Ankom 10 Station User manual
Automationsavestimeandmoney!
ANKOMTechnologyisaninternationalcompanywithproductsthat
include…
A2000FiberAnalyzer
Crude Fiber (AOCS Ba 6a-05), ADF, NDF
Automatically adds solutions and rinses
Batch process - up to 24 samples at one time
XT15FatExtractor
Official Method AOCS Am 5-04
Fully automatic
Solvent recovery at 97% or greater
Batch process - up to 15 samples at one time
RFGasProductionSystem
Measures Kinetics of Microbial Metabolism
Examination of Biodegradability
Biological Oxygen Demand (BOD)
High Sensitivity Pressure Measurement
Chemicals
A wide variety of chemicals used for many
different lab operations
Pre-mixed solutions available
Pleasevisitourwebsiteatwww.ankom.comformoreinformation.
2052O’NeilRd.
Macedon,NY14502
Tel:(315)986–8090
Fax:(315)986–8091
www.ankom.com
10Station
BatteryCharger
U
U
Us
s
se
e
er
r
r
G
G
Gu
u
ui
i
id
d
de
e
e
RevA10/30/09
Introduction
BatteryChargerFrontView
ANKOM Technology develops, manufactures and markets analytical instrumentation
and support products that serve multiple international industries. Committed to Total
Customer Satisfaction, ANKOM develops every product based on a thorough
assessment of customer needs.
Congratulations on your purchase of theANKOM 10 Station Battery Charger.We are
confident that this product will effectively serve your needs.
Warranty
UsingyourBatteryCharger
ANKOM Technology warrants the ANKOM 10 Station Battery Charger against any
defects due to faulty workmanship or material for six months after the original date of
purchase. This warranty does not include damage to the instrument resulting from
neglect or misuse. If the instrument is damaged as a result of defects in the
workmanship or materials during the warranty period, ANKOM will repair or replace
the instrument free of charge.
Before using your ANKOM 10 Station Battery Charger, please read the information
below.
Use this charger only with ANKOM RF16 battery packs (green labels).
Connect the power supply to the back of the battery charger, and then plug it
into a standard electrical outlet (110V or 220V dependent on model ordered).
Use only the power supply and cable supplied with the unit.
Push the toggle switch on the front panel of the battery charger up to turn it on.
The two RED lights next to the switch should come on.
Connect the RF 16 battery packs to the charger. Note that the connector has a
locking tab which must be pressed to disconnect the battery. Do not force the
connector.
Battery Packs do NOT have to be fully discharged before being
connected to the charger.
Each station on the charger has a RED light and a GREEN light. When a
battery is connected, the RED light should come on within 5 minutes. This
indicates the battery is charging. If the RED light does not come on within 5
minutes, the battery pack may be faulty, or there may be a problem with that
station.
Individual charging stations can be used at any time. You do NOT
have to use every charging station at once to use the charger.
When the RED and GREEN lights for a specific station are fully lit, the battery
pack connected to that station is fully charged. Remember to wait until both
lights are fully lit. A fully discharged battery should charge within 3 hrs.
Disconnect battery packs when charging is complete. Battery packs can be
connected and disconnected from the charger with the charger power ON.
Your Battery Packs will NOT be damaged if you leave them
connected to your charger after they are fully charged.
Keep the power OFF when the charger is not being used.
ContactInformation
ANKOM Technology is committed to your total satisfaction and is therefore always
available to help you get the most from your ANKOM products. We are also very
interested in any comments or suggestions you may have to help us improve.
For any questions or suggestions regarding your instrument, please contact us at:
Telephone: (315) 986-8090
Fax: (315) 986-8091
www.ankom.com
