5.3 Install the lamp and used the tool to tighten it.
6 .Install pedals: Check 2 pedals, the one imprinted "L" should install in left
side and "R" in right side. Please use wrench to tighten them.
-5-

7. Install the Seat post.
7.1. Open the seat post and saddle, then install the rear reflector;
7.2 Put the seat post into the frame.
7.3 Adjust seat post to the height that suits your riding position best and
tighten quick release. ( Please make sure that the quick release is tightened
firmly.）
7.1 7.2 7.3 7.3
8. Adjust angle of brake lever, meter,gear shifter,throttle and louder
controller on handle bar, then tighten them with tools.
9. Install battery
9.1 Open the box of battery
9.2 tube the battery to correct angle and insert the battery into the holder
gently, press it down and lock automatically.
9.3 power on the battery with power bottom. “0” means off,”I”means on.
9.2 9.3
More ANCHEER electric bike’s installation and repair instructions please
search ANCHEER SPORT on Youtube. Our Youtube channel:
https://www.youtube.com/channel/UCtl3IkK0U0GqIL7c8AJf4pA
Any question about the item,please contact us:[e-mail]
-6-

Detail Packing List
Model
Descripation
Quantity
AM001907
Bike
1
Tool (open-end spanner13-15, open-end
spanner14-17,screwdriver,inner hexagon
spanner M6,M5,M4)
1
Manual
1
Key
2
Charger
1
Battery
1
Pedal
1
Reflactor
1
(
底面空白）