Angel Electronics SleepHalo User manual
Before using your SleepHalo™ we
recommend reading this guide to
prevent any damage that could occur
due to misuse.
We also recommend registering your
product on our website to activate your
2 year warranty.
Visit: www.sleephalo.com/register
Package Contents
Compatibility for Wireless Charging
SleepHalo™ has been designed to be compatible with Qi enabled phones. A list
can be found on our website.
If your phone is not wireless compatible it can still be used with your existing
wired charger by placing the plugged-in phone onto SleepHalo™. You will then
benet from the radiation protection offered by SleepHalo™.
SleepHalo™ Charger Base
Radiation Shield
LED Indicator
Power Adapter (UK)
1M Cable
SleepHalo™ User Manual V1.1 E&OE Page 1 of 6
Connecting your SleepHalo™
Decide which side of the bed you wish to place your SleepHalo™, noting that the
raised protection shield should be between you and the phone. On the underside
of the product you can route the power cable in 2 directions. Choose which route
is best, plug in the connector to the power port and clip the cable through the
rebated area.
Connect SleepHalo™ USB connector
into the power adapter.
Plug SleepHalo™ power adapter into
a wall socket.
Power Port
Cable clipped into
rebate in base.
Non-slip feet avoid
SleepHalo™ slipping
or scratching the
surface it is placed on.
SleepHalo™ User Manual V1.1 E&OE Page 2 of 6
Using your SleepHalo™
To charge wirelessly, the phone must be placed onto SleepHalo™ with the screen
facing up. The indicator LED on the side will change from red to blue once phone
is correctly placed. Place the phone on the centre of SleepHalo™.
If the red LED ashes, this indicates the phone is not aligned correctly. Fully
remove and then replace. Correct charging can also be conrmed by checking the
screen of your phone for the charge icon.
LED Colour SleepHalo™ Status
Red Standby
Blue Charging
Green Fully Charged (dependent on phone)
Flashing Phone not aligned correctly
Or foreign object detected
LED Indicator
Outline of phone
Use logo for
alignment
SleepHalo™ User Manual V1.1 E&OE Page 3 of 6
SleepHalo™ has rubber feet attached to the bottom to prevent it slipping. If you
have a phone with a magnetic back, then sticky feet can be purchased from our
website to hold SleepHalo™ down.
How to position SleepHalo™ on bedside table
For further set-up information and Troubleshooting please visit our support page
at www.sleephalo.com or email us at support@angelelectronics.com
Sticky Feet can be
applied here
Radiation Shield
When positioning SleepHalo™, position it so that when you are laying down you
cannot see the screen of your phone.
SleepHalo™ User Manual V1.1 E&OE Page 4 of 6
Safety Information
Specication
• Using a different power adapter other than the one supplied with SleepHalo™
is at your own risk.
• Do not disassemble SleepHalo™, it is a sealed device.
• Whilst the phone is charging do not cover.
• Do not place anything other than your phone onto SleepHalo™.
• Do not use outdoors or in damp conditions.
• Unplug if SleepHalo™ is not used for extended periods of time.
• If you can see damage to SleepHalo™ do not use.
• To clean SleepHalo™ unplug and use a soft damp cloth.
• Depending on your phone, you might hear faint noises while you
phone charges.
• Do not place anything between your phone and SleepHalo™. Remove
anything (credit cards) that are stored in the back of your phone case.
Power Adapter
SleepHalo™
• AC Adapter : 100-240V, 50/60 Hz 0.3A
• Output : 5V 1A
• Input: 5V 1A
• Output: 5W
SleepHalo™ is a trade mark is a trade mark of Angel Electronics Ltd ©
SleepHalo™ User Manual V1.1 E&OE
•Wireless Range : 5mm
Page 5 of 6
SleepHalo™ is a trade mark is a trade mark of Angel Electronics Ltd ©
SleepHalo™ User Manual V1.1 E&OE
Declaration of Conformity (FCC)
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Page 6 of 6
Table of contents
